EU: EN15194 (EPAC – Electrically Power Assisted Cycles) defines the use pedal-assisted less than 25k/h bikes: "Cycles with pedal assistance which are equipped with an auxiliary electric motor having a maximum continuous rated power of 0.25 kW, of which the output is progressively reduced and finally cut off as the vehicle reaches a speed of 25 km/h or if the cyclist stops pedaling.”
Photo: This typical electric bicycle, a Sanyo Eneloop (now discontinued), had a range of about 30–55 km (17–35 miles) and a top speed of around 24 km/h (15 mph). Note the 250-watt hub motor on the front wheel and the 5.7Ah lithium-ion battery pack (black, marked "Sanyo," just in front of the back wheel). Picture by kind permission and courtesy of Richard Masoner, originally published on Flickr under a Creative Commons (CC BY-SA 2.0) licence.

There are two basic categories of electric bike, and their uses don't offer equal crossover value. The first category is essentially a normal bicycle that has been outfitted with an electric motor. These bikes are the same size as a standard bicycle, and handle almost identically, save for the obvious benefit of added motive power thanks to a motor and battery.


Are there any guidelines you could give on what is legal in Federal Parks that have duel use pedestrian and bike paths. I was recently told that E bikes are not allowed on a Federal trail even though much faster 10 and 20 speed bicycles are common. I also stated that I have a disability which prevents me from walking or biking very far but was still told my bike was not allowed. I should also add that my bike has a top speed of about 15 and is 250 watts.
This Saturday, Oct. 7, Tim Sway will showcase his “UpTriCycle” at the Greater Hartford Mini Maker Faire. Sway calls the UpTricycle an “off grid, electric, solar charging mobile maker space and carrier for upcycling makers.” He uses minimal tools and footprints in his creation for unlimited potential. On his YouTube page, Sway made a comparison video between a gas-powered trike and an electric trike. He purchased a gas-powered trike first, and then converted that same trike to electric with our E-Bike Conversion Kit. After testing out both designs and comparing the two, Sway decided that the electric tricycle was superior...

Historically, materials used in bicycles have followed a similar pattern as in aircraft, the goal being high strength and low weight. Since the late 1930s alloy steels have been used for frame and fork tubes in higher quality machines. By the 1980s aluminum welding techniques had improved to the point that aluminum tube could safely be used in place of steel. Since then aluminum alloy frames and other components have become popular due to their light weight, and most mid-range bikes are now principally aluminum alloy of some kind.[where?] More expensive bikes use carbon fibre due to its significantly lighter weight and profiling ability, allowing designers to make a bike both stiff and compliant by manipulating the lay-up. Virtually all professional racing bicycles now use carbon fibre frames, as they have the best strength to weight ratio. A typical modern carbon fiber frame can weighs less than 1 kilogram (2.2 lb).


To be honest, this bike is really designed for city commuters or kids riding around the suburbs. The fact that it’s foldable will let you carry it on the bus, on the train or even on the plane. It’s just not designed for heavy riding, long distances or tough terrains. If you want something sleek and fabulous at a fraction of the cost of most other e-bikes, this baby’s for you.
The benefits don’t stop at the physical, however. Our daily lives are spent glued to computer and phone screens, and even if you choose to accept that as an inevitable wave of the future, your mind still needs a release from all that toxic screen time. Because a bike moves more slowly than a car, while also giving you much better sight lines and more direct exposure to the sun, a nice ride — even through city streets — will put you more in touch with nature. Getting in touch with your natural environment can drastically reduce stress levels, which is why biking to and from work is such a good idea: no matter how frustrating your day at the office was, you can let it all go on the enjoyable cycling trip home.
If you're more concerned with conquering the countryside than the commute, Cyclotricity's Stealth is the one for you. It's a full-size mountain bike, with aggressive tyres and suspension on the front forks to absorb the rocks and bumps on the trails. It's comfortable to ride, and its motor can either give you assistance while you ride, or you can just hit the throttle to rocket over hills with no effort on your part.

The motor isn’t insanely powerful, but it gets you up to full speed quickly enough. I never felt like the bike was underpowered. The motor does make more noise than a lot of other hub motor bikes I’ve ridden though. There’s a definite whirrr to the motor caused by the internal plastic gears. While all geared motors will have some level of gear noise, this one stuck out more to me than others.

