When last checked, no E-bikes satisfied this requirement, so ebikes cannot be registered in New Jersey.[108] However, NJ Bill A2581, introduced March 22, 2010, would permit the use of low-speed electric bicycles upon the roadways and bicycle paths in NJ, where a low-speed electric bicycle is defined as a two-wheeled vehicle with fully operable pedals for human propulsion and an electric motor of less than 100 pounds and 750 watts, whose maximum speed on a paved level surface is less than 20 miles per hour.[109] The bill has been referred to the state's Assembly Transportation, Public Works and Independent Authorities Committee.[110]
Electric bicycles are considered as "bicycles" under Montana law as the law defines bicycles in a two part definition where the first part of the definition describes a conventional bicycle propelled solely by human power and the second part of the definition describes a bicycle equipped with an independent power source for propulsion in addition to foot pedals to permit muscular propulsion. (Montana Code 61-8-102).[104]
From what we could tell from the launch photos, the bikes have 16x1 3/8-inch wheels, chain drive, an internally geared hub, and hydraulic disc brakes. They’re rounded out by full-coverage fenders, reflective-sidewall tires, ergonomic grips, a kickstand, and a bell. The company says the sleek, single-size aluminum frame fits riders between 5 feet and 6 feet tall.
Maybe the most confusing legal issue facing e-bike riders today is the difference between a bike lane and bike path. A bike lane is a marked section of roadway shared with motor vehicles. Bike paths pretty much universally prohibit the use of motorized vehicles. Still, you will need to research your area. As an example: “A path near our office specifically says “no motorized bicycles.” Yet, when we tracked down an employee who claimed to work enforcement on the path, he said that our e-bike was allowed.”8
Controllers for brushless motors: E-bikes require high initial torque and therefore models that use brushless motors typically have Hall sensor commutation for speed and angle measurement. An electronic controller provides assistance as a function of the sensor inputs, the vehicle speed and the required force. The controllers generally allow input by means of potentiometer or Hall Effect twist grip (or thumb-operated lever throttle), closed-loop speed control for precise speed regulation, protection logic for over-voltage, over-current and thermal protection. Bikes with a pedal assist function typically have a disc on the crank shaft featuring a ring of magnets coupled with a Hall sensor giving rise to a series of pulses, the frequency of which is proportional to pedaling speed. The controller uses pulse width modulation to regulate the power to the motor. Sometimes support is provided for regenerative braking but infrequent braking and the low mass of bicycles limits recovered energy. An implementation is described in an application note for a 200 W, 24 V Brushless DC (BLDC) motor.[43]

Hub motors are sold as either geared or direct drive: Geared hubs are preferred for hill climbing ability and zero drag when coasting, while DD hubs are more durable and suitable for high speed. Extreme hill climbing and high torque applications (fatbikes, hauling cargo, popping wheelies) usually requires a mid drive, which is covered in the motor section below. Ebike battery packs from the listed suppliers are generally compatible with kits from any supplier, at worst you may need a different connector, which can be easily replaced. You probably want a battery pack that is 36, 48, or 52 volts, depending on whether you prefer lower price and longer range or a higher topspeed. DIY lipo battery packs can be built cheaply but doing so can be a fire hazard so actual packs are recommended. All hub motors above 24 V should be installed with torque arms for safety.

Electric bikes are considered motorcycles in Hong Kong, and therefore need type approval from the Transport Department, just as automobiles. All electric bikes available in Hong Kong fail to meet the type approval requirement, and the Transport Department has never granted any type approval for an electric bike, making all electric bikes effectively illegal in Hong Kong. Even if they got type approval, the driver would need a motorcycle driving license to ride.[35] As a side note, Hong Kong doesn't have a moped vehicle class (and therefore no moped driving license), and mopeds are considered motorcycles too.


