I have been able to find ebikes of all speeds out in the wild and after years of riding and a reflective posture for the law, I see that lawmakers were thinking less about me and my practical wants as the user, and more about the mass motor vehicle driving public, their perceptions and expectations of ‘typical bicycle speeds’ on the roads and paths. So the laws were made to bicycle NORMS, not the potential performance limits for users.
(2) BICYCLE.--Every vehicle propelled solely by human power, and every motorized bicycle propelled by a combination of human power and an electric helper motor capable of propelling the vehicle at a speed of not more than 20 miles per hour on level ground upon which any person may ride, having two tandem wheels, and including any device generally recognized as a bicycle though equipped with two front or two rear wheels. The term does not include such a vehicle with a seat height of no more than 25 inches from the ground when the seat is adjusted to its highest position or a scooter or similar device. No person under the age of 16 may operate or ride upon a motorized bicycle.
At just 36V and 5.2 Ah, the battery is not designed for long distance travel. GOTRAX claims the Shift S1 has a range of up to 15 miles (25 km), though that’s only with a lower pedal assist level. If you’re going full throttle, 10 miles (15 km) is a better estimate. But with a battery this small, you could easily charge it at your desk or in the corner of the classroom – lengthening your effective range.
If a car is at fault in an accident with a bicycle or ebike, their motor vehicle insurance will likely cover your cost for repair and hopefully medical expenses. But what happens if you are at fault, riding an ebike illegally because you did not register it as a Moped? At best, you could be prosecuted under the law. At worst, you could be financially liable for neglect or reckless endangerment via a law suit.
In the 1890s, electric bicycles were documented within various U.S. patents. For example, on 31 December 1895, Ogden Bolton Jr. was granted U.S. Patent 552,271 for a battery-powered bicycle with "6-pole brush-and-commutator direct current (DC) hub motor mounted in the rear wheel". There were no gears and the motor could draw up to 100 amperes (A) from a 10-volt battery.[5]
No person may drive either a two-wheeled or a three-wheeled motorcycle, or a motor-driven cycle unless such person has a valid driver's license specially endorsed by the director to enable the holder to drive such vehicles. No driver's license is required for operation of an electric-assisted bicycle if the operator is at least sixteen years of age. Persons under sixteen years of age may not operate an electric-assisted bicycle. Persons operating electric-assisted bicycles shall comply with all laws and regulations related to the use of bicycle helmets. Electric-assisted bicycles and motorized foot scooters may have access to highways of the state to the same extent as bicycles. Electric-assisted bicycles and motorized foot scooters may be operated on a multipurpose trail or bicycle lane, but local jurisdictions may restrict or otherwise limit the access of electric-assisted bicycles and motorized foot scooters, and state agencies may regulate the use of motorized foot scooters on facilities and properties under their jurisdiction and control.

This upgraded model is the best scooter of this type that is currently available on the market. I have permanent mobility issues because of my left leg that do not allow me to walk any long distances. This scooter is allowing me to finally get out of the house to see and do some things again, even if that is just cruising around the neighborhood, but my main reason for purchasing it was so that I can go watch my granddaughters playing softball this spring, they are quite good.


