E-bikes are classified in three different types: Class 1 and Class 3 bikes are powered proportionally to the “input” a rider gives via pedaling. “It feels natural, and you’re still riding a bike, so all your reflexes, skill and comfort you’ve developed over years of riding bikes apply immediately,” says Fritz Rice, sales manager of Gregg’s Cycles, near Greenlake.
Hub motors are sold as either geared or direct drive: Geared hubs are preferred for hill climbing ability and zero drag when coasting, while DD hubs are more durable and suitable for high speed. Extreme hill climbing and high torque applications (fatbikes, hauling cargo, popping wheelies) usually requires a mid drive, which is covered in the motor section below. Ebike battery packs from the listed suppliers are generally compatible with kits from any supplier, at worst you may need a different connector, which can be easily replaced. You probably want a battery pack that is 36, 48, or 52 volts, depending on whether you prefer lower price and longer range or a higher topspeed. DIY lipo battery packs can be built cheaply but doing so can be a fire hazard so actual packs are recommended. All hub motors above 24 V should be installed with torque arms for safety.
The two most common electric motor styles used in today’s e-bikes are hub motors and mid-drive motors. The Freedom uses a hub motor, which was located in the center of the rear wheel. Hub motors typically don’t offer the same natural maneuverability as the increasingly more common (and more expensive) mid-drive motors because their weight is concentrated in the rear of the bike. It can be jarring when the motor prevents you from going faster than the allotted speed, especially when cruising downhill, but 20 mph is the legal maximum for e-bikes in the US. (In the EU, it’s even lower: 25 km/h, or 15.5 mph.)
I'm wondering if renter's insurance will cover my eBike while I'm out cycling around town to work, shopping, or even on long distance eBike tours ….. And what exactly will the insurance cover … only the bicycle …. all of the extra features …. gadgets … gear ….. This beast will cost me around $9,500.00 (US) when finished. At times I will be carrying as much as $3,000.00+ worth of gear !!!
To operate the bike, you have to pedal for a second or so before the thumb throttle becomes active. This is often a cost and energy-saving measure designed into electric bicycles and scooters. Being able to start the motor from rest requires extra sensors and higher battery power. Starting the motor while it is in motion removes the need to install extra sensors in the motor (and thus removes one more possible failure or maintenance issue) and also eeks more range out of the battery by putting the energy intensive initial startup responsibility solely on the rider.
We spent 46 hours on research, videography, and editing, to review the top choices for this wiki. Despite their growing popularity among commuters and recreational cyclists, most e-bikes aren't designed to fit easily into the trunk of a car or on crowded public transit systems. So for more portable pedaling power on the way to and from work, or wherever you roam, just pick up one of these handy folding electric models. They are as useful as their non-folding brethren, only more convenient. When users buy our independently chosen editorial picks, we may earn commissions to support our work. Skip to the best folding electric bike on Amazon.

Another type of electric assist motor, often referred to as the mid-drive system, is increasing in popularity. With this system, the electric motor is not built into the wheel but is usually mounted near (often under) the bottom bracket shell. In more typical configurations, a cog or wheel on the motor drives a belt or chain that engages with a pulley or sprocket fixed to one of the arms of the bicycle's crankset. Thus the propulsion is provided at the pedals rather than at the wheel, being eventually applied to the wheel via the bicycle's standard drive train.
"Moped" means a device upon which a person may ride which has two or three wheels in contact with the ground, a motor having a maximum power output capability measured at the motor output shaft, in accordance with the Society of Automotive Engineers standards, of two horsepower (one thousand four hundred ninety -two watts) or less and, if it is a combustion engine, a maximum piston or rotor displacement of 3.05 cubic inches (fifty cubic centimeters) and which will propel the moped, unassisted, on a level surface at a maximum speed no greater than thirty miles per hour; and a direct or automatic power drive system which requires no clutch or gear shift operation by the moped driver after the drive system is engaged with the power unit.