Fast and fun on the trail, the SDURO HardNine handles rough terrain with ease, while its large tires roll over most obstacles without missing a beat. The pedal assist makes for quick, energy-saving climbing and the bike descends surprisingly well, too. Its front suspension provides a nice level of cushion on bumpy trails and while we missed having a full-suspension on this model, that would have added additional weight and costs.


Historically, women's bicycle frames had a top tube that connected in the middle of the seat tube instead of the top, resulting in a lower standover height at the expense of compromised structural integrity, since this places a strong bending load in the seat tube, and bicycle frame members are typically weak in bending. This design, referred to as a step-through frame or as an open frame, allows the rider to mount and dismount in a dignified way while wearing a skirt or dress. While some women's bicycles continue to use this frame style, there is also a variation, the mixte, which splits the top tube laterally into two thinner top tubes that bypass the seat tube on each side and connect to the rear fork ends. The ease of stepping through is also appreciated by those with limited flexibility or other joint problems. Because of its persistent image as a "women's" bicycle, step-through frames are not common for larger frames.
Cargo bikes and city bikes are common in the e-bike space, but until recently we haven’t seen that many performance road bikes. The Giant Road E+1 is a pedal-assist performance road bike that’s made for more than just commuting; the powerful motor can crank you up to 28 mph very quickly on the highest setting so you can rip the flats, join your local group ride, or blast through the mountains with far less effort than a traditional road bike. It won’t feel like a 16-pound race bike when you lean it into high-speed turns, but the endurance-oriented geometry allows for an aggressive position on the bike and keeps it nimble and agile at high speed.
Use of and/or registration on any portion of this site constitutes acceptance of our User Agreement (updated 5/25/18) and Privacy Policy and Cookie Statement (updated 5/25/18). Your California Privacy Rights. The material on this site may not be reproduced, distributed, transmitted, cached or otherwise used, except with the prior written permission of Condé Nast. Ad Choices.

The Footloose has no chain, however -- it's entirely electrically driven. It takes very little effort to get to your destination, meaning you arrive at work without having broken a sweat. The downside is that when you run out of power, you're not going anywhere. And pedalling from a standstill, waiting for the motor to kick in, is an odd sensation that takes some getting used to.


Under New Jersey law a motorized bicycle is "a pedal bicycle having a helper motor characterized in that either the maximum piston displacement is less than 50 cc, the motor is rated at no more than 1.5 brake horsepower, or it is powered by an electric drive motor and the bicycle is capable of a maximum speed of no more than 25 miles per hour on a flat surface."[107] This would include E-bikes, meaning they must be titled and registered. However, only Mopeds approved by Motor Vehicle Services can be titled and registered.
Since 2000, Canada's Motor Vehicle Safety Regulations (MVSR) have defined Power Assisted bicycles (PABs) as a separate category, and which require no license to operate. PABs are currently defined as a two- or three-wheeled bicycle equipped with handlebars and operable pedals, an attached electric motor of 500W or less, and a maximum speed capability of 32 km/h from the motor over level ground. Other requirements include a permanently affixed label from the manufacturer in a conspicuous location stating the vehicle is a power-assisted bicycle under the statutory requirements in force at the time of manufacture.[14][15] All power-assisted bicycles must utilize an electric motor for assisted propulsion.
A KS LEV Integra dropper post, 130mm of front and rear travel, 27.5-inch wheels, and trail-grabbing 2.8-inch tires make this pedal-assist mountain bike a great option if you want to climb farther to shred longer, but don’t want to lug your bike uphill for ages. The 250-watt motor, placed slightly farther forward than most other bikes to optimize weight distribution and handling, provides a nice boost so you can enjoy the ride up and not be too gassed when you get to the top.
While we won't be there in person, a number of vehicles will be at the show featuring the new Grin products like the GMAC Hub Motors, RH212 direct drive motors, All Axle hubs, and the Baserunner and Phaserunner_L10 controllers.  If you're lucky enough to attend then check out Booth A.18 and Booth 3.12 for some velomobiles and cargo vehicles running this gear.  
A response to an inquiry made to the Mass DOT/RMV indicates that Massachusetts does recognize the federal low speed electric bicycle Federal Law (15 U.S.C. § 2085) and interprets that to mean these ebikes do not require license or registration. However, some of the materials available on the RMV website do not distinguish between "Motorized Bicycle" and low power ebikes. One form, Bicycle Conversion to Motorized Bike, does document the exemption of low power ebikes.[100]

