Geared Hub Motors – Most pre-built e-bikes use brushless geared hub motors. These motors have internal planetary gears that help transfer power from the motor to the wheel. Because of the internal gearing, these motors provide excellent torque but are limited in top speed. On the plus side, the improved torque means better take-off power and hill climbing ability. Plus, less wattage is required to get the motor turning and they’re typically small and lightweight. On pre-built e-bikes, these motors range from 200w-500w and go up to 20mph. But some aftermarket kits can be as powerful as 1000w, with increased top speeds and huge amounts of torque (ideal for extremely hilly terrain). Besides lower top speeds, these motors tend to be expensive and it’s possible the gears will eventually wear out and need to be replaced (this is highly unlikely, they las quite a long time). Good examples are Ancheer bikes.
Nevada Electric Bicycle (NRS 482.0287) Bicycle 20 (motor only on the flat with 170LB rider, undefined if pedal assist is allowed to go faster) 750W (it is undefined as to whether this is input or output power, but in the USA, motors are rated on output power at the shaft) No none (use caution here because of "reckless endangerment" laws) no (not a "motor vehicle")

E-bikes are typically offered in 24V, 36V and 48V configurations. Higher voltage generally means higher top speed – but that may not always be the case. Since the efficiency of a motor and drive system can have an effect on power and speed, a 24V setup could have the same top speed as a 36V setup. Generally you can expect 15-18 mph on a 24v setup, 16-20 mph on a 36V setup and 24-28 mph on a 48V setup. Although it far exceeds Federal laws, some conversion kits can even be run at 72V for speeds of 35+ mph! However, this puts significant stress on bicycle components. Consider that even the fastest athletes only travel 17-18 mph on a conventional bicycle, so 20 mph feels very fast to most riders. Anything over this speed can be unsafe and exceeds law regulations.
Choose a 36- or 48-volt battery with a capacity of 10Ah or 20Ah. Choose a battery designed for use on an electric bicycle, as it will come with a charger and be much easier to install. Make sure the voltage and capacity of the battery you choose is compatible with the conversion kit you purchased. The higher the voltage of your bike's battery, the more powerful your bike will be. When building an electric bike, choose a 36- or 48-volt battery to allow for speed and comfort.[5]
According to Utah Code 41-6a-102 (17) an electric assisted bicycle is equipped with an electric motor with a power output of not more than 750 watts and is not capable of further assistance at a speed of more than 20 MPH, or at 28 MPH while pedaling and using a speedometer. New laws specifically exclude electric pedal-assisted bicycles as "motorized vehicles" and bicycles are permitted on all state land (but not necessarily on Indian Reservations, nor restrictive municipalities, such as in Park City Code 10-1-4.5 2) if the motor is not more than 750 Watts, and the assistance shuts off at 20 mph (Utah Traffic Code 53-3-202-17-a 1). E-bikes sold in Utah are required to have a sticker that details the performance capacity. Children under 14 can operate an electric bicycle if accompanied by a parent/guardian, but children under 8 may not. (Utah code 41-6a-1115.5) No license, registration, or insurance is required by the State but some municipalities may require these measures (Salt Lake City and Provo require registration).
With hand-operated brakes, force is applied to brake levers mounted on the handlebars and transmitted via Bowden cables or hydraulic lines to the friction pads, which apply pressure to the braking surface, causing friction which slows the bicycle down. A rear hub brake may be either hand-operated or pedal-actuated, as in the back pedal coaster brakes which were popular in North America until the 1960s.
2. Agreement to Rules: By participating, you agree to be fully unconditionally bound by these Rules, and you represent and warrant that you meet the eligibility requirements set forth herein. In addition, you agree to accept the decisions of Electric Bike Technologies INC., as final and binding as it relates to the content. The Sweepstakes is subject to all applicable federal, state and local laws.
From all the Chinese brands that have come and disappeared, Onway is still standing strong. That means that they have sold enough bikes, and they have been tried and tested enough for customers to know what to expect. So, what can you expect from this Onway bike? Well, for a very affordable price, you will get anything you realistically need in an e-bike – multi-purpose tires for various terrains, LCD display, LED headlights, taillights, a kickstand… Overall build quality and quality of the parts is above average, but there are some things that you will need to change, and seat should be the first on the list. Customer support is not that great, but if you decide to purchase this bike you will get a fun bike, for affordable price that you will be able to assemble and ride in no time.
On the road, it takes only a few turns of the pedals to activate the Vado’s motor and get it up to speed. In Turbo mode — the bike’s highest level of pedal-assist — the Vado reaches speeds of up to 28 miles per hour, after which the electric drive system automatically shuts off to conserve power (and abide by local law). A built-in LED readout on the handlebars allows riders to monitor battery life, check current speed, and track calories burned while also being able to glance at distance traveled. The Turbo Vado Mission Control app (iOS/Android) also connects to the bike via Bluetooth and allows riders to further tune their ride and adjust the bike’s settings.
10. Limitation of Liability: By entering you agree to release and hold harmless Electric Bike Technologies INC. and its subsidiaries, affiliates, advertising and promotion agencies, partners, representatives, agents, successors, assigns, employees, officers and directors from any liability, illness, injury, death, loss, litigation, claim or damage that may occur, directly or indirectly, whether caused by negligence or not, from (i) such entrant's participation in the sweepstakes and/or his/her acceptance, possession, use, or misuse of any prize or any portion thereof, (ii) technical failures of any kind, including but not limited to the malfunctioning of any computer, cable, network, hardware or software; (iii) the unavailability or inaccessibility of any transmissions or telephone or Internet service; (iv) unauthorized human intervention in any part of the entry process or the Promotion; (v) electronic or human error which may occur in the administration of the Promotion or the processing of entries.
That being said, It is fun to ride - my 13 year old grandson likes it a lot. I feel it is best used on hard surfaces like sidewalks and hard floors. I received this little scooter 3 days ago and have ridden it in Costco and Sam's club and took it to an art show and sale as well as driving it through hospital halls on the way to and from a meeting.. One has to