From all the Chinese brands that have come and disappeared, Onway is still standing strong. That means that they have sold enough bikes, and they have been tried and tested enough for customers to know what to expect. So, what can you expect from this Onway bike? Well, for a very affordable price, you will get anything you realistically need in an e-bike – multi-purpose tires for various terrains, LCD display, LED headlights, taillights, a kickstand… Overall build quality and quality of the parts is above average, but there are some things that you will need to change, and seat should be the first on the list. Customer support is not that great, but if you decide to purchase this bike you will get a fun bike, for affordable price that you will be able to assemble and ride in no time.
In general, more expensive bikes are better. However, this is just a trend. E.g. the "Kassensturz" Consumer program from our state TV found in a 2012 study confined to an engineering school, that "Supermarket" bikes, e.g. the 1400 CHF (1200 Euro) "Leopard" bike from COOP did very well. Evaluation is "good" (almost the same as the three times more expensive 25km/h Stromer). They also pointed out a very bad model from a discounter. In other words, you can find good cheap models, but read the tests first.
In the United States electric bikes have seen slow but steady growth since the late 90’s and as a result, in 2001 congress was lobbied and passed the first and only bill to define ebikes in federal law. This law, 107-319, exempts electrified bicycles with operating pedals using motors under 750 watts limited to 20 mph from the legal definition of a motor vehicle.2.
In addition, Kalk weighs under 155 pounds — less than half of traditional motorbikes. Cake customized parts of the drivetrain and implemented an interior permanent magnet (IPM) motor. On a single charge, the bike travels up to 50 miles and as a bonus feature, maintenance is minimal due to the fact there are few moving parts thanks to its lack of a combustion engine.
From what we could tell from the launch photos, the bikes have 16x1 3/8-inch wheels, chain drive, an internally geared hub, and hydraulic disc brakes. They’re rounded out by full-coverage fenders, reflective-sidewall tires, ergonomic grips, a kickstand, and a bell. The company says the sleek, single-size aluminum frame fits riders between 5 feet and 6 feet tall.

Because the power is applied through the chain and sprocket, power is typically limited to around 250–500 watts to protect against fast wear on the drivetrain. An electric mid-drive combined with an internal gear hub at the back hub may require care due to the lack of a clutch mechanism to soften the shock to the gears at the moment of re-engagement. A continuously variable transmission or a fully automatic internal gear hub may reduce the shocks due to the viscosity of oils used for liquid coupling instead of the mechanical couplings of the conventional internal gear hubs.
Oregon Law (ORS 801.258]) defines an electric assisted bicycle as an electric motor-driven vehicle equipped with operable pedals, a seat or saddle for the rider, no more than three wheels in contact during travel. In addition, the vehicle must be equipped with an electric motor that is capable of applying a power output of no greater than 1,000 watts, and that is incapable of propelling the vehicle at a speed greater than 20 miles per hour on level ground.[124]
Toe-clips and toestraps and clipless pedals help keep the foot locked in the proper pedal position and enable cyclists to pull and push the pedals. Technical accessories include cyclocomputers for measuring speed, distance, heart rate, GPS data etc. Other accessories include lights, reflectors, mirrors, racks, trailers, bags, water bottles and cages, and bell.[52] Bicycle lights, reflectors, and helmets are required by law in some geographic regions depending on the legal code. It is more common to see bicycles with bottle generators, dynamos, lights, fenders, racks and bells in Europe. Bicyclists also have specialized form fitting and high visibility clothing.
In general, more expensive bikes are better. However, this is just a trend. E.g. the "Kassensturz" Consumer program from our state TV found in a 2012 study confined to an engineering school, that "Supermarket" bikes, e.g. the 1400 CHF (1200 Euro) "Leopard" bike from COOP did very well. Evaluation is "good" (almost the same as the three times more expensive 25km/h Stromer). They also pointed out a very bad model from a discounter. In other words, you can find good cheap models, but read the tests first.
The pedals on a motorised bicycle must be the primary source of power for the vehicle. If the motor is the primary source of power then the device cannot be classed as a motorised bicycle. For example, a device where the rider can twist a throttle and complete a journey using motor power only without using the pedals, would not be classed as a motorised bicycle.
The Consumer Product Safety Commission(CPSC) stipulates that commercially manufactured low-speed electric bicycles, or tricycles, must have fully operable pedals, an electric motor not exceeding 750W of power and a top motor-powered speed not in excess of 20 miles per hour (32 km/h).[22] An electric bike remaining within these specifications will be regarded simply as a bicycle for purposes of safety standards. This supersedes any state law that is more stringent, but only regarding safety equipment required on electric bicycles and the standard of manufacture they must meet.[23]. The legislation enacting this amendment to the CPSC is also known as HR 727[24].

This thing is also kitted out with a full SRAM groupset, RockShox Yari RC front shocks, Custom Fox Float suspension at the rear and enormously punchy SRAM disc brakes at the front and rear. Fundamentally, it's a mighty off-road machine with pro-spec kit that introduces a new style of trail riding, allowing adrenaline junkies to ride further, climb harder and descend faster than ever before.


