Massachusetts General Laws define three classes of motorized two-wheeled vehicles: Motorcycle, Motorized bicycle, and Motorized scooter. Although the definition of motorized scooter includes two-wheeled vehicles propelled by electric motors with or without human power, motorized scooter specifically excludes anything which falls under the definitions of motorized bicycle and motorcycle. Motorized bicycle is a pedal bicycle which has a helper motor, or a non-pedal bicycle which has a motor, with a cylinder capacity not exceeding fifty cubic centimeters, an automatic transmission, and which is capable of a maximum speed of no more than thirty miles per hour. Motorcycle includes any bicycle with a motor or driving wheel attached, with the exception of vehicles that fall under the specific definition of motorized bicycle. Thus, a pedal bicycle with an electric motor or a non-pedal bicycle with an electric motor, automatic transmission, and maximum speed of 30 miles an hour would fall under the definition of motorized bicycle. An electric bicycle that did not meet those restrictions would be either a motorized scooter or motorcycle, depending on specific characteristics.
We spent 46 hours on research, videography, and editing, to review the top choices for this wiki. Despite their growing popularity among commuters and recreational cyclists, most e-bikes aren't designed to fit easily into the trunk of a car or on crowded public transit systems. So for more portable pedaling power on the way to and from work, or wherever you roam, just pick up one of these handy folding electric models. They are as useful as their non-folding brethren, only more convenient. When users buy our independently chosen editorial picks, we may earn commissions to support our work. Skip to the best folding electric bike on Amazon.
Being member of European Economic Area (EEA), Norway implemented the European Union directive 2002/24/EC. This directive defined legal ebikes for all EU and EEA countries to "Cycles with pedal assistance which are equipped with an auxiliary electric motor having a maximum continuous rated power of 0.25 kW, of which the output is progressively reduced and finally cut off as the vehicle reaches a speed of 25 km/h or if the cyclist stops pedaling.” The definition became part of Norwegian vehicle legislation in 2003. A more detailed specification will become effective when the new European ebike product safety standard EN 15194 is published in 2009.
Bicycles helped create, or enhance, new kinds of businesses, such as bicycle messengers, traveling seamstresses, riding academies, and racing rinks. Their board tracks were later adapted to early motorcycle and automobile racing. There were a variety of new inventions, such as spoke tighteners, and specialized lights, socks and shoes, and even cameras, such as the Eastman Company's Poco. Probably the best known and most widely used of these inventions, adopted well beyond cycling, is Charles Bennett's Bike Web, which came to be called the jock strap.
We've also released our first native 72V battery pack in a conventional downtube battery casing, assembled using the high power Samsung 27100 40T cells so that even with the small 8Ah capacity it is able to deliver 40-50A continuous currents. This is an ideal battery for fast and sporty offroad ebike builds, allowing powerful performance without the weight or complexity of most 72V setups (either two 36V packs in series or a large triangle frame battery).
Different gears and ranges of gears are appropriate for different people and styles of cycling. Multi-speed bicycles allow gear selection to suit the circumstances: a cyclist could use a high gear when cycling downhill, a medium gear when cycling on a flat road, and a low gear when cycling uphill. In a lower gear every turn of the pedals leads to fewer rotations of the rear wheel. This allows the energy required to move the same distance to be distributed over more pedal turns, reducing fatigue when riding uphill, with a heavy load, or against strong winds. A higher gear allows a cyclist to make fewer pedal turns to maintain a given speed, but with more effort per turn of the pedals.
If you're taking your bike inside, consider one that folds up. The Cyclotricity Wallet has a motor in the front wheel, which takes you up to speed either by assisting your pedalling, or you can sit back and use the throttle by itself. Its folding design makes it slightly easier to get in and out of a building, but its hefty weight means you still won't find it easy to carry onto public transport.
The other shout-out goes to Paul Bogaert who decided to close the Bike Doctor after 27 years and instead cycle tour the world with his wife. Paul had an early role in Vancouver bicycle advocacy and at bringing cycle riding to a less elitist/athletic and more everyday commuter crowd through their shop. They were among the early shops to embrace family friendly cargo bikes and appreciated the role that electric would play in making cycling more broadly appealing.
