7. Winner selection and notification: Winners of the Sweepstakes will be selected in a random drawing under the supervision of the Sponsor. Winners will be notified via e-mail to the e-mail address they entered the Sweepstakes with within five (5) days following the winner selection. Electric Bike Technologies INC. shall have no liability for a winner's failure to receive notices due to winners' spam, junk e-mail or other security settings or for winners' provision of incorrect or otherwise non-functioning contact information. If the selected winner cannot be contacted, is ineligible, fails to claim the prize within 15 days from the time award notification was sent, or fails to timely return a completed and executed declaration and releases as required, prize may be forfeited and an alternate winner selected. The receipt by winner of the prize offered in this Sweepstakes is conditioned upon compliance with any and all federal and state laws and regulations. ANY VIOLATION OF THESE OFFICIAL RULES BY ANY WINNER (AT SPONSOR'S SOLE DISCRETION) WILL RESULT IN SUCH WINNER'S DISQUALIFICATION AS WINNER OF THE SWEEPSTAKES AND ALL PRIVILEGES AS WINNER WILL BE IMMEDIATELY TERMINATED.
Great question… a real world situation from someone doing their best to follow the law but also be realistic about time/distance. What follows is my opinion on the matter based on lots of electric bike riding experience, this is not legal advice. You can probably ride with electric assist across the dirt way with no issues and avoid any negative response that might arise as long as you’re polite to other cyclists and pedestrians and pedal along without going too fast. If someone called you out about it you could easily hop off, walk your bike and explain that you use the assist to help make your commute possible or possibly, like me, you have a knee injury and it’s difficult to pedal through softer terrain like gravel. Another different approach might be to shut the bike off completely before entering the gravel section, you could even take the battery off and put it in a backpack or as mentioned earlier… just walk the bike. Imagine if you had a motorized dirt bike and were just pushing it along a sidewalk… this kind of vehicle definitely is not allowed on sidewalks or most gravel paths like the one you’re describing but if you were escorting it carefully, you’d be honoring the spirit of the law and if an officer or pedestrian jumped out and started questioning you about your “motorized vehicle” it is my feeling that a genuine explanation and apology or request for guidance would go very well. I personally have never had issues riding electric bikes in part because I am thoughtful about how I use them. I do occasionally switch them off and sometimes I get off and walk. I have asked police in many cities across the US what they thought about ebikes and in every case I have received positive interest and support with guidance to ride safe with a helmet and follow traffic laws in the street. I hope this helps and I wish you well, it’s nice that you care enough to ask and I hope you’re treated well by others out on the road. The flip side of this response is that I have been harassed, yelled at and even swerved at by automobiles when riding bicycles and electric bikes. This usually happens in the evening after work lets out when traffic is heavy and I’m riding on the shoulder or in the street (where marked to do so) and I believe it has to do with territory, testosterone and socio-economic standing more so than laws or anything like that.
In a parallel hybrid motorized bicycle, such as the aforementioned 1897 invention by Hosea W. Libbey, human and motor inputs are mechanically coupled either in the bottom bracket, the rear wheel, or the front wheel, whereas in a (mechanical) series hybrid cycle, the human and motor inputs are coupled through differential gearing. In an (electronic) series hybrid cycle, human power is converted into electricity and is fed directly into the motor and mostly additional electricity is supplied from a battery.
The bicycle's invention has had an enormous effect on society, both in terms of culture and of advancing modern industrial methods. Several components that eventually played a key role in the development of the automobile were initially invented for use in the bicycle, including ball bearings, pneumatic tires, chain-driven sprockets and tension-spoked wheels.
Some of the Rad Wagon’s (small) flaws became apparent once I added more weight to the bike. The integrated rear rack can attach various panniers, platforms, or baskets to cary your cargo, but I was most concerned with hauling my two kiddos to school. Riding the bike with my three year old was a cinch; he held on to the bars in the caboose (available as an accessory add-on) and enjoyed the view. Adding my very tall, almost seven-year-old daughter, however, was a bit more complicated.
By 1898 a rear-wheel drive electric bicycle, which used a driving belt along the outside edge of the wheel, was patented by Mathew J. Steffens. Also, the 1899 U.S. Patent 627,066 by John Schnepf depicted a rear-wheel friction “roller-wheel” style drive electric bicycle. Schnepf's invention was later re-examined and expanded in 1969 by G.A. Wood Jr. with his U.S. Patent 3,431,994. Wood’s device used 4 fractional horsepower motors; connected through a series of gears.
Again, these are base level components here. The Shimano/TX55 gearing is fine for this application level but I have lost my chain a few times in a few weeks. The frame is surprisingly solid aluminum alloy which feels stiffer and lighter than last year’s Ancheer. The supplied front 10W light is very bright, however the back light is charged via USB and has a push button rather than being wired into the controller. The disc brakes are the same no-name brand as the Ancheer but appear to be a size bigger. The fork, while not amazing, is a big improvement in stiffness and give over the Ancheer’s, which scared me a bit.