Parliament has decided to approve the speed pedelec – a type of super electric bike that can reach speeds of up to 45 km/hour – for riding on cycle paths. Danish Parliament has decided that as of July 1 2018 those operating the super bikes only need to have turned 15 and wear a helmet, while the licence and number-plate demands will no longer be in play. [38]
In the early 1860s, Frenchmen Pierre Michaux and Pierre Lallement took bicycle design in a new direction by adding a mechanical crank drive with pedals on an enlarged front wheel (the velocipede). This was the first in mass production. Another French inventor named Douglas Grasso had a failed prototype of Pierre Lallement's bicycle several years earlier. Several inventions followed using rear-wheel drive, the best known being the rod-driven velocipede by Scotsman Thomas McCall in 1869. In that same year, bicycle wheels with wire spokes were patented by Eugène Meyer of Paris.[22] The French vélocipède, made of iron and wood, developed into the "penny-farthing" (historically known as an "ordinary bicycle", a retronym, since there was then no other kind).[23] It featured a tubular steel frame on which were mounted wire-spoked wheels with solid rubber tires. These bicycles were difficult to ride due to their high seat and poor weight distribution. In 1868 Rowley Turner, a sales agent of the Coventry Sewing Machine Company (which soon became the Coventry Machinists Company), brought a Michaux cycle to Coventry, England. His uncle, Josiah Turner, and business partner James Starley, used this as a basis for the 'Coventry Model' in what became Britain's first cycle factory.[24]
8. Rights Granted by you: By entering this content you understand that Electric Bike Technologies INC., anyone acting on behalf of Electric Bike Technologies INC., or its respective licensees, successors and assigns will have the right, where permitted by law, without any further notice, review or consent to print, publish, broadcast, distribute, and use, worldwide in any media now known or hereafter in perpetuity and throughout the World, your entry, including, without limitation, the entry and winner's name, portrait, picture, voice, likeness, image or statements about the Sweepstakes, and biographical information as news, publicity or information and for trade, advertising, public relations and promotional purposes without any further compensation.
The environmental credentials of e-bikes, and electric / human powered hybrids generally, have led some municipal authorities to use them, such as Little Rock, Arkansas with their Wavecrest electric power-assisted bicycles or Cloverdale, California police with Zap e-bikes. China’s e-bike manufacturers, such as Xinri, are now partnering with universities in a bid to improve their technology in line with international environmental standards, backed by the Chinese government who is keen to improve the export potential of the Chinese manufactured e-bikes.[67]
No endorsement is required on a driver license in order to operate a motorized bicycle, thus the motorized bicycle may be operated by anyone with a valid driver license. Goggles, windshields and other special equipment required for motorcycles and motor-driver cycles are not required for operation of a motorized bicycle. However, crash helmets are required regardless of operators age. Minors between the ages of 14 and 16 may apply for a restricted license to operate a motorized bicycle, just as they would to operate a motor-driver cycle. For instance, they must take a written test, vision tests and demonstrate their ability to operate the motorized bicycle. The license issued will be restricted to a motorized bicycle only. The license is valid only during daylight hours and within a seven-mile (11 km) radius of the driver's home. Applicants for any type of license less than eighteen (18) years old, must complete a Minor/Teen-age Affidavit and Cancellation form making the parent or legal guardian financially liable for the applicants action. [57]
Introduction A quick of note of my experiences riding a Moustache Dimanche eBike, kindly provided by Fully Charged, on a spectacular 4 day trip, coast-to-coast across Italy. Overall, an amazing experience in terms of the quality of the ride, the scenery and the new experience of quite painless climbing of the many steep hills. I … Continue reading The joys of crossing Italy coast 2 coast on an eBike – by Andreas Credé
Every inch of the bike is thought through, from how the simple, rugged battery connection to the hydraulic disc brakes to the tire choice, to the adorable little bell. The custom battery shape works aesthetically with the frame and is not some obtrusive piece strapped to the down tube of the bike. By putting it down low, it also adds to the stability of the bike, making it handle like a dream, regardless of speed.
First, think about what you need your bike for -- if it's just for a short city commute, in among traffic, then consider a smaller frame that's easy to manoeuvre through cars. The GoCycle G3 (right) is impressively nimble and its electric assistance will help propel you up to 15 mph (24 kph). Better yet, it has built-in lights, automatic gears and you can customise the amount of power the motor provides using a phone app.

When I began testing the Rad Power bike, I wasn’t sure if it would ride like a bakfiets or more like your standard bike. Hundreds of miles later, the RadWagon’s biggest strength is how well it handles. If you aren’t riding with kids, you almost never notice the weight of the cargo area behind you and pedaling is made easy and efficient thanks to a 750W direct drive hub motor and smooth acceleration.