The environmental effects involved in recharging the batteries can of course be reduced. The small size of the battery pack on an e-bike, relative to the larger pack used in an electric car, makes them very good candidates for charging via solar power or other renewable energy resources. Sanyo capitalized on this benefit when it set up "solar parking lots", in which e-bike riders can charge their vehicles while parked under photovoltaic panels.
I am very pleased with the quality and performance of this electric bike. I find that the twist grip throtle works better for me than the peddle assist low, medium and high settings. It is not necessary to change out of high gear to climb most hills while peddling with the throttle also providing power. The shocks work well on dirt paths and the seat is comfortable. This bike goes maximum speed up to 19 mph on flat ground. I have
The recommendation depends a lot on what you plan to use the bike for and how you plan to ride. That said, I would recommend at least a 750 (if not 1,000) watt motor, and, if you want reasonable range, 48 or 52v cells with a minimum rating of 19ah. For shorter rides, you can use a smaller battery. Multiply battery voltage by amp hour rating to get battery watt hours. Divide the watt hours by the motors power rating to get a general idea of how many hours of heavy use you might get. I’d also recommend a mid drive as opposed to a hub drive, or to find a hub drive wheel rated to take your and the bicycle's combined weight.
Are you looking for an easier way to get to your blind or tree stand? Or perhaps check all your trail cams in a fraction of the time it takes today? Is that sweet spot you know getting harder to reach? When you have to carry 50lbs of gear on your back for 5 or even 10 miles and if you’re lucky you have something to haul back out, using an electric bike built specifically for offroad and woodlands that is also capable of carrying your gear, wouldn’t that make the experience a whole lot more enjoyable? Electric hunting bikes...
A lot has happened since we founded the very first eMTB specific magazine in 2013. In the beginning, manufacturers simply mounted electric motors on regular mountain bikes, more or more often than not, rather less successfully. Last year a lot of brands focused on the topic of battery integration. There are some exciting new trends and developments headed our way next season, which we take a closer look at below.
The Riese & Müller Load Touring HS is billed as “the ultimate minivan of e-bikes,” and it holds up to that claim. With a low center of gravity (aided by the 20-inch front and 26-inch rear wheels), the Load is easy to handle. Tektro hydraulic disc brakes add control, and front and rear suspension provide comfort. The Bosch motor offers an assist up to 275 percent of your effort until you hit 28 mph, when it cuts out. Two 500Wh batteries give you 12 hours or more of range at full power. It’s capable of toting up to 220 pounds of pets, people, and less-animate cargo. R&M also sells a double child seat for kids up to age 6 and a child-seat fastener for your youngest passengers.
In conformance with legislation adopted by the U.S. Congress defining this category of electric-power bicycle (15 U.S.C. 2085(b)), CPSC rules stipulate that low speed electric bicycles (to include two- and three-wheel vehicles) are exempt from classification as motor vehicles providing they have fully operable pedals, an electric motor of less than 750W (1 hp), and a top motor-powered speed of less than 20 miles per hour (32 km/h) when operated by a rider weighing 170 pounds. An electric bike remaining within these specifications is subject to the CPSC consumer product regulations for a bicycle. Commercially manufactured e-bikes exceeding these power and speed limits are regulated by the federal DOT and NHTSA as motor vehicles, and must meet additional safety requirements. The legislation enacting this amendment to the CPSC is also known as HR 727. The text of HR 727 includes the statement: "This section shall supersede any State law or requirement with respect to low-speed electric bicycles to the extent that such State law or requirement is more stringent than the Federal law or requirements." (Note that this refers to consumer product regulations enacted under the Consumer Product Safety Act. Preemption of more stringent state consumer product regulations does not limit State authority to regulate the use of electric bicycles, or bicycles in general, under state vehicle codes.)