On October 5, 2009, the Government of Ontario brought in laws regulating electric bikes in the province. E-bikes, which can reach a speed of 32 kilometres per hour, are allowed to share the road with cars, pedestrians and other traffic throughout the province. The new rules limit the maximum weight of an e-bike to 120 kilograms, require a maximum braking distance of nine metres and prohibit any modifications to the bike's motor that would create speeds greater than 32 kilometres per hour. Also, riders must be at least 16 years of age, wear approved bicycle or motorcycle helmets and follow the same traffic laws as bicyclists. Municipalities are also specifically permitted by the legislation to restrict where e-bikes may be used on their streets, bike lanes and trails, as well as restricting certain types of e-bike (e.g. banning "scooter-style" e-bikes from bicycle trails). E-bikes are not permitted on 400-series highways, expressways or other areas where bicycles are not allowed. Riding an e-bike under the age of 16 or riding an e-bike without an approved helmet are new offences in the legislation, carrying fines of between $60 and $500. E-bike riders are subject to the same penalties as other cyclists for all other traffic offences.
The federal law will not prohibit a motor vehicle label and additional restrictions given by the state. States will typically define e-mopeds in the 1000W range (1.5 hp) and speeds attainable to 30mph, and include a few requirements such as a helmet, eye protection, and a driver’s license. States may also require title, registration, and insurance for mopeds.
Controllers for brushless motors: E-bikes require high initial torque and therefore models that use brushless motors typically have Hall sensor commutation for speed and angle measurement. An electronic controller provides assistance as a function of the sensor inputs, the vehicle speed and the required force. The controllers generally allow input by means of potentiometer or Hall Effect twist grip (or thumb-operated lever throttle), closed-loop speed control for precise speed regulation, protection logic for over-voltage, over-current and thermal protection. Bikes with a pedal assist function typically have a disc on the crank shaft featuring a ring of magnets coupled with a Hall sensor giving rise to a series of pulses, the frequency of which is proportional to pedaling speed. The controller uses pulse width modulation to regulate the power to the motor. Sometimes support is provided for regenerative braking but infrequent braking and the low mass of bicycles limits recovered energy. An implementation is described in an application note for a 200 W, 24 V Brushless DC (BLDC) motor.
In Manitoba Electric Bikes can be classified as a scooter or a moped/mobility vehicle depending on the power of the engine used and its top speed. If the engine on the Electric Bike is less than 50cc and it cannot exceed 50 km per hour the rider is not required to have a motorcycle licence or any specific training. Electric Bikes can be driven by anyone with a Class 5 driver's licence in any stage of the graduated licensing process. A Class 5 Learners Licence requires one to be age 16 (parents consent if under 18) and a visit to a licensing office to pass a vision test and a written knowledge test about the rules of the road and traffic signs.
Mid-mounted system means that the electric motor is not built into the wheel but is usually mounted near (often under) the bottom bracket shell. Mid-drive systems tend to feel more like a normal bike, since they drive the pedals, just like your legs, and those who frequently climb long, steep hills tend to prefer mid-drive systems for their ability to handle long climbs. As they can leverage the bicycles lowest gears for climbs, mid drive systems can also leverage the high gears to reach higher speeds on flat areas than a hub system. The mid-drive motor drives the crank, instead of the wheel itself, which multiplies its power and allows it to better take advantage of the bike’s existing gears. If the rider changes the gears appropriately, the motor can turn closer to its ideal rotations per minute which makes a huge difference while climbing hills, so this is a perfect option for those who love mountain biking.
E-bikes can be a useful part of cardiac rehabilitation programmes, since health professionals will often recommend a stationary bike be used in the early stages of these. Exercise-based cardiac rehabilitation programmes can reduce deaths in people with coronary heart disease by around 27%; and a patient may feel safer progressing from stationary bikes to e-bikes. They require less cardiac exertion for those who have experienced heart problems.
The days when eMTBs were defined solely by the power of their motors and the size of their batteries are over. Riding performance has become the most important metric. In that pursuit, manufacturers are increasingly developing eMTBs with less power and battery capacity, which in turn handle more like regular mountain bikes. FOCUS started this movement some time ago with its Project-Y concept and later presented the FOCUS RAVEN² PRO, the first production model in a new category of bikes. However this sporty ride only convinced a handful of riders. Meanwhile, Lapierre and BULLS have both announced full-suspension trail bikes featuring the lightweight FAZUA motor for next year. It remains to be seen how many other brands will jump on board this bandwagon – but the rumour mill has already started rumbling. Moreover, it is only a matter of time before the next motor manufacturer will release its own small, lightweight motor.
