We need to support and put our purchasing power behind ebikes sold in the U.S. that are trying to comply with the California rules which allow 500w and 750w nominal motors and establish 3 classes. If these bikes can create a big enough footprint in the market then future U.S. bike rules may universally adopt these standards. It is better than engaging in regulation showdowns without any standardized and unified proposal on the part of the Electric Bike Community.
To legally operate a motorized bicycle or electric-assisted bicycle the operator must be licensed, the motorized bicycle/electric-assisted bicycle must be registered in one of the following definitions and meet the required safety equipment. If the operator or the motorized bicycle/electric- assisted bicycle does not meet all requirements, they will not be legal for street/highway use (including the sidewalk).To qualify as a motorized bicycle under state law they need to have motor of a piston displacement capacity of 50 cubic centimeters or less, maximum of two brake horsepower, maximum speed of not more than Template:Convert on a flat surface, fully operable pedals for human propulsion are not required, but may be a part of the machine.
Riding position: You also may wish to check out an e-bike’s riding position before investing in it. For short trips, the riding position might not make much difference, but for long journeys, the upright "Dutch" style with pulled-back handlebars is very comfortable – particularly for tall riders. The same goes for mountain bike styles, though these bikes are not often designed to actually go off-road.
In Opinion No. 2007-00602 of the Attorney General, Jim Hood clarified that a "bicycle with a motor attached" does not satisfy the definition of "motor vehicle" under Section 63-3-103. He stated that it is up to the authority creating the bike lane to determine if a bicycle with a motor attached can be ridden in bike lanes. No specifications about the motor were made.
Photo: Zap Electric's power-assist kit turns a conventional bike into an electric one. There's a bolt-on DC electric motor (weighing just over 3kg or 7lb) just above the back wheel, behind the police officer's foot, pressing against the tire and driving it by simple friction. The motor's powered by a compact lead-acid battery (weighing about 5.5 kg or 12 lb) inside a protective nylon bag. This kit adds quite bit of weight to the bike, but gives extra range and speed when needed. Photo taken in Santa Rosa, California by Rick Tang courtesy of US DOE/NREL.
Maintenance of adequate tire inflation is the most frequent and troublesome concern for cyclists and many means and methods are employed to preserve pneumatic integrity. Thicker tires, thicker tubes, tire liners (of a number of rather impenetrable devices installed between the tire and tube), liquid sealing compounds squeezed into the tube, and automotive-style patch kits are all used to reliably contain the typical tire pressures of 40 to 60 pounds per square inch that are required for bicycle operation. Thin, light bicycle tires are particularly vulnerable to penetration and subsequent deflation caused by goat's heads and other burs, colloquially known as stickers. Inflation of bicycle tires to pressures higher than typical for automotive use requires special pumps. The complexity of bicycle tire maintenance and repair may cause many to not consider the bicycle for transport or leisure.
Available products (motors, senors, batteries, control systems. etc.) change fast since the e-bike market shows a strong growth. In principle, get a rear motor if you want a lot of raw power and acceleration (e.g. for a 500W motor). Middle motors are more energy efficient and less subject to problems (e.g. overheating). Middle motors usually are combined with integrated rear hub gears, and rear motors with derailleurs. Both have advantages and disadvantages. E.g. the former require less maintenance, are easy to use in go-and-stop traffic, but require taking off weight on pedals when shifting. Therefore the latter (derailleurs) are better for speedy overland and hills cycling.

Oregon Law (ORS 801.258) defines an electric assisted bicycle as an electric motor-driven vehicle equipped with operable pedals, a seat or saddle for the rider, no more than three wheels in contact during travel. In addition, the vehicle must be equipped with an electric motor that is capable of applying a power output of no greater than 1,000 watts, and that is incapable of propelling the vehicle at a speed no greater than 20 miles per hour on level ground.[54]