I had gotten this to build an electric bike but I have never worked with wires before so I didn't realize that we needed to attach our own connectors to the wires. The person who I talked to at Joyisi was super nice and explained that to me and even offered to send me connectors for free. I had already ended up getting a different bike altogether though and so I just wanted to return the battery. But because I am returning it for my own reasons (as opposed to the battery being faulty), they would normally have me pay for return shipping and deduct the cost of shipping to me (which is a lot, because they are international) and the inspection fee from my refund, but they were super nice and offered to take on most of the costs and I would only have to pay for the return


As of 2008 a standard class C license, proof of insurance, and registration (annual fee: $9.00) are required for operation of any motorized pedalcycle in Pennsylvania. Additionally, there are strict equipment standards that must be met for operation, including: handlebars, brakes, tires/wheels, electrical systems/lighting, mirrors, speedometer, and horns/warning devices.[127]
After you decide which style of e-bike you want, consider the class. In the U.S., there are three classes defined by the type of assist and how fast the motor will propel you. Most electric bikes sold are class 1 or 3. Class 1 bikes have a motor (max 750w) that assists while you’re pedaling, up to 20 mph. Class 3, also known as “speed pedelec,” can also have up to a 750w motor, but it can assist you up to 28 mph. Both are allowed in most states and cities without requiring a license. Class 2 models have throttles that don’t require the rider to pedal in order to get a boost. They’re allowed on most streets, bike lanes, and paths, but are less popular than the other classes and not covered much here (because not only do we still love to pedal, we also prefer the greater distances that pedal-assist bikes can cover).