The Riese & Müller Load Touring HS is billed as “the ultimate minivan of e-bikes,” and it holds up to that claim. With a low center of gravity (aided by the 20-inch front and 26-inch rear wheels), the Load is easy to handle. Tektro hydraulic disc brakes add control, and front and rear suspension provide comfort. The Bosch motor offers an assist up to 275 percent of your effort until you hit 28 mph, when it cuts out. Two 500Wh batteries give you 12 hours or more of range at full power. It’s capable of toting up to 220 pounds of pets, people, and less-animate cargo. R&M also sells a double child seat for kids up to age 6 and a child-seat fastener for your youngest passengers.

Bicycle brakes may be rim brakes, in which friction pads are compressed against the wheel rims; hub brakes, where the mechanism is contained within the wheel hub, or disc brakes, where pads act on a rotor attached to the hub. Most road bicycles use rim brakes, but some use disk brakes.[49] Disc brakes are more common for mountain bikes, tandems and recumbent bicycles than on other types of bicycles, due to their increased power, coupled with an increased weight and complexity.[50]
In the early 1860s, Frenchmen Pierre Michaux and Pierre Lallement took bicycle design in a new direction by adding a mechanical crank drive with pedals on an enlarged front wheel (the velocipede). This was the first in mass production. Another French inventor named Douglas Grasso had a failed prototype of Pierre Lallement's bicycle several years earlier. Several inventions followed using rear-wheel drive, the best known being the rod-driven velocipede by Scotsman Thomas McCall in 1869. In that same year, bicycle wheels with wire spokes were patented by Eugène Meyer of Paris.[22] The French vélocipède, made of iron and wood, developed into the "penny-farthing" (historically known as an "ordinary bicycle", a retronym, since there was then no other kind).[23] It featured a tubular steel frame on which were mounted wire-spoked wheels with solid rubber tires. These bicycles were difficult to ride due to their high seat and poor weight distribution. In 1868 Rowley Turner, a sales agent of the Coventry Sewing Machine Company (which soon became the Coventry Machinists Company), brought a Michaux cycle to Coventry, England. His uncle, Josiah Turner, and business partner James Starley, used this as a basis for the 'Coventry Model' in what became Britain's first cycle factory.[24]
Bicycles can be categorized in many different ways: by function, by number of riders, by general construction, by gearing or by means of propulsion. The more common types include utility bicycles, mountain bicycles, racing bicycles, touring bicycles, hybrid bicycles, cruiser bicycles, and BMX bikes. Less common are tandems, low riders, tall bikes, fixed gear, folding models, amphibious bicycles, cargo bikes, recumbents and electric bicycles.

Under the statute, mopeds must be registered. To be registered under Hawaii law a moped must bear a certification label from the manufacturer stating that it complies with federal motor vehicle safety standards (FMVSS). A moped must also possess the following equipment approved by the D.O.T. under Chapter 91: approved braking, fuel, and exhaust system components; approved steering system and handlebars; wheel rims; fenders; a guard or protective covering for drive belts, chains and rotating components; seat or saddle; lamps and reflectors; equipment controls; speedometer; retracting support stand; horn; and identification markings.

Government regulation is written and administered with a broad, dull, painful axe. Regulations do not mix well with independent, maverick, DIY programs either. Vehicle regulations get started when there is either a visible tragedy, or a rising conflict with the status quo (like the SFO scooters program). The ebike community cannot afford a deadly accident especially if it involves others and the ebike or ebike rider are at fault. The Ebike community is up against a tough status quo that consists of pedestrians, motor vehicle traffic, the large well-funded and battle tested regular bicycle community, and the environment (especially for MTB riding and off-road use).