The bicycle is extraordinarily efficient in both biological and mechanical terms. The bicycle is the most efficient human-powered means of transportation in terms of energy a person must expend to travel a given distance.[38] From a mechanical viewpoint, up to 99% of the energy delivered by the rider into the pedals is transmitted to the wheels, although the use of gearing mechanisms may reduce this by 10–15%.[39][40] In terms of the ratio of cargo weight a bicycle can carry to total weight, it is also an efficient means of cargo transportation.
European Union directive 2002/24/EC exempts vehicles with the following definition from type approval: "Cycles with pedal assistance which are equipped with an auxiliary electric motor having a maximum continuous rated power of 0.25 kW, of which the output is progressively reduced and finally cut off as the vehicle reaches a speed of 25km/h (15.5mph) or if the cyclist stops pedaling." This is the de facto definition of an electrically assisted pedal cycle in the EU. As with all EU directives, individual member countries of the EU are left to implement the requirements in national legislation.
Bicycles were introduced in the late 19th century in Europe, and by the early 21st century, more than 1 billion were in existence at a given time.[1][2][3] These numbers far exceed the number of cars, both in total and ranked by the number of individual models produced.[4][5][6] They are the principal means of transportation in many regions. They also provide a popular form of recreation, and have been adapted for use as children's toys, general fitness, military and police applications, courier services, bicycle racing and bicycle stunts.
Some e-bikes operate in pedal-assist only, others have a throttle, and some have both. Generally, pedal-assist only bikes will provide multiple power settings to choose from to help customize your ride, while bikes with both throttle and pedal-assist will have limited pedal-assist options. With these bikes, the throttle provides full control (when needed) while pedal assist is just a secondary option, great on straightaways or open road.
Operators are subject to driving rules and equipment requirements (if applicable) when operated on the public streets or highways (which includes the main traveled portion of the road, shoulder and sidewalk). This means that an operator could be cited for speeding, failure to signal, unsafe change of course, driving on the sidewalk, DWI (this would apply to anywhere in the state and not just the streets/highways), and all other driving rules contained within state law that would apply. They may also not ride more than two abreast and may not impede the normal and reasonable movement of traffic. On a laned roadway, they must operate within a single lane.[citation needed]
Several bills have been sponsored to legalize electric bicycles for use on NYS roads, and several have overwhelmingly passed at the committee level, but none of these initiatives has been able to be heard and then passed in the New York State Senate, until 2015. The latest bill S3997, "An act to amend the vehicle and traffic law, in relation to the definition of electric assisted bicycle. Clarifying the vehicle and traffic law to define electric assisted bicycles; establish that electric assisted bicycles, as defined, are bicycles, not motor vehicles; and establish safety and operational criteria for their use." has passed in the Senate for the first time ever in 2015.[116] The related Assembly bill A233 was not brought to a vote in the assembly even though it had passed with little issue in prior years.[117]
As we already noted, roadways in many countries aren’t the ideal places for bicycles, as transportation engineers spent the last century or so designing them only to accommodate cars. The average bike rider moves at a pace that’s fast enough to surprise drivers, but slow enough to make it difficult for them to avoid dangerous situations. An electric bike’s increased speed helps to even the playing field, giving you the opportunity to quickly avoid an accident.

"Medical Exemptions" are also a standard right in the State of Texas for motorcycles & even bicyclists. Through Texas's motorcycle helmet law (bicycle helmet laws from city ordinances), it is only required for those 21 years old or younger to wear a helmet. However, a medical exemption,[133][134][135][136][137] written by a certified licensed medical physician or licensed chiropractor, which exempts one from wearing a helmet, can be used for bicyclists if helmets are required.