Mid-mounted system means that the electric motor is not built into the wheel but is usually mounted near (often under) the bottom bracket shell. Mid-drive systems tend to feel more like a normal bike, since they drive the pedals, just like your legs, and those who frequently climb long, steep hills tend to prefer mid-drive systems for their ability to handle long climbs. As they can leverage the bicycles lowest gears for climbs, mid drive systems can also leverage the high gears to reach higher speeds on flat areas than a hub system. The mid-drive motor drives the crank, instead of the wheel itself, which multiplies its power and allows it to better take advantage of the bike’s existing gears. If the rider changes the gears appropriately, the motor can turn closer to its ideal rotations per minute which makes a huge difference while climbing hills, so this is a perfect option for those who love mountain biking.
The Alpha has a  36V Brose 50W motor which is fueled by a “bridging” lithium-ion battery with 150 Wh of capacity, which is charged by the onboard 150 W PEM Hydrogen fuel cell. The fuel cell is fueled by a 2 litre compressed hydrogen gas cylinder, which can be refilled in about 2 minutes at a filling station.  In terms of cost per charge, this is likely to be more than a standard electric bike, however, the convenience of faster recharging may make it suitable for some riders, particularly commercial fleet operators using ebikes on shifts for several riders.

Under the Guide Section of EBR, Court has written a full article, dedicated to the new classification approach, which was initiated by the BPSA (Bicycle Product Suppliers Association), supported by PeopleForBikes, and then Calbikes. The initiative was meant to be pro-active with ebike legislation, to establish self-imposed, measurable, distinct classes of electric bikes before states start hearing about anecdotal problems and potentially overreact to the technology with wide sweeping limitations.

You are not allowed to drive S-Pedelecs in France even if they are registered legally in your country (e.g. Germany or Switzerland). In other words, if you plan to take your 45h bike that is legal in your country on vacation in another where it is not, you may violate traffic law. Remove the license plate or don't do it. People who commute between countries, are known to hack removable plates with magnets ...
Even the humble bicycle hasn't escaped the clutches of modern technology. A whole herd of new e-bikes with electric motors are taking to our cities' streets. Adding a motor to a standard cycle does ramp up the price significantly, but it takes much of the effort out of cycling, making your commute to the office a sweat-free experience and allowing you to sit back and enjoy your suburban cruise.
The great majority of modern bicycles have a frame with upright seating that looks much like the first chain-driven bike.[7][8][9] These upright bicycles almost always feature the diamond frame, a truss consisting of two triangles: the front triangle and the rear triangle. The front triangle consists of the head tube, top tube, down tube, and seat tube. The head tube contains the headset, the set of bearings that allows the fork to turn smoothly for steering and balance. The top tube connects the head tube to the seat tube at the top, and the down tube connects the head tube to the bottom bracket. The rear triangle consists of the seat tube and paired chain stays and seat stays. The chain stays run parallel to the chain, connecting the bottom bracket to the rear dropout, where the axle for the rear wheel is held. The seat stays connect the top of the seat tube (at or near the same point as the top tube) to the rear fork ends.
Yes, there are less expensive ebikes on the market but most come with a few serious caveats. The Espin Sport delivers on the full promise of an electric bike, but in a more affordable fashion. This bike isn’t going to tow you around for a 60-mile round-trip endeavor but those seeking their first ebike will get plenty of return on their investment with this model.
At the end of the day, it’s probably best to spend as much as you can to get the bike with the most range that folds up the smallest. Once these puppies run out of juice, they tend to be much harder to pedal than their non-electric counterparts, mainly due to their increased weight, so keep an eye out for lighter models if you know you’re the type to overextend a biking trip. Other features to look out for include racks to help you carry important materials, charging time, and, of course, safety implements like lights and reflectors.
Electric Bicycles are defined by the California Vehicle Code [32][33]. In summary, electric bicycles are to be operated like conventional bicycles in California. There are several exceptions to this. A person must be at least 16 years old, and anyone riding an electric bicycle must wear a bicycle helmet. The e-bikes must have an electric motor that has a power output less than 1,000 watts, is incapable of propelling the device at a speed of more than 20 miles per hour on level ground, is incapable of further increasing the speed of the device when human power is used to propel the motorized bicycle faster than 20 miles per hour, operates in a manner so that the electric motor is disengaged or ceases to function when the brakes are applied, or operates in a manner such that the motor is engaged through a switch or mechanism that, when released, will cause the electric motor to disengage or cease to function.