Electric bicycles use batteries as a source of power and a quiet DC motor as a driving mechanism. On most e-bikes the motor is built directly into the wheel (known as a hub motor) and the batteries are discreetly hidden in the rear rack or frame. Electric bikes can be operated just like normal bicycles, but they can also be power-driven by a throttle or pedaled with the help of pedal-assist (PAS or pedelec).
Great bike. Easy to assemble by yourself but if you have a rack let pros do it. No charge for that. Contacted the Addmotor people a few times and they got back quickly even on weekends. Great service. Bike is solid as a rock and excellent components. Only drawback is lack of fenders which I hope someone can manufacture. I would buy again in a nano second!
The Wavecrest Tidalforce M-750 was based on The original military experimental M-313 model. The M-313/M-750X was the first electric bike to be made and tested by Wavecrest Labs. It is based on a design developed for the Defense Advanced Research Projects Agency (DARPA) that was meant to allow zero-heat long distance troop movements for the United States Marine Corps in Afghanistan. The rear wheel in-hub motor and 36 volt/8ah front-hub battery were mounted onto a standard Montague Bicycles Paratrooper Bicycle frame. The 1000 watt rear hub motor had no set speed restriction, but was limited to about 25-32 (depending on load weight) MPH on a flat course. The distance the bike traveled on a single charge ranged from 15 miles (heavier load with no pedaling) to about 25 miles (vigorous assisted pedaling with less hill climbing).

Conversion kits, on the other hand, are sold and installed separately on traditional bicycles. They are harder to setup and conceal, and require some basic mechanical ability and a little bit of ‘elbow grease’ to install. The advantage of conversion kits is that you can choose almost any standard bicycle, and you have the freedom to change or upgrade components as you go. A conversion kit will also allow you to achieve higher power and speed ratings that are not possible on most pre-built electric bike models. Kits are great for tall or heavy riders because they can opt for a larger bike, with higher power and weight carrying capacity. People living in hilly terrain may require the additional torque to handle extremely large inclines. For people who prefer a specific bike model or just love to go faster, a conversion kit offers enormous flexibility.
To legally operate a motorized bicycle or electric-assisted bicycle the operator must be licensed, the motorized bicycle/electric-assisted bicycle must be registered in one of the following definitions and meet the required safety equipment. If the operator or the motorized bicycle/electric- assisted bicycle does not meet all requirements, they will not be legal for street/highway use (including the sidewalk).To qualify as a motorized bicycle under state law they need to have motor of a piston displacement capacity of 50 cubic centimeters or less, maximum of two brake horsepower, maximum speed of not more than Template:Convert on a flat surface, fully operable pedals for human propulsion are not required, but may be a part of the machine.
In China, e-bikes currently come under the same classification as bicycles and hence don't require a driver's license to operate. Previously it was required that users registered their bike in order to be recovered if stolen, although this has recently been abolished. Due to a recent rise in electric-bicycle-related accidents, caused mostly by inexperienced riders who ride on the wrong side of the road, run red lights, don't use headlights at night etc., the Chinese government plans to change the legal status of illegal bicycles so that vehicles with an unladen weight of 20 kg (44 lb) or more and a top speed of 30 km/h (19 mph) or more will require a motorcycle license to operate, while vehicles lighter than 20 kg (44 lb) and slower than 30 km/h can be ridden unlicensed. In the southern Chinese cities of Guangzhou, Dongguan and Shenzhen, e-bikes, like all motorcycles, are banned from certain downtown districts. There are also bans in place in small areas of Shanghai, Hangzhou and Beijing. Bans of "Scooter-Style Electric Bikes" (SSEB) were however cancelled and in Shenzhen e-bikes may be seen on the streets nowadays (2010–11).
"Medical Exemptions" are also a standard right in the State of Texas for motorcycles & even bicyclists. Through Texas's motorcycle helmet law (bicycle helmet laws from city ordinances), it is only required for those 21 years old or younger to wear a helmet. However, a medical exemption, [59][60][61][62][63][64] written by a certified licensed medical physician or licensed chiropractor, which exempts one from wearing a helmet, can be used for bicyclists if helmets are required.