J. K. Starley's company became the Rover Cycle Company Ltd. in the late 1890s, and then simply the Rover Company when it started making cars. Morris Motors Limited (in Oxford) and Škoda also began in the bicycle business, as did the Wright brothers.[101] Alistair Craig, whose company eventually emerged to become the engine manufacturers Ailsa Craig, also started from manufacturing bicycles, in Glasgow in March 1885.
A 2008 market survey showed that the average distance traveled in the Netherlands by commuters on a standard bicycle is 6.3 kilometres (3.9 mi) while with an e-bike this distance increases to 9.8 kilometres (6.1 mi).[79] This survey also showed that e-bike ownership is particularly popular among people aged 65 and over, but limited among commuters. The e-bike is used in particular for recreational bicycle trips, shopping and errands.[79]
If you're taking your bike inside, consider one that folds up. The Cyclotricity Wallet has a motor in the front wheel, which takes you up to speed either by assisting your pedalling, or you can sit back and use the throttle by itself. Its folding design makes it slightly easier to get in and out of a building, but its hefty weight means you still won't find it easy to carry onto public transport.
The basic shape and configuration of a typical upright or "safety bicycle", has changed little since the first chain-driven model was developed around 1885.[7][8][9] However, many details have been improved, especially since the advent of modern materials and computer-aided design. These have allowed for a proliferation of specialized designs for many types of cycling.
You are not allowed to drive S-Pedelecs in France even if they are registered legally in your country (e.g. Germany or Switzerland). In other words, if you plan to take your 45h bike that is legal in your country on vacation in another where it is not, you may violate traffic law. Remove the license plate or don't do it. People who commute between countries, are known to hack removable plates with magnets ...
With a 150mm-travel RockShox Yari fork and 132mm of rear travel from the RockShox Monarch Plus R shock, the Remote CTRL is Kona’s first dual-suspension e-mountain bike. It’s powered by a 250-watt Bosch Performance Line XC mid-drive motor that uses the company’s progressive E-MTB mode that is adaptable to rider input, which means you don’t have to toggle through assistance modes while riding. It offers assistance up to 20 mph, and the 500Wh integrated battery is the largest Bosch currently offers. Beefy 27.5x2.8-inch Maxxis Recon tires offer plenty of traction and also help to absorb smaller hits.
Included in this shipment are the much awaited 3540 motors with their slick "UFO" design. These are the replacements for the older square style "H" motors, you may have noticed that this change was implemented last year with the 3525 front and rear motors. As always, we have the motors customized with a 10K NTC thermistor for thermal rollback using the CA3.
In a friction drive motor, a small, solid wheel rotates against the side of the tire in order to drive it. The first motorcycles used the same concept, with a motor mounted above the front wheel. The problem is that the drive rubs at the side of the tire. It's inefficient, and it quickly wears the sidewall away. Tires need to be replaced every couple hundred miles. For this reason, you'll seldom see electric bikes with this type of drive anymore.
Great question… a real world situation from someone doing their best to follow the law but also be realistic about time/distance. What follows is my opinion on the matter based on lots of electric bike riding experience, this is not legal advice. You can probably ride with electric assist across the dirt way with no issues and avoid any negative response that might arise as long as you’re polite to other cyclists and pedestrians and pedal along without going too fast. If someone called you out about it you could easily hop off, walk your bike and explain that you use the assist to help make your commute possible or possibly, like me, you have a knee injury and it’s difficult to pedal through softer terrain like gravel. Another different approach might be to shut the bike off completely before entering the gravel section, you could even take the battery off and put it in a backpack or as mentioned earlier… just walk the bike. Imagine if you had a motorized dirt bike and were just pushing it along a sidewalk… this kind of vehicle definitely is not allowed on sidewalks or most gravel paths like the one you’re describing but if you were escorting it carefully, you’d be honoring the spirit of the law and if an officer or pedestrian jumped out and started questioning you about your “motorized vehicle” it is my feeling that a genuine explanation and apology or request for guidance would go very well. I personally have never had issues riding electric bikes in part because I am thoughtful about how I use them. I do occasionally switch them off and sometimes I get off and walk. I have asked police in many cities across the US what they thought about ebikes and in every case I have received positive interest and support with guidance to ride safe with a helmet and follow traffic laws in the street. I hope this helps and I wish you well, it’s nice that you care enough to ask and I hope you’re treated well by others out on the road. The flip side of this response is that I have been harassed, yelled at and even swerved at by automobiles when riding bicycles and electric bikes. This usually happens in the evening after work lets out when traffic is heavy and I’m riding on the shoulder or in the street (where marked to do so) and I believe it has to do with territory, testosterone and socio-economic standing more so than laws or anything like that.
I eventually got used to it over time, but at first having both kids behind me made the bike feel like it would sway to or fro perilously. I think it was just too much weight to navigate safely, and would be fine with younger kids that didn’t come close to the 120-pound weight limit for the rear cargo area. Overall I’m still a bit partial to a box-style bike if I’m hauling multiple kids and want to be able to see what they’re doing.
Rose Heyer and Josie Tabor of Dept Tech, Department of State Information Center, the Secretary of State and the office of ROCK AND BORGELT, P.C., Attorneys at Law, 24500 FORD ROAD, SUITE 10 DEARBORN HEIGHTS, MI 48127-3106, determined electric bicycles are considered mopeds and need registered and licensed. In order to operate an electric bicycle on public streets, the driver must have a valid operator, chauffeur, or special moped license. However, not all electric bicycles are street legal unless they have the following safety equipment: operating brake light, headlight, and turn signals. The local police department must inspect the bicycle using Form TR-54 which is taken with proof of purchase to the DMV. The fee for the plate is $15 for a three year decal, whereas the fine for no decal is $150 per incident.
Use of and/or registration on any portion of this site constitutes acceptance of our User Agreement (updated 5/25/18) and Privacy Policy and Cookie Statement (updated 5/25/18). Your California Privacy Rights. The material on this site may not be reproduced, distributed, transmitted, cached or otherwise used, except with the prior written permission of Condé Nast. Ad Choices.
Riding a pedal-assisted road bike may seem counterintuitive but during longer training sessions, the minimal addition of power helps prevent overall muscle fatigue and injury. Similarly, those looking to enjoy longer scenic routes will appreciate the general boost an electric drive provides. With a top speed of 28 mph, the Road E+1 uses three power modes to give you ultimate control over your ride and assistance level. A four-point sensory system monitors the pedaling force allowing the motor to amplify your movements seamlessly.
Electric trikes have also been produced that conform to the e-bike legislation. These have the benefit of additional low speed stability and are often favored by people with disabilities. Cargo carrying tricycles are also gaining acceptance, with a small but growing number of couriers using them for package deliveries in city centres.[51][52] Latest designs of these trikes resemble a cross-between a pedal cycle and a small van.[53][54]
In a friction drive motor, a small, solid wheel rotates against the side of the tire in order to drive it. The first motorcycles used the same concept, with a motor mounted above the front wheel. The problem is that the drive rubs at the side of the tire. It's inefficient, and it quickly wears the sidewall away. Tires need to be replaced every couple hundred miles. For this reason, you'll seldom see electric bikes with this type of drive anymore.
"Motor-driven cycle" means any vehicle equipped with two or three wheels, a power source providing up to a maximum of two brake horsepower and having a maximum piston or rotor displacement of 50 cubic centimeters if a combustion engine is used, which will propel the vehicle, unassisted, at a speed not to exceed 30 miles per hour on a level road surface, which does not require clutching or shifting by the operator.[138] The designation is a replacement for "scooter" and "moped;"[139] Vermont doesn't seem to have laws specifically for e-bikes.[140]
The body is made from light and durable aluminum. The handlebar comes with simple controls to let you accelerate, brake, monitor battery life, operate headlights and of course…sound the horn. There’s even an USB point that will let you charge your iPhone or Android on the go. The bike can reach a top speed of 10mph. Feel the wind in your hair as you zoom up and down hills and past all that city traffic…