Under the statute, mopeds must be registered. To be registered under Hawaii law a moped must bear a certification label from the manufacturer stating that it complies with federal motor vehicle safety standards (FMVSS). A moped must also possess the following equipment approved by the D.O.T. under Chapter 91: approved braking, fuel, and exhaust system components; approved steering system and handlebars; wheel rims; fenders; a guard or protective covering for drive belts, chains and rotating components; seat or saddle; lamps and reflectors; equipment controls; speedometer; retracting support stand; horn; and identification markings.
As of May 19, 2009, Nevada amended its state transportation laws to explicitly permit electric bicycles to use any "trail or pedestrian walkway" intended for use with bicycles and constructed with federal funding, and otherwise generally permits electric bicycles to be operated in cases where a regular bicycle could be. An electric bicycle is defined as a two- or three-wheeled vehicle with fully operable pedals with an electric motor producing up to 1 gross brake horsepower and up to 750 watts final output, and with a maximum speed of up to 20 miles per hour on flat ground with a 170 pound rider when powered only by that engine. (AB441, amending NRS 480, 482 and other sections)
Every person riding a bicycle, electric personal assistive mobility device, electric power-assisted bicycle, moped, or an animal or driving an animal on a highway shall be subject to the provisions of this chapter and shall have all of the rights and duties applicable to the driver of a vehicle, unless the context of the provision clearly indicates otherwise.
The bicycle was recognized by 19th-century feminists and suffragists as a "freedom machine" for women. American Susan B. Anthony said in a New York World interview on February 2, 1896: "I think it has done more to emancipate woman than any one thing in the world. I rejoice every time I see a woman ride by on a wheel. It gives her a feeling of self-reliance and independence the moment she takes her seat; and away she goes, the picture of untrammelled womanhood."[74]:859 In 1895 Frances Willard, the tightly laced president of the Woman’s Christian Temperance Union, wrote A Wheel Within a Wheel: How I Learned to Ride the Bicycle, with Some Reflections by the Way, a 75-page illustrated memoir praising "Gladys", her bicycle, for its "gladdening effect" on her health and political optimism.[72] Willard used a cycling metaphor to urge other suffragists to action.[72]
From the beginning and still today, bicycles have been and are employed for many uses. In a utilitarian way, bicycles are used for transportation, bicycle commuting, and utility cycling. It can be used as a 'work horse', used by mail carriers, paramedics, police, messengers, and general delivery services. Military uses of bicycles include communications, reconnaissance, troop movement, supply of provisions, and patrol. See also: bicycle infantry.
A response to an inquiry made to the Mass DOT/RMV indicates that Massachusetts does recognize the federal low speed electric bicycle Federal Law (15 U.S.C. § 2085) and interprets that to mean these ebikes do not require license or registration. However, some of the materials available on the RMV website do not distinguish between "Motorized Bicycle" and low power ebikes. One form, Bicycle Conversion to Motorized Bike, does document the exemption of low power ebikes.[100]
We need to support and put our purchasing power behind ebikes sold in the U.S. that are trying to comply with the California rules which allow 500w and 750w nominal motors and establish 3 classes. If these bikes can create a big enough footprint in the market then future U.S. bike rules may universally adopt these standards. It is better than engaging in regulation showdowns without any standardized and unified proposal on the part of the Electric Bike Community.

Seth Miller said he founded the company after his first electric bike was stolen from where it was parked in front of the midtown office building where he worked. The company that manufactured the bike had disbanded, so he started researching different suppliers. He soon discovered that a majority of the e-bikes sold in the US are just cobbled together from a variety of off-the-shelf Chinese-made parts found in a catalog. It sounded simple, so Miller figured he’d try it himself.

Toe-clips and toestraps and clipless pedals help keep the foot locked in the proper pedal position and enable cyclists to pull and push the pedals. Technical accessories include cyclocomputers for measuring speed, distance, heart rate, GPS data etc. Other accessories include lights, reflectors, mirrors, racks, trailers, bags, water bottles and cages, and bell.[52] Bicycle lights, reflectors, and helmets are required by law in some geographic regions depending on the legal code. It is more common to see bicycles with bottle generators, dynamos, lights, fenders, racks and bells in Europe. Bicyclists also have specialized form fitting and high visibility clothing.