State law defines a motorized pedalcycle as a motor-driven cycle equipped with operable pedals, a motor rated at no more than 1.5 brake horsepower, a cylinder capacity not exceeding 50 cubic centimeters, an automatic transmission, and a maximum design speed of no more than 25 miles per hour.[55] Subchapter J of Publication 45 spells out the vehicle requirements in full.
Experiments done in Uganda, Tanzania, and Sri Lanka on hundreds of households have shown that a bicycle can increase a poor family's income as much as 35%.[69][better source needed][70][71] Transport, if analyzed for the cost-benefit analysis for rural poverty alleviation, has given one of the best returns in this regard. For example, road investments in India were a staggering 3–10 times more effective than almost all other investments and subsidies in rural economy in the decade of the 1990s. What a road does at a macro level to increase transport, the bicycle supports at the micro level. The bicycle, in that sense, can be an important poverty-eradication tool in poor nations.

Power assisted bicycles are classified in two categories in Saskatchewan. An electric assist bicycle is a 2 or 3 wheeled bicycle (sic.: 3 wheeled bicycle) that uses pedals and a motor at the same time only. A power cycle uses either pedals and motor or motor only. Both must have engines with 500 watt power or less, and must not be able exceed 32 km/h (20 mph), i.e., electric motor cuts out at this speed or cycle is unable to go this fast on a level surface. The power cycle has to meet the Federal Motor Vehicle Safety Standards for a power-assisted bicycle. The power cycle requires at least a learner's driving licence (class 7), and all of the other classes 1-5 may operate these also. The electric assist bicycle does not require a licence. Helmets are required for both. Both are treated as bicycles regarding rules of the road. Gas powered or assisted bicycles are classified as motorcycles regardless of engine size or if using pedals plus motor. Stickers identifying the bicycle's compliance with the Federal classification may be required for power cycles by some cities or municipalities. [13]


While falling gas prices have temporarily halted years of gains in the number of bicycle commuters, more and more of us are using the bicycle to get around. It’s economical, provides good exercise, and is much cheaper than owning a car. But unless you’re in really good shape, you aren’t going to get very far. Enter the electric bike: a glorious new contraption allows us to get around without having to worry about arriving at our destinations a sweaty mess.

While falling gas prices have temporarily halted years of gains in the number of bicycle commuters, more and more of us are using the bicycle to get around. It’s economical, provides good exercise, and is much cheaper than owning a car. But unless you’re in really good shape, you aren’t going to get very far. Enter the electric bike: a glorious new contraption allows us to get around without having to worry about arriving at our destinations a sweaty mess.
The cargo bike is run by Escargo, and their delivery rider Elric Prynn cycles the delivery bike (he calls her Matilda) from the Quay up the cycle paths to the city centre, avoiding road traffic delays on the Exeter Bridges.  The cargo bike is used to deliver hundreds of loaves of bread each day.  Escargo was set up in September 2017 by ex-management consultant Jenny Ryding, and the delivery bike was specially made for Jenny by Iceni Cycles in Somerset.
China has experienced an explosive growth of sales of non-assisted e-bikes including scooter type, with annual sales jumping from 56,000 units in 1998 to over 21 million in 2008,[72] and reaching an estimated fleet of 120 million e-bikes in early 2010.[2][73] This boom was triggered by Chinese local governments' efforts to restrict motorcycles in city centers to avoid traffic disruption and accidents. By late 2009 motorcycles are banned or restricted in over ninety major Chinese cities.[72] Users began replacing traditional bicycles and motorcycles and e-bike became an alternative to commuting by car.[2] Nevertheless, road safety concerns continue as around 2,500 e-bike related deaths were registered in 2007.[73] By late 2009 ten cities had also banned or imposed restrictions on e-bikes on the same grounds as motorcycles. Among these cities were Guangzhou, Shenzhen, Changsha, Foshan, Changzhou, and Dongguang.[72][73]
In my research about ebikes and the law, I cannot begin to justify how often articles about the laws evolved into the various ways and techniques to sneak around public notice and be stealth with the your ebike. The goal is to ride fast and fun, stay away from public awareness, and ‘Fly under the Radar’. I have been there and I get the drift. Sales and production are up. Electric bike kits, DIY enthusiast, long distance commuters, and a general drive for value is raising the desire for more options for consumers, wanting speed for fun and function, while developing amnesia for the law. People want to ride their new ebikes, and have the same access to safe pathways as they did the week before on their 100% human bike. Rather than deal with the inevitable conflicts over access, behavior and perception within the general public, the typical user will try to blend in with the normal cycling community.