Some argue, that an ebike should have some kind of front suspension, i.e. be able to cope with potholes at higher speed or off-road conditions. However, in countries with flat roads (e.g. Switzerland, Germany or Holland) you don't need that extra weight for extra price if you stay on roads and/or drive slowly in difficult terrain. Some makes (like the Stromer) let you choose.
These small complaints prove that the Rad Wagon isn’t perfect. But its overwhelmingly positive qualities clearly outweigh the drawbacks. The Rad Wagon handled beautifully on city streets, accelerating with ease and maintaining a charge for extended range. Rad Power bikes also offers an array of helpful accessories—think racks, baskets, panniers, and platforms—that make the bike nearly as convenient as a car. Time and time again I passed cars stuck in traffic on their daily commute and couldn’t help but wondering: Why don’t more people switch from cars to an e-bike?
Bicycle suspensions are used primarily on mountain bicycles, but are also common on hybrid bicycles, as they can help deal with problematic vibration from poor surfaces. Suspension is especially important on recumbent bicycles, since while an upright bicycle rider can stand on the pedals to achieve some of the benefits of suspension, a recumbent rider cannot.
There is a lot of information on the internet about electric bikes. Hopefully you have found lots of useful information right here, on this website. Based on this information, you may already have a preference for a specific electric bicycle and / or (technical) components. Your friends that ride e-bikes can also advise you based on their own experiences. But there is only one way you will know if you really make the right choice: take a test drive. During a test drive you will discover how close the riding experience is to your expectations.
Under Title 23, Chapter 316 of the code, bicycles and motorized bicycles are defined as follows: Bicycle—Every vehicle propelled solely by human power, and every motorized bicycle propelled by a combination of human power and an electric helper motor capable of propelling the vehicle at a speed of not more than 20 miles per hour on level ground upon which any person may ride, having two tandem wheels, and including any device generally recognized as a bicycle though equipped with two front or two rear wheels. The term does not include such a vehicle with a seat height of no more than 25 inches from the ground when the seat is adjusted to its highest position or a scooter or similar device. No person under the age of 16 may operate or ride upon a motorized bicycle. Motorized Scooter—Any vehicle not having a seat or saddle for the use of the rider, designed to travel on not more than three wheels, and not capable of propelling the vehicle at a speed greater than 30 miles per hour on level ground.[90]
There are two main categories when choosing an e-bike: a pre-built electric bike or a custom e-bike conversion. Prefab electric bikes come in a wide variety of setups and styles and are designed specifically as electric bicycles. With unique characteristics and design qualities, most meet the law requirements which limit power and speed. There is also a variety of options to choose from equipped with different design and different motor and battery configurations to suit different riding styles and preferences: cruisers, commuters, mountain bikes and more. Pre-built e-bikes are clean and sleek in design with all of the wiring and electrical components built directly into the bike. For most people, production e-bikes work great and there’s no need for a custom conversion.
In addition to this, however, you’re going to want to invest in additional safety gear if you don’t want to end up as a statistic. This must include a helmet, as your skull is incredibly vulnerable when moving along at biking speeds. There are even some helmets that have lights and turn signals integrated into their design, giving you greater visibility for drivers.
Bicycles offer an important mode of transport in many developing countries. Until recently, bicycles have been a staple of everyday life throughout Asian countries. They are the most frequently used method of transport for commuting to work, school, shopping, and life in general. In Europe, bicycles are commonly used.[67] They also offer a degree of exercise to keep individuals healthy.[68]
On the topic of visibility, there are a lot of things you can do to make yourself easier to see. You can throw on a reflective vest, for example, which has the added benefit of protecting your work clothes from flying dirt and debris. You can also add lights and reflectors to the bike itself, or strap illuminated bands to your arms and ankles. Both Gestalt theory and several biking visibility studies suggest that moving light sources like the reflectors on pedals that go up and down, are more visible to drivers because our visual systems are designed to pick up on movement (that of prey and predators evolutionarily), making reflective biking shoes a great idea.
This is the bold claim of Oxford-based Zap&Go, a battery technology startup developing Nano-Carbon-ion batteries for electric vehicles.  In a partnership with Chinese battery manufacturer Li-Fun technology, one of the major Lithium-ion battery producers for the electric bike industry, they will launch an electric scooter which will charge in just 5 minutes.  This exciting new technology could help to further develop the electric bike industry, reducing weight and extending battery range.
Ontario is one of the last provinces in Canada to move toward legalizing power-assisted bicycles (PABs) for use on roads, even though they have been federally defined and legal in Canada since early 2001. In November 2005, "Bill 169" received royal assent allowing the Ministry of Transportation of Ontario (MTO) to place any vehicle on road. On October 4, 2006, the Minister of Transportation for Ontario Donna Cansfield announced the Pilot Project allowing PABs which meet the federal standards definition for operation on road. PAB riders must follow the rules and regulations of a regular bicycles, wear an approved bicycle helmet and be at least 16 years or older. There are still a number of legal considerations for operating any bicycle in Ontario.[23][24][25]
Despite the illegal status in the state of New York, enforcement of this law varies at the local level. New York City enforces the bike ban with fines and vehicle confiscation for throttle activated electric bikes.[113] However, Mayor Bill de Blasio has recently changed the city's official policy to legalize pedal-assist electric bikes that have a maximum speed limited to 20 mph. [114] Contrarily, Tompkins County supports electric bike usage, even providing grant money to fund electric bike share/rental projects.[115]
Rad Power’s lineup of 2019 bikes start at $1,699 (there’s also a Cyber Monday special on their 2018 models), proving that electric bikes don’t have to be over $2,000 to have the amenities and quality you need for daily commuting. Of course, that’s still a steep price for some. But as prices keep dropping in the e-bike industry, affordability breeds better access, and this might be the key that our cities—and their traffic—so desperately need.
While falling gas prices have temporarily halted years of gains in the number of bicycle commuters, more and more of us are using the bicycle to get around. It’s economical, provides good exercise, and is much cheaper than owning a car. But unless you’re in really good shape, you aren’t going to get very far. Enter the electric bike: a glorious new contraption allows us to get around without having to worry about arriving at our destinations a sweaty mess.
State and Local Laws dictate your use, but cannot constitutionally supersede the federal law – Any ebike purchased within the 750W/20mph limits has no fear of being under federal motor vehicle classification, nor can any state classify them a motor vehicle. The ebike is considered a ‘bicycle’ for consumer purposes. However, the State Laws on local bike paths and local thruways may prohibit or limit ebike access. When bike path signs use word such as ‘motor vehicles’ and ‘motorbikes’ , the laws are likely referring to gas-ICE motorbikes/dirt bikes/scooters, and not ebikes. Other references to ‘motorized bicycles’ or ‘motorized vehicles’ sound more inclusive and probably are intended for either ebikes or gas mopeds. If in doubt, you always have the option to pedal unassisted by completely powering your bike down. Even though Federal law grant ebikes a bicycle status, the common consensus found in my research allows local and state law to add additional regulation to pathway and road access, just because “it has a motor”. So the Federal laws protects the consumer from the burden of motor vehicle requirements, but not the restrictions to local and state right of ways enjoyed by all non-motored bicycles.
All classes of electric-assisted bicycles may be operated on a fully controlled limited access highway. Class 1 and 2 electric bicycles can be used on sidewalks, but Class 3 bicycles "may not be used on a sidewalk unless there is no alternative to travel over a sidewalk as part of a bicycle or pedestrian path."[143] Generally a person may not operate an electric-assisted bicycle on a trail that is designated as non-motorized and that has a natural surface, unless otherwise authorized.