Connect the battery to the speed controller and the throttle. Follow the instructions included with the kit to connect each part. Typically, you’ll only need to plug the connector on the speed controller into the connector on the battery, then repeat the process for the throttle. Be sure not to touch the battery wires together, as this could create a dangerous spark! [14]
We spent 46 hours on research, videography, and editing, to review the top choices for this wiki. Despite their growing popularity among commuters and recreational cyclists, most e-bikes aren't designed to fit easily into the trunk of a car or on crowded public transit systems. So for more portable pedaling power on the way to and from work, or wherever you roam, just pick up one of these handy folding electric models. They are as useful as their non-folding brethren, only more convenient. When users buy our independently chosen editorial picks, we may earn commissions to support our work. Skip to the best folding electric bike on Amazon.
During nighttime operation, the bicycle must be equipped with a front headlamp, a rear-facing red reflector, and reflectors on the front and rear of pedals, and the bicycle or rider must have reflective surfaces on each side. Minn. Stat. §169.222, subd. 6. An electric-assisted bicycle can be equipped with a front-facing headlamp that emits a flashing white light, a rear-facing lamp that has a flashing red light, or both. The bicycle can carry studded tires designed for traction (such as in snowy or icy conditions).

Bicycles are popular targets for theft, due to their value and ease of resale.[113] The number of bicycles stolen annually is difficult to quantify as a large number of crimes are not reported.[114] Around 50% of the participants in the Montreal International Journal of Sustainable Transportation survey were subjected to a bicycle theft in their lifetime as active cyclists.[115] Most bicycles have serial numbers that can be recorded to verify identity in case of theft.[116]

We've also released our first native 72V battery pack in a conventional downtube battery casing, assembled using the high power Samsung 27100 40T cells so that even with the small 8Ah capacity it is able to deliver 40-50A continuous currents. This is an ideal battery for fast and sporty offroad ebike builds, allowing powerful performance without the weight or complexity of most 72V setups (either two 36V packs in series or a large triangle frame battery).
Bicycles can be categorized in many different ways: by function, by number of riders, by general construction, by gearing or by means of propulsion. The more common types include utility bicycles, mountain bicycles, racing bicycles, touring bicycles, hybrid bicycles, cruiser bicycles, and BMX bikes. Less common are tandems, low riders, tall bikes, fixed gear, folding models, amphibious bicycles, cargo bikes, recumbents and electric bicycles.

One of the items we demonstrated at the show is the new GMAC motor series. This is a powerful clutchless geared hub motor developed over the past 2 years in partnership with MAC motors, using a custom axle with an integrated splined torque arm. Imagine a MAC motor with perfect frame fit for modern bicycles, zero torque transmission on the dropouts, and phenomenal regenerative braking control.