Electric Bicycles are defined by the California Vehicle Code [32][33]. In summary, electric bicycles are to be operated like conventional bicycles in California. There are several exceptions to this. A person must be at least 16 years old, and anyone riding an electric bicycle must wear a bicycle helmet. The e-bikes must have an electric motor that has a power output less than 1,000 watts, is incapable of propelling the device at a speed of more than 20 miles per hour on level ground, is incapable of further increasing the speed of the device when human power is used to propel the motorized bicycle faster than 20 miles per hour, operates in a manner so that the electric motor is disengaged or ceases to function when the brakes are applied, or operates in a manner such that the motor is engaged through a switch or mechanism that, when released, will cause the electric motor to disengage or cease to function.
In addition the specific wording of the law may or may not prohibit the use of a "mid-drive" or "crank-drive" motor set-up where the motor drives the rear wheel of the bicycle through the existing chain drive of a bicycle that has multiple gears depending on several points of interpretation of the law. Specifically the interpretation of the wording, "does not require clutching or shifting by the operator after the drive system is engaged". A "mid-drive" or "crank-drive" motor set-up on an electric bicycle does indeed allow the operator to change gears in the power drive system between the motor and the rear wheel of the bicycle. Whether or not such a mechanism which allows the operator to change gears satisfies the wording that requires the operator to change gears is a matter of legal interpretation by the courts. Just as "shall issue" and "may issue" (as in laws governing the issuing licenses) in application of the law have two different meanings (in the first case if you meet the requirements they have to give you the license and in the second they don't have to if they decide not to even if you meet the requirements for the license) whether or not "does not require shifting" outlaws electric bicycles where shifting is possible but is not necessarily required is a matter of interpretation. Thus the legality of electric bicycles equipped with a "mid-drive" or "crank-drive" motor set-up in the U.S. state of Montana is not clearly defined.

A KS LEV Integra dropper post, 130mm of front and rear travel, 27.5-inch wheels, and trail-grabbing 2.8-inch tires make this pedal-assist mountain bike a great option if you want to climb farther to shred longer, but don’t want to lug your bike uphill for ages. The 250-watt motor, placed slightly farther forward than most other bikes to optimize weight distribution and handling, provides a nice boost so you can enjoy the ride up and not be too gassed when you get to the top.