Gearless (Direct-Drive) Hub Motors – Some conversion kits (and bikes) use gearless, direct-drive motors. On this type of motor, the axle that passes through the center of the motor is actually the axle of the motor itself, with the copper windings fixed to the axle. The magnets are mounted to the outer shell of the hub motor. When electricity is applied to the stator a magnetic field is induced that causes the magnets to move. This in turn makes the whole shell of the motor turn and propels the e-bike forward. Even though corrosion will eventually have an impact, this type of motor should last for years since there’s no gearing and no contact between moving parts. They’re also capable of higher top speeds. But since there’s no gears, they have less torque and it requires more power to get the motor up to speed. Most direct-drive hub motors are 350w-500w and reach speeds of 18-25 mph. But more powerful motors can reach speeds of 35+ mph.
In cities where bicycles are not integrated into the public transportation system, commuters often use bicycles as elements of a mixed-mode commute, where the bike is used to travel to and from train stations or other forms of rapid transit. Some students who commute several miles drive a car from home to a campus parking lot, then ride a bicycle to class. Folding bicycles are useful in these scenarios, as they are less cumbersome when carried aboard. Los Angeles removed a small amount of seating on some trains to make more room for bicycles and wheel chairs.[65]
As of May 19, 2009, Nevada amended its state transportation laws to explicitly permit electric bicycles to use any "trail or pedestrian walkway" intended for use with bicycles and constructed with federal funding, and otherwise generally permits electric bicycles to be operated in cases where a regular bicycle could be. An electric bicycle is defined as a two- or three-wheeled vehicle with fully operable pedals with an electric motor producing up to 1 gross brake horsepower and up to 750 watts final output, and with a maximum speed of up to 20 miles per hour on flat ground with a 170 pound rider when powered only by that engine. (AB441, amending NRS 480, 482 and other sections)
This thing is also kitted out with a full SRAM groupset, RockShox Yari RC front shocks, Custom Fox Float suspension at the rear and enormously punchy SRAM disc brakes at the front and rear. Fundamentally, it's a mighty off-road machine with pro-spec kit that introduces a new style of trail riding, allowing adrenaline junkies to ride further, climb harder and descend faster than ever before.
On February 4, 2014, SB997 was introduced by Senator Matt Smith, which seeks to amend PA Vehicle Code to include "Pedalcycle with Electric Assist". In a memo addressed to all senate members, Smith said the definition shall include "bicycles equipped with an electric motor not exceeding 750 watts, weighing not more than 100 pounds, are capable of a maximum speed of not more than 20 mph, and have operable pedals."[128][129]

We've also released our first native 72V battery pack in a conventional downtube battery casing, assembled using the high power Samsung 27100 40T cells so that even with the small 8Ah capacity it is able to deliver 40-50A continuous currents. This is an ideal battery for fast and sporty offroad ebike builds, allowing powerful performance without the weight or complexity of most 72V setups (either two 36V packs in series or a large triangle frame battery).