If a car is at fault in an accident with a bicycle or ebike, their motor vehicle insurance will likely cover your cost for repair and hopefully medical expenses. But what happens if you are at fault, riding an ebike illegally because you did not register it as a Moped? At best, you could be prosecuted under the law. At worst, you could be financially liable for neglect or reckless endangerment via a law suit.
The drivetrain begins with pedals which rotate the cranks, which are held in axis by the bottom bracket. Most bicycles use a chain to transmit power to the rear wheel. A very small number of bicycles use a shaft drive to transmit power, or special belts. Hydraulic bicycle transmissions have been built, but they are currently inefficient and complex.
Electric mountain bikes have garnered a lot of attention for their ability to help riders go higher, further, and faster on the trail. As a result, there have been some impressive new eMTB models to hit the market in recent years, making it easier than ever to head off-road. Our favorite is the Haibike SDURO HardNine, which comes equipped with a 350-watt Bosch Performance CX drive and a 500 watt-hour battery. This gives it a range of up to 70 miles, along with a top speed of 20 mph, which is plenty fast on singletrack.
Another type of electric assist motor, often referred to as the mid-drive system, is increasing in popularity. With this system, the electric motor is not built into the wheel but is usually mounted near (often under) the bottom bracket shell. In more typical configurations, a cog or wheel on the motor drives a belt or chain that engages with a pulley or sprocket fixed to one of the arms of the bicycle's crankset. Thus the propulsion is provided at the pedals rather than at the wheel, being eventually applied to the wheel via the bicycle's standard drive train.