The release of Garmin’s new Edge 520 Plus GPS bike computer made a big splash in the world of cycling. It was an impressive upgrade, likely a response to increasing competition from the likes of Wahoo. But the Garmin Edge 520 Plus upgrade has caused a little confusion, because it seems to offer the same mapping and navigation capabilities as the more expensive Edge 820 and 1030. We clear up the confusion with two in-depth posts, Garmin Edge 520 vs 520 Plus, and Garmin Edge 1030 vs 820 vs 520 Plus.
The environmental credentials of e-bikes, and electric / human powered hybrids generally, have led some municipal authorities to use them, such as Little Rock, Arkansas with their Wavecrest electric power-assisted bicycles or Cloverdale, California police with Zap e-bikes. China’s e-bike manufacturers, such as Xinri, are now partnering with universities in a bid to improve their technology in line with international environmental standards, backed by the Chinese government who is keen to improve the export potential of the Chinese manufactured e-bikes.[67]
My homeowners (State Farm) covers bikes , but assumes $500 per bike. They will add the bikes as personal property, but the premium is excessive (about $300/year per bike, and we have four bikes). I did increase our personal umbrella liability coverage, and it covers us if family members any sort of accident on our e-bikes that injures us or others or others' property, though only covers $500 each for our own bikes (under the homeowners coverage). It was not very expensive to increase the umbrella policy (as it resulted also in a reduced rate on our car insurance).
Off the back of our wildly successful demo weekend with Haibike a few weeks ago, we have decided to run a recap of our picks for the 2018 Haibike eBike range. Across Haibike’s wide range of eBikes built for all styles of off-road riding, a lot of different technologies have been used. From a mix … Continue reading The Haibike eBike Range 2018 – The Fully Charged Picks
But in Great Britain, the European Union definition is applicable, and the tighter restrictions of the Electrically Assisted Pedal Cycle Regulations 1983 (including a 200 kg weight limit on solo bicycles) were removed on 6 April 2015 by the Electrically Assisted Pedal Cycles (Amendment) Regulations 2015.[48][49] Riders must be at least 14 years of age, but no driving licence is required.
In Quebec power-assisted bicycles are often classified similarly to standard pedal bicycles. They do not have to meet the conditions defined within the Canadian Motor Vehicle Safety Regulations (they are not classed as "motor vehicles"), but they do have to comply with federal regulations that define Power Assisted Bicycles. The Quebec Highway Safety Code defines a power-assisted bicycle as a bicycle with an electric motor. PABs are permitted on the road in the province of Quebec.
Bicycles were introduced in the late 19th century in Europe, and by the early 21st century, more than 1 billion were in existence at a given time.[1][2][3] These numbers far exceed the number of cars, both in total and ranked by the number of individual models produced.[4][5][6] They are the principal means of transportation in many regions. They also provide a popular form of recreation, and have been adapted for use as children's toys, general fitness, military and police applications, courier services, bicycle racing and bicycle stunts.
The Tidalforce Electric Bicycle was an electric bicycle manufactured by Wavecrest Labs from 2003 until the company went out of business in 2006. All models of Wavecrest Tidalforce electric bikes have a 36 volt electric hub motor built into the rear wheel hub and a 36 volt battery pack built into the front wheel hub. Wavecrest Labs manufactured three models of Tidalforce bikes: The Wavecrest Tidalforce M-750, the S-750 Traditional hard tail mountain bike and the iO-750 Cruiser. Any of the three bikes with an X suffix denotes that the motor is a 1000 watt motor without a set speed restriction as compared to the speed limited 750 watt version.
The other motor is the G311, a front equivalent to the wonderfully silent G310 rear motors we introduced late last year. This motor will be replacing the G01 hub for our front mini geared kits. It's a tad lighter (2.3kg), much quieter (spiral gears!), but still has the features from the G01 that we loved. That means a side cable exit, ISO disk rotor compatibility, and 10mm round axle.
The $3,099 MSRP is a bit daunting if you've not shopped for high-end bikes before, but it compares favorably with, say, Trek's electric bike lineup. That said, you can get a solid urban/commuter bike without a motor for well under $1,000. You can even score an e-bike for under a grand, but you'll likely be looking at a battery range of less than 40 miles, along with lower-quality components.
Several bills have been sponsored to legalize electric bicycles for use on NYS roads, and several have overwhelmingly passed at the committee level, but none of these initiatives has been able to be heard and then passed in the New York State Senate, until 2015. The latest bill S3997, "An act to amend the vehicle and traffic law, in relation to the definition of electric assisted bicycle. Clarifying the vehicle and traffic law to define electric assisted bicycles; establish that electric assisted bicycles, as defined, are bicycles, not motor vehicles; and establish safety and operational criteria for their use." has passed in the Senate for the first time ever in 2015.[116] The related Assembly bill A233 was not brought to a vote in the assembly even though it had passed with little issue in prior years.[117]
The definition was clearly written with gasoline-powered pedalcycles in mind. The requirement of an automatic transmission is troublesome for those who just want to add an electric-assist motor to a bicycle, for almost all bicycles have transmissions consisting of chains and manually shifted sprockets. The registration form asks for a VIN, making it difficult to register some foreign-made ebikes. The fine for riding an unregistered electric bike is approximately $160.00 per event as of 2007.

Simple, convenient, cheap, and economical—bicycles are one of the world's favorite forms of transportation. But they're not for everyone. They can be hard to pedal up and down hills or with heavy loads, and elderly or disabled people may find them impossible to manage. In the last few years, a new generation of electric bicycles has begun to revolutionize our idea of environmentally friendly transportation. These new cycles have all the convenience of cars with all the simple economy of ordinary cycles. Let's take a closer look at how they work.
The 1968 Vienna Convention on Road Traffic of the United Nations considers a bicycle to be a vehicle, and a person controlling a bicycle (whether actually riding or not) is considered an operator. The traffic codes of many countries reflect these definitions and demand that a bicycle satisfy certain legal requirements before it can be used on public roads. In many jurisdictions, it is an offense to use a bicycle that is not in a roadworthy condition.[citation needed]
Under New Jersey law a motorized bicycle is "a pedal bicycle having a helper motor characterized in that either the maximum piston displacement is less than 50 cc, the motor is rated at no more than 1.5 brake horsepower, or it is powered by an electric drive motor and the bicycle is capable of a maximum speed of no more than 25 miles per hour on a flat surface."[107] This would include E-bikes, meaning they must be titled and registered. However, only Mopeds approved by Motor Vehicle Services can be titled and registered.
Perhaps the cleverest thing of all about the Electric Brompton is that despite all the extra stuff, it folds up exactly the same as the non-powered variety. It's so simple, and unlike certain folding bikes we could mention, what you're left with is a genuinely small thing, rather than something that's about the size of a bike with the front wheel taken off.
×