The time or distance an electric bike battery will run between chargings is impossible to judge with much accuracy. There are too many variables: terrain, speed, rider weight, bike load (shopping, kids, luggage), and more. However, we can make a few generalizations about an e-bike’s recharge time and overall working life. These generalizations should be used for comparison purposes only.
As of May 19, 2009, Nevada amended its state transportation laws to explicitly permit electric bicycles to use any "trail or pedestrian walkway" intended for use with bicycles and constructed with federal funding, and otherwise generally permits electric bicycles to be operated in cases where a regular bicycle could be. An electric bicycle is defined as a two- or three-wheeled vehicle with fully operable pedals with an electric motor producing up to 1 gross brake horsepower and up to 750 watts final output, and with a maximum speed of up to 20 miles per hour on flat ground with a 170-pound rider when powered only by that engine.
The cargo bike is run by Escargo, and their delivery rider Elric Prynn cycles the delivery bike (he calls her Matilda) from the Quay up the cycle paths to the city centre, avoiding road traffic delays on the Exeter Bridges. The cargo bike is used to deliver hundreds of loaves of bread each day. Escargo was set up in September 2017 by ex-management consultant Jenny Ryding, and the delivery bike was specially made for Jenny by Iceni Cycles in Somerset.
The Class 3 Aventon Pace 500 urban e-bike has five levels of pedal assist and tops out at 28 mph. But the Pace has something not found on a lot of modern e-bikes. In addition to pedal power, it also has a throttle—in the case of the Pace, a small thumb paddle on the left side of the handlebar next to the control unit that holds at a steady 20 mph, no pedaling required. The bike itself has an aluminum frame, a swept-back handlebar, ergo grips, a sturdy kickstand, hydraulic disc brakes, 8-speed Shimano Altus shifting and gearing, 27.5x2.2-inch Kenda e-bike-rated tires, a saddle the size of Texas, and good ol’ classic city/commuter-bike geometry. It doesn’t come equipped with fenders or a rear rack, but you can add them. Power comes in the form of a 500-watt rear-hub motor, a semi-integrated battery on the down tube (with a range of up to 50 miles), and a backlit display unit mounted on the stem.
The two most common types of hub motors used in electric bicycles are brushed and brushless. Many configurations are available, varying in cost and complexity; direct-drive and geared motor units are both used. An electric power-assist system may be added to almost any pedal cycle using chain drive, belt drive, hub motors or friction drive. BLDC hub motors are a common modern design. The motor is built into the wheel hub itself, and the stator fixed solidly to the axle, and the magnets attached to and rotating with the wheel. The bicycle wheel hub is the motor. The power levels of motors used are influenced by available legal categories and are often, but not always limited to under 750 watts.
Several bills have been sponsored to legalize electric bicycles for use on NYS roads, and several have overwhelmingly passed at the committee level, but none of these initiatives has been able to be heard and then passed in the New York State Senate, until 2015. The latest bill S3997, "An act to amend the vehicle and traffic law, in relation to the definition of electric assisted bicycle. Clarifying the vehicle and traffic law to define electric assisted bicycles; establish that electric assisted bicycles, as defined, are bicycles, not motor vehicles; and establish safety and operational criteria for their use." has passed in the Senate for the first time ever in 2015. The related Assembly bill A233 was not brought to a vote in the assembly even though it had passed with little issue in prior years.
It is important to note that if a vehicle has an electric motor greater than 500 watts and is capable of powering the vehicle when traveling at a speed greater than 32 km/h and it does not have a CMVSS compliance label it cannot be registered unless the owner can prove, by having the vehicle certified by an engineer, that it is safe for operation on NB highways. Also, not all vehicles are suitable for operation on NB highways and it could be that the vehicle in question may not be a motor driven cycle or a bicycle and cannot be operated on the highway at all.