In my experience, there aren’t people out checking on ebike classes and the way you ride has a lot more to do with being stopped than what you are riding. I have never been stopped on an ebike anywhere for any reason. The bigger risk is riding a faster and even more powerful electric bike that would be categorized as a moped without a license and that if you got into an accident, you could be liable for more and charged with driving an unregistered vehicle or something. It’s great that you’re being careful and thinking about how to fit into the community, that alone goes a long way
On the road, it takes only a few turns of the pedals to activate the Vado’s motor and get it up to speed. In Turbo mode — the bike’s highest level of pedal-assist — the Vado reaches speeds of up to 28 miles per hour, after which the electric drive system automatically shuts off to conserve power (and abide by local law). A built-in LED readout on the handlebars allows riders to monitor battery life, check current speed, and track calories burned while also being able to glance at distance traveled. The Turbo Vado Mission Control app (iOS/Android) also connects to the bike via Bluetooth and allows riders to further tune their ride and adjust the bike’s settings.
Electric trikes have also been produced that conform to the e-bike legislation. These have the benefit of additional low speed stability and are often favored by people with disabilities. Cargo carrying tricycles are also gaining acceptance, with a small but growing number of couriers using them for package deliveries in city centres.[51][52] Latest designs of these trikes resemble a cross-between a pedal cycle and a small van.[53][54]
Some of the Rad Wagon’s (small) flaws became apparent once I added more weight to the bike. The integrated rear rack can attach various panniers, platforms, or baskets to cary your cargo, but I was most concerned with hauling my two kiddos to school. Riding the bike with my three year old was a cinch; he held on to the bars in the caboose (available as an accessory add-on) and enjoyed the view. Adding my very tall, almost seven-year-old daughter, however, was a bit more complicated.

EU: EN15194 (EPAC – Electrically Power Assisted Cycles) defines the use pedal-assisted less than 25k/h bikes: "Cycles with pedal assistance which are equipped with an auxiliary electric motor having a maximum continuous rated power of 0.25 kW, of which the output is progressively reduced and finally cut off as the vehicle reaches a speed of 25 km/h or if the cyclist stops pedaling.”


“Changes in production and consumption patterns are a crucial element of the sustainability agenda. Communication between product developers and users, and user integration in product development, can serve as a means for organizational as well as individual learning processes, resulting in sustainable product development. [...] Improved methods, such as INNOCOPE (innovating through consumer-integrated product development), tested in this study with a cycle manufacturer and resulting in a new product, a pedelec, are needed for effective communication, activating consumers and enabling them to promote sustainability goals. Through co-operative product development processes key factors facilitating and obstructing the adoption of sustainable innovations may be identified. Such processes can enhance the emergence and diffusion of sustainable product innovations and different forms and bodies of knowledge can be combined. Integrating users' contextual everyday knowledge of the product with the technical knowledge of companies may lead to mutual learning, technical innovations and changes in consumer behaviour.” (Hoffmann, 2007).