Gearless (Direct-Drive) Hub Motors – Some conversion kits (and bikes) use gearless, direct-drive motors. On this type of motor, the axle that passes through the center of the motor is actually the axle of the motor itself, with the copper windings fixed to the axle. The magnets are mounted to the outer shell of the hub motor. When electricity is applied to the stator a magnetic field is induced that causes the magnets to move. This in turn makes the whole shell of the motor turn and propels the e-bike forward. Even though corrosion will eventually have an impact, this type of motor should last for years since there’s no gearing and no contact between moving parts. They’re also capable of higher top speeds. But since there’s no gears, they have less torque and it requires more power to get the motor up to speed. Most direct-drive hub motors are 350w-500w and reach speeds of 18-25 mph. But more powerful motors can reach speeds of 35+ mph.
Nevada Electric Bicycle (NRS 482.0287) Bicycle 20 (motor only on the flat with 170LB rider, undefined if pedal assist is allowed to go faster) 750W (it is undefined as to whether this is input or output power, but in the USA, motors are rated on output power at the shaft) No none (use caution here because of "reckless endangerment" laws) no (not a "motor vehicle")
Biking is awesome, but biking uphill is not. Commuting by bike is environmentally friendly, fun and good for your health, but presenting your sweaty self to your office coworkers in not fun at all. Fortunately, there is a solution! Electric bicycles offer the same great benefits as traditional bicycles including cost savings, health improving, plus some additional advantages like efficiency in climbing hills, less stress on knees and joints, which is convenient for people of all ages and health.

As you evaluate the different folding electric bikes on the market, you’ll notice that there are a lot of inherent similarities from one brand to the next, even though the look of each brand’s attempt has some unique aspects to it. No matter how the bike looks, each of your options will have a motor that’s powered by a battery, a hinge that allows the bike to fold roughy in half, and a series of other features that you would regularly find on a normal bicycle, such as pedals, brakes, handlebars, etc.
Depending on local laws, many e-bikes (e.g., pedelecs) are legally classified as bicycles rather than mopeds or motorcycles. This exempts them from the more stringent laws regarding the certification and operation of more powerful two-wheelers which are often classed as electric motorcycles. E-bikes can also be defined separately and treated under distinct Electric bicycle laws.
In Australia the e-bike is defined by the Australian Vehicle Standards as a bicycle that has an auxiliary motor with a maximum power output not exceeding 200 W without consideration for speed limits or pedal sensors.[1] Each state is responsible for deciding how to treat such a vehicle and currently all states agree that such a vehicle does not require licensing or registration. Various groups are lobbying for an increase in this low limit to encourage more widespread use of e-bikes to assist in mobility, health benefits and to reduce congestion, pollution and road danger. Some states have their own rules such as no riding under electric power on bike paths and through built up areas so riders should view the state laws regarding their use. There is no licence and no registration required for e-bike usage.
In cities where bicycles are not integrated into the public transportation system, commuters often use bicycles as elements of a mixed-mode commute, where the bike is used to travel to and from train stations or other forms of rapid transit. Some students who commute several miles drive a car from home to a campus parking lot, then ride a bicycle to class. Folding bicycles are useful in these scenarios, as they are less cumbersome when carried aboard. Los Angeles removed a small amount of seating on some trains to make more room for bicycles and wheel chairs.[65]

The E-bike is everything it was advertised to be. It's big and fast and fun to ride especially when riding uphill with pedal assist you have the superhuman ability to get up those tuff climbs that would normally leave you winded and probably walking the bike. The setup was fairly simple however the frame had a couple of serious deep scratch marks in the otherwise impeccable paint job. And even though it's purely cosmetic it was still very disappointing to receive a brand new bike in this condition. It's not clear to me what if anything I can do about it but I still love the bike.
© 2019 Condé Nast. All rights reserved. Use of and/or registration on any portion of this site constitutes acceptance of our User Agreement (updated 5/25/18) and Privacy Policy and Cookie Statement (updated 5/25/18) and Ars Technica Addendum (effective 8/21/2018). Ars may earn compensation on sales from links on this site. Read our affiliate link policy.
×