In a parallel hybrid motorized bicycle, such as the aforementioned 1897 invention by Hosea W. Libbey, human and motor inputs are mechanically coupled either in the bottom bracket, the rear wheel, or the front wheel, whereas in a (mechanical) series hybrid cycle, the human and motor inputs are coupled through differential gearing. In an (electronic) series hybrid cycle, human power is converted into electricity and is fed directly into the motor and mostly additional electricity is supplied from a battery.
Hmm, I think it depends on the forest. My experience has been that if you have a Class 1 ebike and are riding respectfully, most places allow it. I have a sensitive knee and carry a doctor’s note citing disability laws in Colorado and have never been approached or asked by a ranger or fellow rider about the legality of my bike. That said, I have been using the really quiet and hidden Brose motor and I ride carefully and am friendly with everyone
The Christmas day is coming soon, since I receive the bike, it's about a week, and I am satisfied with it! just as advertised, very powerful and good design. the most important point is that once the battery is FULL CHARGE, how far it can reach up to. I have a funny test, in the normal road(not in the dramatic slope or uphill), it can goes almost 44 miles. That is what I give 5 star for this bike! very powerful with reasonable price!
A new electric cyclist will likely experience two conflicts of thought: 1). Will the general public accept my use of this power assist technology, or Will they ridicule and reject me as being lazy? 2). Will I stand out to law enforcement by the look of my bike or riding a bit faster than other cyclist on hills and roads? Grappling with these two thoughts will tempt most folks to try and remain unnoticed and ride more responsibly. After I became an advocate of e-transportation on two wheels, enjoying the benefits of power assist commuting, I eventually was a bit put off by this federal law, especially the 20mph limitation. Is 20 mph really practical and justified? Is it not true that many active young people on typical road bicycles are able to actively ride in the 20-25mph range? I discovered that ebikes, with larger tires and disk brakes, can comfortably and safety cruise in that range of speed. The standard 2001 Federal law of 20mph, eventually became a practical limitation for an ebike commuter of over 20 miles a day, and caused me to get a bike beyond the federal limits, making me more alert and sensitive when riding in the presence of the police.
Riding a pedal-assisted road bike may seem counterintuitive but during longer training sessions, the minimal addition of power helps prevent overall muscle fatigue and injury. Similarly, those looking to enjoy longer scenic routes will appreciate the general boost an electric drive provides. With a top speed of 28 mph, the Road E+1 uses three power modes to give you ultimate control over your ride and assistance level. A four-point sensory system monitors the pedaling force allowing the motor to amplify your movements seamlessly.
But two other concerns are also front and center when it comes to biking: cost and convenience. Not many people have showers at their places of employment, and who wants to show up to work coated in sweat and stinky for the rest of the day? Electric bikes solve the convenience problem by making the process almost effortless; you can bike for miles—even up and down hills—without breaking a sweat.

The other shout-out goes to Paul Bogaert who decided to close the Bike Doctor after 27 years and instead cycle tour the world with his wife. Paul had an early role in Vancouver bicycle advocacy and at bringing cycle riding to a less elitist/athletic and more everyday commuter crowd through their shop.  They were among the early shops to embrace family friendly cargo bikes and  appreciated the role that electric would play in making cycling more broadly appealing.
Some electric bikes claim to use a neat trick called regenerative braking. If you start pedaling the bicycle or going downhill, the spinning wheels turn the electric motor in the hub in reverse and start charging up the batteries. In practice, regenerative braking is nowhere near as useful on an electric bicycle as it is on an electric train or car. An electric bike has much less mass and velocity than either a train or car, so it never gains (or loses) anything like as much kinetic energy when it starts and stops. You'd have to go down an awful lot of hills to charge up the batteries completely and that's usually not practical. And what's the point in pedaling the wheels simply to charge the battery? You might as well have bought an ordinary bicycle to start with!
The new Electric Bike Kit Owners group on Facebook has taken off within the first week of its creation. Around 400 people have joined the online group with new members being added every day. E-bike riders are sharing the various ways that they have converted their bikes using the E-BikeKit Complete Electric Bike Conversion System. Each one of the electric bike conversions is more unique than the next. Some e-bike converters have added flashy lights, flags, and other features to make their electric bikes fit their personalities. One electric bike conversion kit was even used to build a three-seat electric...
Use of and/or registration on any portion of this site constitutes acceptance of our User Agreement (updated 5/25/18) and Privacy Policy and Cookie Statement (updated 5/25/18). Your California Privacy Rights. The material on this site may not be reproduced, distributed, transmitted, cached or otherwise used, except with the prior written permission of Condé Nast. Ad Choices.