Eight provinces of Canada allow electric power assisted bicycles. In all eight provinces, e-bikes are limited to 500 W output, and cannot travel faster than 32 km/h (20 mph) on motor power alone on level ground.[12] In Alberta prior to July 1, 2009, the limits were 750 W and 35 km/h (22 mph), but presently match federal legislation.[13] Age restrictions vary in Canada. All require an approved helmet. Regulations may or may not require an interlock to prevent use of power when the rider is not pedaling. Some versions (e.g., if capable of operating without pedaling) of e-bikes require drivers' licenses in some provinces and have age restrictions. Vehicle licenses and liability insurance are not required. Generally, they are considered vehicles (like motorcycles and pedal cycles), so are subject to the same rules of the road as regular bicycles. In some cases, regulatory requirements have been complicated by lobbying in respect of the Segway PT.
For people wanting to push the effects of Statorade to the max, the Australian made Hubsinks can clamp on to your motor shell and provide additional cooling fins to shed heat to ambient air. These fit our new MXUS Cassette motors, and the 9C, Crystalyte H, and many others. These are listed on our new store category for motor cooling mods. And like other small products, we try to  keep a stock of 10mL Statorade syringes on Amazon for easy shipping to US customers. They are sold out now but another shipment is inbound. 
Electric bicycle fits under the definition of "moped" under Kentucky law. You don't need tag or insurance, but you need a driver's license. "Moped" means either a motorized bicycle whose frame design may include one (1) or more horizontal crossbars supporting a fuel tank so long as it also has pedals, or a motorized bicycle with a step-through type frame which may or may not have pedals rated no more than two (2) brake horsepower, a cylinder capacity not exceeding fifty (50) cubic centimeters, an automatic transmission not requiring clutching or shifting by the operator after the drive system is engaged, and capable of a maximum speed of not more than thirty (30) miles per hour[43][44] Helmets are required.
A "class 1 electric bicycle," or "low-speed pedal-assisted electric bicycle," is a bicycle equipped with a motor that provides assistance only when the rider is pedaling, and that ceases to provide assistance when the bicycle reaches the speed of 20 miles per hour. (2) A "class 2 electric bicycle," or "low-speed throttle-assisted electric bicycle," is a bicycle equipped with a motor that may be used exclusively to propel the bicycle, and that is not capable of providing assistance when the bicycle reaches the speed of 20 miles per hour. A "class 3 electric bicycle," or "speed pedal-assisted electric bicycle," is a bicycle equipped with a motor that provides assistance only when the rider is pedaling, (no throttle) and that ceases to provide assistance when the bicycle reaches the speed of 28 miles per hour, and equipped with a speedometer. Local government ordinances are allowed to permit or ban any class of electric bicycles on dedicated bicycle paths and trails, with Class 1 & 2 permitted, and Class 3 banned, by default.
The Motan M-150 electric bike is one of the Addmotor’s best selling models. Featuring a 750W high-speed brushless rear hub motor, goes to the top speed of about 25mph. An upgraded 48V 11.6AH Panasonic lithium battery with improved reliability, makes going up a long, steep hills a breeze.  An upgraded 48V 11.6AH Panasonic battery provides improved reliability. This folding bike is designed to fit riders 5’4″-6’4″ and carry a max weight of 300 lbs, making it an ideal option even for larger riders. You can expect to get out 45-55 miles range while using the level one assist. Fully functional pedals also allow you to pedal without motor assist. Collapsible top-tube, frame, and pedals make it portable and easy to store in your car, and unfold in only 10 seconds when you’re ready to use it.
An e-bike is identified as a "motor assisted cycle" (MAC) in British Columbia, which differs from electric mopeds and scooters, which are "limited-speed motorcycles." Motor assisted cycles must: have an electric motor of no more than 500 W; have fully operable pedals; not be capable of propelling the device at a speed greater than 32 km/hr [19.9 mph]. The engine must disengage when (a) the operator stops pedaling, (b) an accelerator controller is released, OR (c) a brake is applied. A driver's license, vehicle registration, and insurance are all not required. A bike helmet must be worn.[22]

I am very pleased with the quality and performance of this electric bike. I find that the twist grip throtle works better for me than the peddle assist low, medium and high settings. It is not necessary to change out of high gear to climb most hills while peddling with the throttle also providing power. The shocks work well on dirt paths and the seat is comfortable. On power alone the bike goes about 15 to 18 mph on flat ground. I have been able to go about 24 miles using combined power and peddling before running out of battery. I assembled this myself.