At the end of the day, it’s probably best to spend as much as you can to get the bike with the most range that folds up the smallest. Once these puppies run out of juice, they tend to be much harder to pedal than their non-electric counterparts, mainly due to their increased weight, so keep an eye out for lighter models if you know you’re the type to overextend a biking trip. Other features to look out for include racks to help you carry important materials, charging time, and, of course, safety implements like lights and reflectors.
Power-assist: Also known as pedal-assist bikes, these are the bicycle equivalents of hybrid cars: they're designed to be pedaled quite a lot of the time and electrically powered either when you're tired or when you feel like a bit of electric help (when you're going up hill, for example). Unlike full-power bikes, they don't have hub motors; instead, there's a separate electric motor mounted near the rear wheel and driving it either through the gear sprocket or simply by pressing against the rear tire. Where a hub motor is difficult or impossible to pedal without any power (because you're effectively turning it into a generator), power-assist motors turn easily with little or no resistance when you pedal. That gives power-assist bikes much greater range than hub-motor ones (as much as 80–145km or 50–90 miles).
Photo: Left: The hub motor of an electric bike. Right: If you took off the casing, this is the kind of thing you'd see. It's a simple brushless motor from a PC cooling fan, but it works in broadly the same way as a bike's hub motor. There's a static part made up of four electromagnet coils (left) and a rotating part (right) made from a permanent magnet (the gray ring) that clips onto it. When the coils are energized in sequence, they generate a magnetic field that makes the permanent magnet and fan spin around. At a glance, a hub motor looks much like an ordinary bicycle hub, but look closer and you'll find it's a lot more bulky.
Operators are subject to driving rules and equipment requirements (if applicable) when operated on the public streets or highways (which includes the main traveled portion of the road, shoulder and sidewalk). This means that an operator could be cited for speeding, failure to signal, unsafe change of course, driving on the sidewalk, DWI (this would apply to anywhere in the state and not just the streets/highways), and all other driving rules contained within state law that would apply. They may also not ride more than two abreast and may not impede the normal and reasonable movement of traffic. On a laned roadway, they must operate within a single lane.[citation needed]
"Bicycle" means either of the following: (1) A device having two wheels and having at least one saddle or seat for the use of a rider which is propelled by human power. (2) A device having two or three wheels with fully operable pedals and an electric motor of less than 750 watts (one horsepower), whose maximum speed on a paved level surface, when powered solely by such a motor while ridden, is less than 20 miles per hour.
Electric bicycles have two main methods of operation: pedal-assist and/or throttle-control. As the name implies, pedal-assist “assists” your pedaling and requires some input. With this method, a torque sensor picks up movement or stress to determine the power requirements of the rider. Everything is automated so there’s nothing to think about, just jump on and start riding. Some bikes have multiple settings, while others have just one setting with the addition of a throttle control. Depending on the setting, pedal-assistance can help a little – or a lot. At lower settings, pedal-assist is barely noticeable but helps extend your range. At higher settings, the power is quite obvious and feels like a strong wind at your back with the motor doing most of the work while you pedal along.
This is an unofficial guide to the laws governing electric bicycles in the United States as of 2016. It was contributed by a guest writer The Smart Ped`aleck who was paid and remains unaffiliated with any electric bicycle company. It may be updated ongoing and is cited throughout with reference links and attributions at the end. It is designed to be an entertaining starting point for understanding the space, digging deeper and in turn choosing the best electric bike platform for your needs.
Several bills have been sponsored to legalize electric bicycles for use on NYS roads, and several have overwhelmingly passed at the committee level, but none of these initiatives has been able to be heard and then passed in the New York State Senate, until 2015. The latest bill S3997, "An act to amend the vehicle and traffic law, in relation to the definition of electric assisted bicycle. Clarifying the vehicle and traffic law to define electric assisted bicycles; establish that electric assisted bicycles, as defined, are bicycles, not motor vehicles; and establish safety and operational criteria for their use." has passed in the Senate for the first time ever in 2015.[116] The related Assembly bill A233 was not brought to a vote in the assembly even though it had passed with little issue in prior years.[117]
Übrige "Motorfahrräder": “E-Bikes mit einer Leistung zwischen 500 und 1000 Watt oder einer bauartbedingten Höchstgeschwindigkeit von 20 bis 30 km/h oder einer Tretunterstützung, die auch bei einem Tempo von 25 – 45 km/h wirkt, gelten als Motorfahrräder und benötigen ein entsprechendes Kontrollschild.”. You can use any bicyle path and also hiking roads forbidden to motorbikes if you drive slowly.

However, Emu sells a little foldable number if that's your bag. The Emu Crossbar is for  town commuters that require a sweet ride that's backed up by solid Shimano Nexus hub gears and Tektro brakes, which are adequate if not the best on the market. Riding is smooth and easy, with the crank moving sensor doing its best to iron out any gaps in power delivery.
With a chain drive transmission, a chainring attached to a crank drives the chain, which in turn rotates the rear wheel via the rear sprocket(s) (cassette or freewheel). There are four gearing options: two-speed hub gear integrated with chain ring, up to 3 chain rings, up to 11 sprockets, hub gear built into rear wheel (3-speed to 14-speed). The most common options are either a rear hub or multiple chain rings combined with multiple sprockets (other combinations of options are possible but less common).
With hand-operated brakes, force is applied to brake levers mounted on the handlebars and transmitted via Bowden cables or hydraulic lines to the friction pads, which apply pressure to the braking surface, causing friction which slows the bicycle down. A rear hub brake may be either hand-operated or pedal-actuated, as in the back pedal coaster brakes which were popular in North America until the 1960s.

