EU: EN15194 (EPAC – Electrically Power Assisted Cycles) defines the use pedal-assisted less than 25k/h bikes: "Cycles with pedal assistance which are equipped with an auxiliary electric motor having a maximum continuous rated power of 0.25 kW, of which the output is progressively reduced and finally cut off as the vehicle reaches a speed of 25 km/h or if the cyclist stops pedaling.”

I converted my Kona Dew Deluxe to electric with a controller and 1000 watt front wheel. The SLA batteries I tried initially were _functional_, but the bike had a range of about 6 miles @ approx. 50% throttle use. Since upgrading to the Joyisi pack, the utility of the bike has increased exponentially. I need to add a better gauge so I can drain the battery more fully between charges, but I'm getting at least 20 miles per charge, including some very aggressive uphill segments. On flat ground, the battery powers the bike to approx. 35MPH; even on really steep hills with minimal pedal assist, I do at least 15MPH. Biking 15MPH uphill with little/no effort is EPIC.
We need to support and put our purchasing power behind ebikes sold in the U.S. that are trying to comply with the California rules which allow 500w and 750w nominal motors and establish 3 classes. If these bikes can create a big enough footprint in the market then future U.S. bike rules may universally adopt these standards. It is better than engaging in regulation showdowns without any standardized and unified proposal on the part of the Electric Bike Community.
As of 2005, where Federal funds have been used in the construction of bicycle or pedestrian paths motor vehicles including electric bicycles (here defined as having a motor weighing less than Template:Convert) are not permitted unless State or Local regulations permit [25]. This was known as the Transportation Equity Act for the 21st Century (TEA-21), or Public Law 105-178, or by its 2003 re-authorization which expired in 2005 the Safe, Accountable, Flexible, Efficient Transportation Equity Act (SAFETEA-LU).[26][27]
State and Local Laws dictate your use, but cannot constitutionally supersede the federal law – Any ebike purchased within the 750W/20mph limits has no fear of being under federal motor vehicle classification, nor can any state classify them a motor vehicle. The ebike is considered a ‘bicycle’ for consumer purposes. However, the State Laws on local bike paths and local thruways may prohibit or limit ebike access. When bike path signs use word such as ‘motor vehicles’ and ‘motorbikes’ , the laws are likely referring to gas-ICE motorbikes/dirt bikes/scooters, and not ebikes. Other references to ‘motorized bicycles’ or ‘motorized vehicles’ sound more inclusive and probably are intended for either ebikes or gas mopeds. If in doubt, you always have the option to pedal unassisted by completely powering your bike down. Even though Federal law grant ebikes a bicycle status, the common consensus found in my research allows local and state law to add additional regulation to pathway and road access, just because “it has a motor”. So the Federal laws protects the consumer from the burden of motor vehicle requirements, but not the restrictions to local and state right of ways enjoyed by all non-motored bicycles.
No endorsement is required on a driver license in order to operate a motorized bicycle, thus the motorized bicycle may be operated by anyone with a valid driver license. Goggles, windshields and other special equipment required for motorcycles and motor-driver cycles are not required for operation of a motorized bicycle. However, crash helmets are required regardless of operators age. Minors between the ages of 14 and 16 may apply for a restricted license to operate a motorized bicycle, just as they would to operate a motor-driver cycle. For instance, they must take a written test, vision tests and demonstrate their ability to operate the motorized bicycle. The license issued will be restricted to a motorized bicycle only. The license is valid only during daylight hours and within a seven-mile (11 km) radius of the driver's home. Applicants for any type of license less than eighteen (18) years old, must complete a Minor/Teen-age Affidavit and Cancellation form making the parent or legal guardian financially liable for the applicants action. [57]
We Can Build It.   Built by hand in Pennsylvania, mostly by Harry and Alec. Custom Wheelbuilding Some people don't know that we build every one of our wheels here by hand in Pennsylvania. This lets us control each step of the process, ensuring that the spokes are uniform, straight, and undamaged, allowing us to apply spoke-prep to the spokes, oil to the nipple seats, and inspect the rims before we use them. We get the tension, dish, lateral and radial trueness dialed in to our standards and know it's a good wheel before it goes out the door.