Übrige "Motorfahrräder": “E-Bikes mit einer Leistung zwischen 500 und 1000 Watt oder einer bauartbedingten Höchstgeschwindigkeit von 20 bis 30 km/h oder einer Tretunterstützung, die auch bei einem Tempo von 25 – 45 km/h wirkt, gelten als Motorfahrräder und benötigen ein entsprechendes Kontrollschild.”. You can use any bicyle path and also hiking roads forbidden to motorbikes if you drive slowly.
Oregon Law (ORS 801.258]) defines an electric assisted bicycle as an electric motor-driven vehicle equipped with operable pedals, a seat or saddle for the rider, no more than three wheels in contact during travel. In addition, the vehicle must be equipped with an electric motor that is capable of applying a power output of no greater than 1,000 watts, and that is incapable of propelling the vehicle at a speed greater than 20 miles per hour on level ground.
The Registrar will permit an electric motor driven cycle to be registered if it meets Canada Motor Vehicle Safety Standards (CMVSS) as a Limited Speed Motorcycle, or Scooter as is done with gas powered motor driven cycles. If the vehicle was manufactured after 1988 it will bear a compliance label stating that it meets these standards. The operator will be subject to all the requirements placed on operators of motor driven cycles.
Range is a key consideration with e-bikes, and is affected by factors such as motor efficiency, battery capacity, efficiency of the driving electronics, aerodynamics, hills and weight of the bike and rider. Some manufacturers, such as the Canadian BionX or American Vintage Electric Bikes, have the option of using regenerative braking, the motor acts as a generator to slow the bike down prior to the brake pads engaging. This is useful for extending the range and the life of brake pads and wheel rims. There are also experiments using fuel cells. e.g. the PHB. Some experiments have also been undertaken with super capacitors to supplement or replace batteries for cars and some SUVS. E-bikes developed in Switzerland in the late 1980s for the Tour de Sol solar vehicle race came with solar charging stations but these were later fixed on roofs and connected so as to feed into the electric mains. The bicycles were then charged from the mains, as is common today. While ebike batteries were produced mainly by bigger companies in past, many small to medium companies have started using innovative new methods for creating more durable batteries. State of the art, custom built automated precision CNC spot welding machines created 18650 battery packs are commonly used among Do-it-yourself ebike makers.
In the United States electric bikes have seen slow but steady growth since the late 90’s and as a result, in 2001 congress was lobbied and passed the first and only bill to define ebikes in federal law. This law, 107-319, exempts electrified bicycles with operating pedals using motors under 750 watts limited to 20 mph from the legal definition of a motor vehicle.2.
Our hope is that this plug will become to motors in the 500-1500 watt power range what the 9pin Z910 became for the low power geared motors, with all motor manufacturers agreeing to the same pinout standard for easy swapping and interchangeability . We have an L10 version of the Phaserunner motor controller available now and will soon be expanding this to a Grinfineon offering as well.
E-bikes are classed according to the power that their electric motor can deliver and the control system, i.e., when and how the power from the motor is applied. Also the classification of e-bikes is complicated as much of the definition is due to legal reasons of what constitutes a bicycle and what constitutes a moped or motorcycle. As such, the classification of these e-bikes varies greatly across countries and local jurisdictions.
GPS Firmware: This net update will be much appreciated by people who have a GPS Analogger device with their CA3. With a simple hardware modification to the Analogger circuit, the GPS data will be transmitted from your existing TRS cable back to the Cycle Analyst. You can then see the time of day, your elevation, position, and direction all on the CA3 screen. The firmware also features additional custom views on the main screen, allowing you to replace or toggle the battery voltage with any of these new parameters to get just the display you are after.
I would advocate you ride legal within the laws of your state. I would also look into some kind of liability rider or umbrella policy with your home owner’s policy, which covers your personal liability and theft. Get your bike registered; wear your helmet, eye protection, whatever is required by state law so that if an accident occurs and you are at fault, there is no legal recourse. Even if you own a 750W/20mph ebike that meets the definition of a bicycle, any at-fault cyclist may still be denied coverage by stingy insurance companies who want to support their clients. Your health insurance will usually cover your medical bills, but the costs of an expensive ebike may be lost.