I am very pleased with the quality and performance of this electric bike. I find that the twist grip throtle works better for me than the peddle assist low, medium and high settings. It is not necessary to change out of high gear to climb most hills while peddling with the throttle also providing power. The shocks work well on dirt paths and the seat is comfortable. This bike goes maximum speed up to 19 mph on flat ground. I have

Ebike definition in Colorado follows the HR 727 National Law: Template:Convert e-power and Template:Convert max, 2 or 3 wheels, pedals that work. Legal low powered Ebikes are allowed on roads and bike lanes unless the city or county has passed laws to the contrary (Boulder city bans ebikes over 400W from bike lanes and all ebikes from bike paths) -none -(except Boulder city) have to date. Bicycles and Ebikes are disallowed on certain high speed highways and all Interstates unless signed as "Allowed" in certain rural Interstate stretches where the Interstate is the ONLY means of travel. [35] Unless the locality has specifically passed laws making ebikes illegal on sidewalks or trails, Ebikes are legal. However most business and shopping districts do not allow riding bikes or ebikes on sidewalks. Boulder and a few other cities specifically dis-allow ebikes on their trail systems through legal statute.


October 5, 2009 — Ontario is bringing in some new safety requirements for electric bikes. E-bikes, which can reach a speed of 32 kilometres per hour, are allowed to share the road with cars, pedestrians and other traffic throughout the province. The new rules limit the maximum weight of an e-bike to 120 kilograms, require a maximum braking distance of nine metres and prohibit any modifications to the bike's motor that would create speeds greater than 32 kilometres per hour. Also, riders must be at least 16 years of age, wear approved bicycle or motorcycle helmets and follow the same traffic laws as bicyclists. Municipalities will be able to decide where e-bikes may be used on their streets, bike lanes and trails. E-bikes will not be permitted on 400-series highways, expressways or other areas where bicycles are not allowed. Riding an e-bike under the age of 16 or riding an e-bike without an approved helmet carries fines ranging from $60 to $500. For all other traffic offences, e-bike riders will be subject to the same penalties as cyclists.

Indian law requires that all electric vehicles have ARAI[50] approval. Vehicles with below 250W and speed less than 30 km/h, do not require certification- hence not following full testing process, but needs to get exemption report from ARAI. Whereas more powerful vehicles need to go through a full testing process following CMVR rules. This can take time and cost money but assures safe and reliable design for Electric Vehicles. These regulations are not promulgated by the Regional Transport offices, and riders are not required to obtain a licence to drive, to carry insurance, or to wear a helmet.
While I would have loved to see some higher end components such as disc brakes or built-in lights, the bike still works well for what you get and is a pretty good value for the price. One missing component that I feel would make a big difference is a kickstand. I’ve never seen an e-bike that didn’t come with one, outside of ultra premium multi-thousand dollar road and downhill e-bikes that try to save every gram of weight. But for a commuter, a kickstand is pretty important. You can always add a cheap $7 kickstand from Amazon, but I would have preferred they save us the step and include their own cheap kickstand.
This article did a good job of trying to justify the assist speed limits but fell short of detailing how that can ever be effectively enforced. In reality the only enforcement that is going to work is applied speed limits to use of bikes and ebikes. For example, it makes sense that a bike lane on a street that the speed limit of vehicles is the speed limit of the bikes/ebikes. On sidewalks and shared pedestrian paths the speed limit probably does need to be in the 15-20mph range to match traditional bikes speeds on those paths.
Conversion kits, on the other hand, are sold and installed separately on traditional bicycles. They are harder to setup and conceal, and require some basic mechanical ability and a little bit of ‘elbow grease’ to install. The advantage of conversion kits is that you can choose almost any standard bicycle, and you have the freedom to change or upgrade components as you go. A conversion kit will also allow you to achieve higher power and speed ratings that are not possible on most pre-built electric bike models. Kits are great for tall or heavy riders because they can opt for a larger bike, with higher power and weight carrying capacity. People living in hilly terrain may require the additional torque to handle extremely large inclines. For people who prefer a specific bike model or just love to go faster, a conversion kit offers enormous flexibility.
×