Bicycles offer an important mode of transport in many developing countries. Until recently, bicycles have been a staple of everyday life throughout Asian countries. They are the most frequently used method of transport for commuting to work, school, shopping, and life in general. In Europe, bicycles are commonly used.[67] They also offer a degree of exercise to keep individuals healthy.[68]
Photo: Could solar power be the future of electric bicycles? The large solar panel mounted over the back wheel of this experimental bike powers an electric motor connected by a chain drive to the back wheel, helping the rider when he doesn't feel like pedaling. Using clean, green solar power would remove the problem of having to charge electric bikes with electricity generated from fossil fuels—and help to extend their range significantly. Photo by Warren Gretz courtesy of US DOE/NREL.

Under the statute, mopeds must be registered. To be registered under Hawaii law a moped must bear a certification label from the manufacturer stating that it complies with federal motor vehicle safety standards (FMVSS). A moped must also possess the following equipment approved by the D.O.T. under Chapter 91: approved braking, fuel, and exhaust system components; approved steering system and handlebars; wheel rims; fenders; a guard or protective covering for drive belts, chains and rotating components; seat or saddle; lamps and reflectors; equipment controls; speedometer; retracting support stand; horn; and identification markings.

This is an unofficial guide to the laws governing electric bicycles in the United States as of 2016. It was contributed by a guest writer The Smart Ped`aleck who was paid and remains unaffiliated with any electric bicycle company. It may be updated ongoing and is cited throughout with reference links and attributions at the end. It is designed to be an entertaining starting point for understanding the space, digging deeper and in turn choosing the best electric bike platform for your needs.

This little bike is great I weight like 175 and it's just great it can go up hills and it's an awesome little bike for NYC cops give me no issues and with a phone mount you can see your speed and battery life you have left... It's just a great bike nice and light I can pick up with one hand and it folds. The only cons I would say is I wish the battery lasts longer I get around 6.5 miles at full throttle at varying terrain and the horn is weak, I installed an air horn on my bike


Bicycles are popular targets for theft, due to their value and ease of resale.[113] The number of bicycles stolen annually is difficult to quantify as a large number of crimes are not reported.[114] Around 50% of the participants in the Montreal International Journal of Sustainable Transportation survey were subjected to a bicycle theft in their lifetime as active cyclists.[115] Most bicycles have serial numbers that can be recorded to verify identity in case of theft.[116]
The Wavecrest Tidalforce M-750 was based on The original military experimental M-313 model had a 1000 watt electric hub motor mounted into the rear wheel of a folding Montague Bicycles Paratrooper Bicycle frame and a 36 volt battery pack mounted into the front wheel hub. The later commercial versions had speed restrictions to comply with federal law with 750 watt restrictions (500 watts maximum in the Canadian version) but had 1000 watt unresricted speed as an add on option. The M-313/M-750X was the first electric bike to be made and tested by Wavecrest labs. It is based on a design developed for the Defense Advanced Research Projects Agency (DARPA) that was meant to allow zero-heat long distance troop movements for the United States Marine Corps in Afghanistan.
On the topic of visibility, there are a lot of things you can do to make yourself easier to see. You can throw on a reflective vest, for example, which has the added benefit of protecting your work clothes from flying dirt and debris. You can also add lights and reflectors to the bike itself, or strap illuminated bands to your arms and ankles. Both Gestalt theory and several biking visibility studies suggest that moving light sources like the reflectors on pedals that go up and down, are more visible to drivers because our visual systems are designed to pick up on movement (that of prey and predators evolutionarily), making reflective biking shoes a great idea.