The benefits don’t stop at the physical, however. Our daily lives are spent glued to computer and phone screens, and even if you choose to accept that as an inevitable wave of the future, your mind still needs a release from all that toxic screen time. Because a bike moves more slowly than a car, while also giving you much better sight lines and more direct exposure to the sun, a nice ride — even through city streets — will put you more in touch with nature. Getting in touch with your natural environment can drastically reduce stress levels, which is why biking to and from work is such a good idea: no matter how frustrating your day at the office was, you can let it all go on the enjoyable cycling trip home.
All classes of electric-assisted bicycles may be operated on a fully controlled limited access highway. Class 1 and 2 electric bicycles can be used on sidewalks, but Class 3 bicycles "may not be used on a sidewalk unless there is no alternative to travel over a sidewalk as part of a bicycle or pedestrian path." Generally a person may not operate an electric-assisted bicycle on a trail that is designated as non-motorized and that has a natural surface, unless otherwise authorized.
Arkansas does not define E-bikes. The following definition describes a combustion engine. E-bikes being electric do not have a cylinder capacity and thus this law is not technically applicable. The state defines a "Motorized bicycle" as "a bicycle with an automatic transmission and a motor of less than 50cc." Riders require either a certificate to operate a motorized bicycle, a motorcycle license, a motor-driven cycle license, or a license of class A, B, C or D. Certificates cannot be issued to riders under 10 years of age.
Stöckli E.T. Urban Confort, made in Switzerland. It has SwissGoDrive motors and Samsung batteries. There is a 500W/17.6Ah combo that seems to be ideal for commuters, i.e. it has a 50km range using full assistance. In the USA, a similar product is available as Currie eFlow e3 Nitro (different motor and electronics). This model doesn't have a front wheel suspension, but comes with "balloon" tires that somewhat absorb shocks. Options are available through types: "simple"/Urban/CROSS and man/confort models. E.g. the Cross model has a front suspension, a 500W motor and no equipment like lights, fenders, etc. However, paying extra, you can compose your own configuration. If you commute using bumpy roads, then get a front suspension.
Every inch of the bike is thought through, from how the simple, rugged battery connection to the hydraulic disc brakes to the tire choice, to the adorable little bell. The custom battery shape works aesthetically with the frame and is not some obtrusive piece strapped to the down tube of the bike. By putting it down low, it also adds to the stability of the bike, making it handle like a dream, regardless of speed.
Electric bikes are here in a big way. Liberated from some of the normal constraints of standard bike design like weight and gearing, e-bike design has exploded; if you can imagine it, someone has built it. From cargo bikes to city bikes, messenger bikes to mountain bikes, road bikes, folding bikes, and even beach cruisers, there is something for everyone. The beauty of e-bikes is that they make the joy of cycling accessible to so many people in so many ways.
Under Title 23, Chapter 316 of the code, bicycles and motorized bicycles are defined as follows: Bicycle—Every vehicle propelled solely by human power, and every motorized bicycle propelled by a combination of human power and an electric helper motor capable of propelling the vehicle at a speed of not more than 20 miles per hour on level ground upon which any person may ride, having two tandem wheels, and including any device generally recognized as a bicycle though equipped with two front or two rear wheels. The term does not include such a vehicle with a seat height of no more than 25 inches from the ground when the seat is adjusted to its highest position or a scooter or similar device. No person under the age of 16 may operate or ride upon a motorized bicycle. Motorized Scooter—Any vehicle not having a seat or saddle for the use of the rider, designed to travel on not more than three wheels, and not capable of propelling the vehicle at a speed greater than 30 miles per hour on level ground.
Several bills have been sponsored to legalize electric bicycles for use on NYS roads, and several have overwhelmingly passed at the committee level, but none of these initiatives has been able to be heard and then passed in the New York State Senate, until 2015. The latest bill S3997, "An act to amend the vehicle and traffic law, in relation to the definition of electric assisted bicycle. Clarifying the vehicle and traffic law to define electric assisted bicycles; establish that electric assisted bicycles, as defined, are bicycles, not motor vehicles; and establish safety and operational criteria for their use." has passed in the Senate for the first time ever in 2015. The related Assembly bill A233 was not brought to a vote in the assembly even though it had passed with little issue in prior years.
It’s no coincidence that nations with excellent biking infrastructure also have lower rates of obesity and heart disease than nations that do not. The United States, for example, has some small pockets of bike-friendly spaces, usually confined to parts of cities that have been slightly remapped to provide safer, more efficient routes for bicyclists. There’s even been legislation in some cities to regulate how drivers must respect bikers when they encounter them on a shared road.
Further innovations increased comfort and ushered in a second bicycle craze, the 1890s Golden Age of Bicycles. In 1888, Scotsman John Boyd Dunlop introduced the first practical pneumatic tire, which soon became universal. Willie Hume demonstrated the supremacy of Dunlop's tyres in 1889, winning the tyre's first-ever races in Ireland and then England. Soon after, the rear freewheel was developed, enabling the rider to coast. This refinement led to the 1890s invention of coaster brakes. Dérailleur gears and hand-operated Bowden cable-pull brakes were also developed during these years, but were only slowly adopted by casual riders.