Arkansas does not define E-bikes. The following definition describes a combustion engine. E-bikes being electric do not have a cylinder capacity and thus this law is not technically applicable. The state defines a "Motorized bicycle" as "a bicycle with an automatic transmission and a motor of less than 50cc."[80] Riders require either a certificate to operate a motorized bicycle, a motorcycle license, a motor-driven cycle license, or a license of class A, B, C or D. Certificates cannot be issued to riders under 10 years of age.[81]


Our hope is that this plug will become to motors in the 500-1500 watt power range what the 9pin Z910 became for the low power geared motors, with all motor manufacturers agreeing to the same pinout standard for easy swapping and interchangeability . We have an L10 version of the Phaserunner motor controller available now and will soon be expanding this to a Grinfineon offering as well.
Regulations[37] appear to deal with Bicycles with helper motors. No person shall ride a bicycle with a helper motor unless that person holds a valid motor vehicle operator's license. No person shall operate a bicycle with a helper motor at a rate of speed exceeding thirty miles per hour; nor shall any bicycle with a helper motor be operated on any sidewalk, limited access highway or turnpike. Driver's licence is required except if a special permit is obtained by havnig a doctor fill out a certificate and shows they are able to drive the bike with and without the motor assisting.
The BC Bike Show is the premier cycling and outdoors event in Western Canada and is happening in just 2 weeks on March 2nd and 3rd. We'll be there of course, and in addition to our exhibitor booth we'll also be hosting Cycle Stage to give more public presentations. On Saturday at 11:45 am we'll talk on how to navigate the various motor and battery options available for ebike retrofits, and on Sunday at 2pm we'll be doing a live demonstration of a regular bicycle being converted over to electric assist.

Arkansas does not define E-bikes. The following definition describes a combustion engine. E-bikes being electric do not have a cylinder capacity and thus this law is not technically applicable. The state defines a "Motorized bicycle" as "a bicycle with an automatic transmission and a motor of less than 50cc."[80] Riders require either a certificate to operate a motorized bicycle, a motorcycle license, a motor-driven cycle license, or a license of class A, B, C or D. Certificates cannot be issued to riders under 10 years of age.[81]


I have been able to find ebikes of all speeds out in the wild and after years of riding and a reflective posture for the law, I see that lawmakers were thinking less about me and my practical wants as the user, and more about the mass motor vehicle driving public, their perceptions and expectations of ‘typical bicycle speeds’ on the roads and paths. So the laws were made to bicycle NORMS, not the potential performance limits for users.
Legislative changes in 2012 significantly altered the classification and regulatory structure for e-bikes. The general effect was to establish electric-assisted bicycles as a subset of bicycles and regulate e-bikes in roughly the same manner as bicycles instead of other motorized devices with two (or three) wheels. Laws 2012, ch. 287, art. 3, §§ 15-17, 21, 23-26, 30, 32-33, and 41. The 2012 Legislature also modified and clarified regulation of e-bikes on bike paths and trails. Laws 2012, ch. 287, art. 4, §§ 1-4, 20.
Electric bicycle fits under the definition of "moped" under Kentucky law. You don't need tag or insurance, but you need a driver's license. "Moped" means either a motorized bicycle whose frame design may include one (1) or more horizontal crossbars supporting a fuel tank so long as it also has pedals, or a motorized bicycle with a step-through type frame which may or may not have pedals rated no more than two (2) brake horsepower, a cylinder capacity not exceeding fifty (50) cubic centimeters, an automatic transmission not requiring clutching or shifting by the operator after the drive system is engaged, and capable of a maximum speed of not more than thirty (30) miles per hour[94][95] Helmets are required.