Whether the terrain is flat or hilly impacts the distance you can travel, as does the weight of the bike, your own weight, the gearing available on the bike, and how much juice you give it. We suggest that a distance of 10 to 20 miles is a realistic expectation. Of course, if you're prepared to do at least some pedaling, you can extend that dramatically.
Controllers for brushless motors: E-bikes require high initial torque and therefore models that use brushless motors typically have Hall sensor commutation for speed and angle measurement. An electronic controller provides assistance as a function of the sensor inputs, the vehicle speed and the required force. The controllers generally allow input by means of potentiometer or Hall Effect twist grip (or thumb-operated lever throttle), closed-loop speed control for precise speed regulation, protection logic for over-voltage, over-current and thermal protection. Bikes with a pedal assist function typically have a disc on the crank shaft featuring a ring of magnets coupled with a Hall sensor giving rise to a series of pulses, the frequency of which is proportional to pedaling speed. The controller uses pulse width modulation to regulate the power to the motor. Sometimes support is provided for regenerative braking but infrequent braking and the low mass of bicycles limits recovered energy. An implementation is described in an application note for a 200 W, 24 V Brushless DC (BLDC) motor.[43]

Historically, materials used in bicycles have followed a similar pattern as in aircraft, the goal being high strength and low weight. Since the late 1930s alloy steels have been used for frame and fork tubes in higher quality machines. By the 1980s aluminum welding techniques had improved to the point that aluminum tube could safely be used in place of steel. Since then aluminum alloy frames and other components have become popular due to their light weight, and most mid-range bikes are now principally aluminum alloy of some kind.[where?] More expensive bikes use carbon fibre due to its significantly lighter weight and profiling ability, allowing designers to make a bike both stiff and compliant by manipulating the lay-up. Virtually all professional racing bicycles now use carbon fibre frames, as they have the best strength to weight ratio. A typical modern carbon fiber frame can weighs less than 1 kilogram (2.2 lb).
I'm one of the hardcore cyclists at Ars, along with Jay Timmer and his new-as-of-last-fall road bike as well as copyeditor Kerry Staurseth. I love cycling, and it was a major factor in my dropping 120lb over a 12-month period starting in the summer of 2009. My daily rider/errand-runner is a 1998 Gary Fisher Marlin mountain bike. For longer rides, I use my 2009 Trek XO2 cyclecross bike. I've made a few modifications to it, including removing the bumpy cyclecross tires and swapping out the front 46-tooth chainring for a 50-tooth one. I went with a cross bike over a road bike because I'm still a Clydesdale, and I like the slightly longer wheelbase of a cross bike. I've also briefly owned a 2011 Trek Madone 5.9, which I sold not long after I bought it due to severely screwing up my right knee.
E-bikes can be a useful part of cardiac rehabilitation programmes, since health professionals will often recommend a stationary bike be used in the early stages of these. Exercise-based cardiac rehabilitation programmes can reduce deaths in people with coronary heart disease by around 27%;[55] and a patient may feel safer progressing from stationary bikes to e-bikes.[56] They require less cardiac exertion for those who have experienced heart problems.[57]
Range is a key consideration with e-bikes, and is affected by factors such as motor efficiency, battery capacity, efficiency of the driving electronics, aerodynamics, hills and weight of the bike and rider.[36][37] Some manufacturers, such as the Canadian BionX or American Vintage Electric Bikes,[38] have the option of using regenerative braking, the motor acts as a generator to slow the bike down prior to the brake pads engaging.[39] This is useful for extending the range and the life of brake pads and wheel rims. There are also experiments using fuel cells. e.g. the PHB. Some experiments have also been undertaken with super capacitors to supplement or replace batteries for cars and some SUVS. E-bikes developed in Switzerland in the late 1980s for the Tour de Sol solar vehicle race came with solar charging stations but these were later fixed on roofs and connected so as to feed into the electric mains.[40] The bicycles were then charged from the mains, as is common today. While ebike batteries were produced mainly by bigger companies in past, many small to medium companies have started using innovative new methods for creating more durable batteries. State of the art, custom built automated precision CNC spot welding machines[41] created 18650 battery packs[42] are commonly used among Do-it-yourself ebike makers.
In Nova Scotia power-assisted bicycles are classified similarly to standard pedal bicycles. The Nova Scotia Motor Vehicle Act defines a power-assisted bicycle as a bicycle with an electric motor of 500 watts or less, with two wheels (one of which is at least 350 mm) or four wheels (two of which are at least 350mm). PABs are permitted on the road in the province of Nova Scotia as long as you wear an approved bicycle helmet with the chinstrap engaged. They do not have to meet the conditions defined within the Canadian Motor Vehicle Safety Regulations for a motorcycle (they are not classed as "motor vehicles"), but they do have to comply with federal regulations that define Power Assisted Bicycles.
Photo: Zap Electric's power-assist kit turns a conventional bike into an electric one. There's a bolt-on DC electric motor (weighing just over 3kg or 7lb) just above the back wheel, behind the police officer's foot, pressing against the tire and driving it by simple friction. The motor's powered by a compact lead-acid battery (weighing about 5.5 kg or 12 lb) inside a protective nylon bag. This kit adds quite bit of weight to the bike, but gives extra range and speed when needed. Photo taken in Santa Rosa, California by Rick Tang courtesy of US DOE/NREL.

