It’s unlikely the Instagram generation ever thought there would be an eBike built with them in mind. Stereotypes of old people riding their e-assisted bikes with cumbersome batteries and questionable frames. Then Lithium Cycles and the Super 73 turned up! Across the last few months, social media has been bustling with talk, influencers, Will Smith … Continue reading Lithium Cycles Super 73: Coming Soon
In a friction drive motor, a small, solid wheel rotates against the side of the tire in order to drive it. The first motorcycles used the same concept, with a motor mounted above the front wheel. The problem is that the drive rubs at the side of the tire. It's inefficient, and it quickly wears the sidewall away. Tires need to be replaced every couple hundred miles. For this reason, you'll seldom see electric bikes with this type of drive anymore.
I am very pleased with the quality and performance of this electric bike. I find that the twist grip throtle works better for me than the peddle assist low, medium and high settings. It is not necessary to change out of high gear to climb most hills while peddling with the throttle also providing power. The shocks work well on dirt paths and the seat is comfortable. On power alone the bike goes about 15 to 18 mph on flat ground. I have been able to go about 24 miles using combined power and peddling before running out of battery. I assembled this myself.
Electric-assisted bicycles, also referred to as "e-bikes," are a subset of bicycles that are equipped with a small attached motor. To be classified as an "electric-assisted bicycle" in Minnesota, the bicycle must have a saddle and operable pedals, two or three wheels, and an electric motor of up to 1,000 watts, as well as meet certain federal motor vehicle safety standards. The motor must disengage during braking and have a maximum speed of 20 miles per hour (whether assisted by human power or not). Minn. Stat. §169.011, subd. 27.
Electric powered bicycles slower than 20 km/h without pedaling are legally recognized as a non-mechanically operated vehicle in China. According to "TECHNOLOGY WATCH", this should help promote its widespread use. Electric bicycles were banned in some areas of Beijing from August 2002 to January 2006 due to concerns over environmental, safety and city image issues. Beijing has re-allowed use of approved electric bicycles as of January 4, 2006. Some cities in China still ban electric bikes.
The Dew-E packs functionality and fun into a rather traditional and conservative package. Front and rear fenders, integrated Busch & Müller front and rear lights, and a built-in Abus wheel lock make this a very practical commuter bike. An 11-34, 9-speed cassette and 1.75-inch tires provide versatility: You’ll ride smooth over rough city streets and zip down gravel bike paths with confidence. Front and rear rack mounts also give you the chance to outfit this bike for carrying more cargo or supplies for a longer day on the bike.
Off the back of our wildly successful demo weekend with Haibike a few weeks ago, we have decided to run a recap of our picks for the 2018 Haibike eBike range. Across Haibike’s wide range of eBikes built for all styles of off-road riding, a lot of different technologies have been used. From a mix … Continue reading The Haibike eBike Range 2018 – The Fully Charged Picks
Gearless (Direct-Drive) Hub Motors – Some conversion kits (and bikes) use gearless, direct-drive motors. On this type of motor, the axle that passes through the center of the motor is actually the axle of the motor itself, with the copper windings fixed to the axle. The magnets are mounted to the outer shell of the hub motor. When electricity is applied to the stator a magnetic field is induced that causes the magnets to move. This in turn makes the whole shell of the motor turn and propels the e-bike forward. Even though corrosion will eventually have an impact, this type of motor should last for years since there’s no gearing and no contact between moving parts. They’re also capable of higher top speeds. But since there’s no gears, they have less torque and it requires more power to get the motor up to speed. Most direct-drive hub motors are 350w-500w and reach speeds of 18-25 mph. But more powerful motors can reach speeds of 35+ mph.
The frame of an electric bike also has to be slightly different. The main part of the frame (the bit that supports your weight) is usually made from lightweight aluminum alloy: the lighter the frame, the lighter the weight of the bike overall, and the further it can travel before you need to recharge the batteries. The spokes on the wheel also have to be stronger than the thin spokes on a traditional bicycle. That's because the electric motor in the hub spins the wheel with a lot of turning force (known as torque) and, if the spokes were ordinary lightweight ones, they could bend or buckle.
We Can Build It. Built by hand in Pennsylvania, mostly by Harry and Alec. Custom Wheelbuilding Some people don't know that we build every one of our wheels here by hand in Pennsylvania. This lets us control each step of the process, ensuring that the spokes are uniform, straight, and undamaged, allowing us to apply spoke-prep to the spokes, oil to the nipple seats, and inspect the rims before we use them. We get the tension, dish, lateral and radial trueness dialed in to our standards and know it's a good wheel before it goes out the door.
J. K. Starley's company became the Rover Cycle Company Ltd. in the late 1890s, and then simply the Rover Company when it started making cars. Morris Motors Limited (in Oxford) and Škoda also began in the bicycle business, as did the Wright brothers. Alistair Craig, whose company eventually emerged to become the engine manufacturers Ailsa Craig, also started from manufacturing bicycles, in Glasgow in March 1885.