The aluminum, step-through eJoy is the happy medium between traditional-looking townies that don’t transport much more than the rider and often cumbersome cargo models that are sometimes a challenge to store. With 26-inch wheels, full fenders, a Shimano Alivio nine-speed drivetrain and disc brakes, a wheelbase similar to the average townie, and a big, comfy seat, it has the appearance of a practical everyday cruiser. But its oversize rear rack, silent Bosch Active Line motor, heavy-duty head tube with front-tray mounts (the tray is an add-on), integrated Supernova E3 lights, and roll-over-anything balloon tires hurtle it into hmm-this-could-actually-replace-my-car status. It’s one of the quietest, most convenient, most stylish, and easiest-to-operate e-bikes available.
This year was busy at Haibike’s EUROBIKE stand. The reason: the new FLYON series, which we could only admire behind glass. The new bikes are the spearhead of Haibike’s eMTB development with an exciting and unprecedented level of integration and connectivity. They have a specially developed display, their own remote and, thanks to a 5,000 lumen headlight, are able to turn night into day. To make the rider visible at all times, taillights are neatly integrated into the frame. The bikes also come with the most powerful motor currently available on the market, from TQ Systems. We are sure that many will buy this bike not only for its performance but also as a status symbol.
The cargo bike is run by Escargo, and their delivery rider Elric Prynn cycles the delivery bike (he calls her Matilda) from the Quay up the cycle paths to the city centre, avoiding road traffic delays on the Exeter Bridges. The cargo bike is used to deliver hundreds of loaves of bread each day. Escargo was set up in September 2017 by ex-management consultant Jenny Ryding, and the delivery bike was specially made for Jenny by Iceni Cycles in Somerset.
Across Europe, where e-bikes were embraced by the public long before the rest of the world, e-bike growth has averaged in excess of 20 percent each year between 2014 and 2017, with a whopping 25.3 percent growth to a total of two million e-bike sales in 2017. Analysts predict that strong growth will continue, with worldwide e-bike sales expected to hit $23.83 billion by 2025. A lot of that growth will be right here in the US.
Ontario is one of the last provinces in Canada to move toward legalizing power-assisted bicycles (PABs) for use on roads, even though they have been federally defined and completely legal in Canada since early 2001. In November 2005 "Bill 169" received royal assent allowing the Ministry of Transportation of Ontario (MTO) to place any vehicle on road. On October 4 2006 the Minister of Transportation for Ontario Donna Cansfield announced the Pilot Project allowing PABs which meet the federal standards definition for operation on road. PAB riders must follow the rules and regulations of a regular bicycles, wear an approved bicycle helmet and be at least 16 years or older. There are still a number of legal considerations for operating any bicycle in Ontario. 
Biking is awesome, but biking uphill is not. Commuting by bike is environmentally friendly, fun and good for your health, but presenting your sweaty self to your office coworkers in not fun at all. Fortunately, there is a solution! Electric bicycles offer the same great benefits as traditional bicycles including cost savings, health improving, plus some additional advantages like efficiency in climbing hills, less stress on knees and joints, which is convenient for people of all ages and health.
Artwork: Hub motors aren't the only way to power electric bicycle wheels. If you've ever watched a mouse scampering around inside an exercise wheel, you might have wondered if you could drive a wheel electrically, in a similar way, with something that pushes against the inside of the rim. A company called GeoOrbital has been developing an ingenious mechanical equivalent that can be used to power conventional bikes—and here's a simplified illustration of how it works. It has a motorized drive roller (red) that presses against the inner rim, powered by a battery pack (orange) that sits snugly inside the wheel. Two guide rollers (blue) mounted on a tensioned framework (green) take the place of the conventional arrangement of spokes. According to GeoOrbital, you can fit one of its wheels to a normal bike in just 60 seconds.
But electric bicycles—e-bikes—are new territory for me. Broadly speaking, there are two basic options in e-bike land: power-on-demand and pedal-assist. With the former, the rider can control the speed with a throttle instead of just pedaling. Think moped but with an electric motor instead of internal combustion. Pedal-assist, by contrast, requires the rider to do some of the work. The electric motor won't engage unless the rider is pedaling.