A new electric cyclist will likely experience two conflicts of thought: 1). Will the general public accept my use of this power assist technology, or Will they ridicule and reject me as being lazy? 2). Will I stand out to law enforcement by the look of my bike or riding a bit faster than other cyclist on hills and roads? Grappling with these two thoughts will tempt most folks to try and remain unnoticed and ride more responsibly. After I became an advocate of e-transportation on two wheels, enjoying the benefits of power assist commuting, I eventually was a bit put off by this federal law, especially the 20mph limitation. Is 20 mph really practical and justified? Is it not true that many active young people on typical road bicycles are able to actively ride in the 20-25mph range? I discovered that ebikes, with larger tires and disk brakes, can comfortably and safety cruise in that range of speed. The standard 2001 Federal law of 20mph, eventually became a practical limitation for an ebike commuter of over 20 miles a day, and caused me to get a bike beyond the federal limits, making me more alert and sensitive when riding in the presence of the police.
Play it Safe, Make it Easy – E-bike manufacturers will offer you a large variety of styles, types, colors and utility, but the base specifications will be a bike producing less than 750 watts of power (1 horsepower = 746W) , and have its speed limited to 20mph on motor power alone. The majority of US ebikes meet that specification. Manufacturers do this for their own liability. Going this route assures you that your bike was built and sold legally. As a result, you will have about every privilege that a normal bicycle can expect. However, state and local laws may dictate reduced speeds and limited access to bike paths.
Great bike. Easy to assemble by yourself but if you have a rack let pros do it. No charge for that. Contacted the Addmotor people a few times and they got back quickly even on weekends. Great service. Bike is solid as a rock and excellent components. Only drawback is lack of fenders which I hope someone can manufacture. I would buy again in a nano second!
The Freedom’s motor gives you five different levels of boost, and the 36-volt battery offers up to 35 miles of range. You can track your power level and speed, as well as your battery life, on a digital display mounted to the handlebar. I have to admit I spent nearly all my time on the Freedom riding in the highest level, where I could pedal up to 19 mph to 20 mph without even breaking a sweat.
During the course of its evolution, the Specialized Levo has helped shape the world of eMTBing. When it was introduced, it set the benchmark in riding dynamics and integration. Now Specialized has completely redesigned the bike and put it on 29″ wheels. The integration has been improved yet again, the battery capacity has been increased and the handling has been refined. We were thrilled with our first test ride. Anyone looking for a new bike next year for maximum trail performance should definitely take a closer look at the new Levo! We’re already looking forward to our big group test of the best bikes of 2019 early next year.
The time or distance an electric bike battery will run between chargings is impossible to judge with much accuracy. There are too many variables: terrain, speed, rider weight, bike load (shopping, kids, luggage), and more. However, we can make a few generalizations about an e-bike’s recharge time and overall working life. These generalizations should be used for comparison purposes only.
What's the Centros like? Big and heavy, but with enough power to overcome that, it really reminded me of a more upmarket Volt Pulse. You do tend to find that the weightier e-bikes give more of a feeling of speed, even though you're only doing 20mph or so at the absolute most (only up to 15mph with electrical assistance so you'll need leg muscles or a downward incline to get to that outlandish velocity).
© 2019 Condé Nast. All rights reserved. Use of and/or registration on any portion of this site constitutes acceptance of our User Agreement (updated 5/25/18) and Privacy Policy and Cookie Statement (updated 5/25/18) and Ars Technica Addendum (effective 8/21/2018). Ars may earn compensation on sales from links on this site. Read our affiliate link policy.
×