Riding a pedal-assisted road bike may seem counterintuitive but during longer training sessions, the minimal addition of power helps prevent overall muscle fatigue and injury. Similarly, those looking to enjoy longer scenic routes will appreciate the general boost an electric drive provides. With a top speed of 28 mph, the Road E+1 uses three power modes to give you ultimate control over your ride and assistance level. A four-point sensory system monitors the pedaling force allowing the motor to amplify your movements seamlessly.
This electric bike received a five star. The assembly was pretty simple. I ordered a set of lights and a over rear tire carrier rack from amazon that took longer to install than it took too assemble the bike.This is a solid built by that is attractive and worthy of this price point. The build quality of this bike was very good. So far I've done a few test and it runs perfect. I've put on 50+ miles on this bike and have used it on flat ground, dirt roads, rocky trails and grassy fields. The bike runs quicker than what I expected from a small 250 W hub motor. I really like it in almost every way.
In Australia the e-bike is defined by the Australian Vehicle Standards as a bicycle that has an auxiliary motor with a maximum power output not exceeding 200 W without consideration for speed limits or pedal sensors.[1] Each state is responsible for deciding how to treat such a vehicle and currently all states agree that such a vehicle does not require licensing or registration. Various groups are lobbying for an increase in this low limit to encourage more widespread use of e-bikes to assist in mobility, health benefits and to reduce congestion, pollution and road danger. Some states have their own rules such as no riding under electric power on bike paths and through built up areas so riders should view the state laws regarding their use. There is no licence and no registration required for e-bike usage.
(15.5) "Electric assisted bicycle" means a device with two or three wheels which has a saddle and fully operative pedals for human propulsion and also has an electric motor. For such a device to be considered an electric assisted bicycle, it shall meet the requirements of the Federal Motor Vehicle Safety Standards, as set forth in 49 C.F.R. Section 571, et seq., and shall operate in such a manner that the electric motor disengages or ceases to function when the brakes are applied. The electric motor in an electric assisted bicycle shall:
80% of your personal Carbon Footprint is made up of three main things. How you POWER your House. What you EAT. How you TRANSPORT yourself. There are major changes happening in all three of these areas. In the next 5-10 years, homes will have economical options to incorporate Power Generation, Power Storage and putting Surplus Power back on the Grid. … 

10. Limitation of Liability: By entering you agree to release and hold harmless Electric Bike Technologies INC. and its subsidiaries, affiliates, advertising and promotion agencies, partners, representatives, agents, successors, assigns, employees, officers and directors from any liability, illness, injury, death, loss, litigation, claim or damage that may occur, directly or indirectly, whether caused by negligence or not, from (i) such entrant's participation in the sweepstakes and/or his/her acceptance, possession, use, or misuse of any prize or any portion thereof, (ii) technical failures of any kind, including but not limited to the malfunctioning of any computer, cable, network, hardware or software; (iii) the unavailability or inaccessibility of any transmissions or telephone or Internet service; (iv) unauthorized human intervention in any part of the entry process or the Promotion; (v) electronic or human error which may occur in the administration of the Promotion or the processing of entries.
Most of you are likely here for the electric bits, though. Those consist of a 500Wh user-swappable Bosch Powerpack battery and a 250W Bosch Active Line Plus motor that delivers 37lb-ft (50Nm) of torque and speeds of up to 20mph (32km/h). The battery takes up to 4.5 hours to reach a 100-percent charge and offers a range of up to 134 miles. With the battery and motor, it's markedly heavier than a comparable urban bike, weighing in at 46lb (20.8kg).
My one complaint is the bike’s weight. This sucker is heavy! The aluminum frame looks light, but the the hub motor (4 pounds) and battery (5 pounds) add up. The bike’s total weight is 39 pounds, which is about average for e-bikes but not something you’d want to lug around all day. “This is not a solution for everybody,” Miller admits. “If you live in a fifth floor walkup this is probably not going to work.”

Both land management regulators and mountain bike trail access advocates have argued for bans of electric bicycles on outdoor trails that are accessible to mountain bikes, citing potential safety hazards as well as the potential for electric bikes to damage trails. A study conducted by the International Mountain Bicycling Association, however, found that the physical impacts of low-powered pedal-assist electric mountain bikes may be similar to traditional mountain bikes.[68]

"Medical Exemptions" are also a standard right in the State of Texas for motorcycles & even bicyclists. Through Texas's motorcycle helmet law (bicycle helmet laws from city ordinances), it is only required for those 21 years old or younger to wear a helmet. However, a medical exemption, [59][60][61][62][63][64] written by a certified licensed medical physician or licensed chiropractor, which exempts one from wearing a helmet, can be used for bicyclists if helmets are required.
The environmental credentials of e-bikes, and electric / human powered hybrids generally, have led some municipal authorities to use them, such as Little Rock, Arkansas with their Wavecrest electric power-assisted bicycles or Cloverdale, California police with Zap e-bikes. China’s e-bike manufacturers, such as Xinri, are now partnering with universities in a bid to improve their technology in line with international environmental standards, backed by the Chinese government who is keen to improve the export potential of the Chinese manufactured e-bikes.[67]
In Manitoba Electric Bikes can be classified as a scooter or a moped/mobility vehicle depending on the power of the engine used and its top speed. If the engine on the Electric Bike is less than 50cc and it cannot exceed 50 km per hour the rider is not required to have a motorcycle licence or any specific training.[26] Electric Bikes can be driven by anyone with a Class 5 driver's licence in any stage of the graduated licensing process.[27] A Class 5 Learners Licence requires one to be age 16 (parents consent if under 18) and a visit to a licensing office to pass a vision test and a written knowledge test about the rules of the road and traffic signs.[28]
×