Play it Safe, Make it Easy – E-bike manufacturers will offer you a large variety of styles, types, colors and utility, but the base specifications will be a bike producing less than 750 watts of power (1 horsepower = 746W) , and have its speed limited to 20mph on motor power alone. The majority of US ebikes meet that specification. Manufacturers do this for their own liability. Going this route assures you that your bike was built and sold legally. As a result, you will have about every privilege that a normal bicycle can expect. However, state and local laws may dictate reduced speeds and limited access to bike paths.
Both land management regulators and mountain bike trail access advocates have argued for bans of electric bicycles on outdoor trails that are accessible to mountain bikes, citing potential safety hazards as well as the potential for electric bikes to damage trails. A study conducted by the International Mountain Bicycling Association, however, found that the physical impacts of low-powered pedal-assist electric mountain bikes may be similar to traditional mountain bikes.[68]
"Electric power-assisted bicycle" means a vehicle that travels on not more than three wheels in contact with the ground and is equipped with (i) pedals that allow propulsion by human power and (ii) an electric motor with an input of no more than 1,000 watts that reduces the pedal effort required of the rider. For the purposes of Chapter 8 of this title, an electric power-assisted bicycle shall be a vehicle when operated on a highway.[65]
The time or distance an electric bike battery will run between chargings is impossible to judge with much accuracy. There are too many variables: terrain, speed, rider weight, bike load (shopping, kids, luggage), and more. However, we can make a few generalizations about an e-bike’s recharge time and overall working life. These generalizations should be used for comparison purposes only.
80% of your personal Carbon Footprint is made up of three main things. How you POWER your House. What you EAT. How you TRANSPORT yourself. There are major changes happening in all three of these areas. In the next 5-10 years, homes will have economical options to incorporate Power Generation, Power Storage and putting Surplus Power back on the Grid. …

In Manitoba Electric Bikes can be classified as a scooter or a moped/mobility vehicle depending on the power of the engine used and its top speed. If the engine on the Electric Bike is less than 50cc and it cannot exceed 50 km per hour the rider is not required to have a motorcycle licence or any specific training.[26] Electric Bikes can be driven by anyone with a Class 5 driver's licence in any stage of the graduated licensing process.[27] A Class 5 Learners Licence requires one to be age 16 (parents consent if under 18) and a visit to a licensing office to pass a vision test and a written knowledge test about the rules of the road and traffic signs.[28]
Several bills have been sponsored to legalize electric bicycles for use on NYS roads, and several have overwhelmingly passed at the committee level, but none of these initiatives has been able to be heard and then passed in the New York State Senate, until 2015. The latest bill S3997, "An act to amend the vehicle and traffic law, in relation to the definition of electric assisted bicycle. Clarifying the vehicle and traffic law to define electric assisted bicycles; establish that electric assisted bicycles, as defined, are bicycles, not motor vehicles; and establish safety and operational criteria for their use." has passed in the Senate for the first time ever in 2015.[116] The related Assembly bill A233 was not brought to a vote in the assembly even though it had passed with little issue in prior years.[117]
Several bills have been sponsored to legalize electric bicycles for use on NYS roads, and several have overwhelmingly passed at the committee level, but none of these initiatives has been able to be heard and then passed in the New York State Senate, until 2015. The latest bill S3997, "An act to amend the vehicle and traffic law, in relation to the definition of electric assisted bicycle. Clarifying the vehicle and traffic law to define electric assisted bicycles; establish that electric assisted bicycles, as defined, are bicycles, not motor vehicles; and establish safety and operational criteria for their use." has passed in the Senate for the first time ever in 2015.[116] The related Assembly bill A233 was not brought to a vote in the assembly even though it had passed with little issue in prior years.[117]

It’s unlikely the Instagram generation ever thought there would be an eBike built with them in mind. Stereotypes of old people riding their e-assisted bikes with cumbersome batteries and questionable frames. Then Lithium Cycles and the Super 73 turned up! Across the last few months, social media has been bustling with talk, influencers, Will Smith … Continue reading Lithium Cycles Super 73: Coming Soon
There's much less of a sensation of the Electrified S2 'fighting back' once you hit 15.5mph, as well. That's helped by the automatic 2-speed gear box, although this does take some getting used to. Because its cogs are very different sizes you can end up with all sorts of cadence problems as it auto-shifts from high back to low. With practice you can avoid this, or of course you could in theory fit a second cog that's closer in size to the first.
The BC Bike Show is the premier cycling and outdoors event in Western Canada and is happening in just 2 weeks on March 2nd and 3rd. We'll be there of course, and in addition to our exhibitor booth we'll also be hosting Cycle Stage to give more public presentations. On Saturday at 11:45 am we'll talk on how to navigate the various motor and battery options available for ebike retrofits, and on Sunday at 2pm we'll be doing a live demonstration of a regular bicycle being converted over to electric assist.
×