"Medical Exemptions" are also a standard right in the State of Texas for motorcycles & even bicyclists. Through Texas's motorcycle helmet law (bicycle helmet laws from city ordinances), it is only required for those 21 years old or younger to wear a helmet. However, a medical exemption,[133][134][135][136][137] written by a certified licensed medical physician or licensed chiropractor, which exempts one from wearing a helmet, can be used for bicyclists if helmets are required.


The dwarf ordinary addressed some of these faults by reducing the front wheel diameter and setting the seat further back. This, in turn, required gearing—effected in a variety of ways—to efficiently use pedal power. Having to both pedal and steer via the front wheel remained a problem. Englishman J.K. Starley (nephew of James Starley), J.H. Lawson, and Shergold solved this problem by introducing the chain drive (originated by the unsuccessful "bicyclette" of Englishman Henry Lawson),[25] connecting the frame-mounted cranks to the rear wheel. These models were known as safety bicycles, dwarf safeties, or upright bicycles for their lower seat height and better weight distribution, although without pneumatic tires the ride of the smaller-wheeled bicycle would be much rougher than that of the larger-wheeled variety. Starley's 1885 Rover, manufactured in Coventry[26] is usually described as the first recognizably modern bicycle.[27] Soon the seat tube was added, creating the modern bike's double-triangle diamond frame.

Louisiana Revised Statute R.S. 32:1(41) defines a motorized bicycle as a pedal bicycle which may be propelled by human power or helper motor, or by both, with a motor rated no more than one and one-half brake horsepower, a cylinder capacity not exceeding fifty cubic centimeters, an automatic transmission, and which produces a maximum design speed of no more than twenty-five miles per hour on a flat surface. Motorized bicycles falling within this definition must be registered and titled under Louisiana law. Additionally, a motorized bicycle operated upon Louisiana roadways or highways by a person fifteen years of age or older and producing more than five horsepower must possess a valid driver's license with a motorcycle endorsement and adhere to laws governing the operation of a motorcycle, including the wearing of approved eye protectors or a windshield and the wearing of a helmet. The statute also states that "Motorized bicycles such as pocket bikes and scooters that do not meet the requirements of this policy shall not be registered."

"Electric power-assisted bicycle" means a vehicle that travels on not more than three wheels in contact with the ground and is equipped with (i) pedals that allow propulsion by human power and (ii) an electric motor with an input of no more than 1,000 watts that reduces the pedal effort required of the rider. For the purposes of Chapter 8 of this title, an electric power-assisted bicycle shall be a vehicle when operated on a highway.[142]

Bicycles offer an important mode of transport in many developing countries. Until recently, bicycles have been a staple of everyday life throughout Asian countries. They are the most frequently used method of transport for commuting to work, school, shopping, and life in general. In Europe, bicycles are commonly used.[67] They also offer a degree of exercise to keep individuals healthy.[68]
No endorsement is required on a driver license in order to operate a motorized bicycle, thus the motorized bicycle may be operated by anyone with a valid driver license. Goggles, windshields and other special equipment required for motorcycles and motor-driver cycles are not required for operation of a motorized bicycle. However, crash helmets are required regardless of operators age. Minors between the ages of 14 and 16 may apply for a restricted license to operate a motorized bicycle, just as they would to operate a motor-driver cycle. For instance, they must take a written test, vision tests and demonstrate their ability to operate the motorized bicycle. The license issued will be restricted to a motorized bicycle only. The license is valid only during daylight hours and within a seven-mile (11 km) radius of the driver's home. Applicants for any type of license less than eighteen (18) years old, must complete a Minor/Teen-age Affidavit and Cancellation form making the parent or legal guardian financially liable for the applicants action. [57]
Put the wheel with the electric hub on your bike and connect the brake components. Simply reverse the process you used to remove the wheel in order to reinstall it. Be sure to adjust the chain so it fits properly if you’re replacing the back wheel. If the bike has rim or cantilever brakes, simply close them over the new wheel using the lever. If the bike has disc brakes, put the pads back in place and secure them using the clips, springs, or cotter or retaining pin.[11]
In conformance with legislation adopted by the U.S. Congress defining this category of electric-power bicycle (15 U.S.C. 2085(b)), CPSC rules stipulate that low speed electric bicycles[64] (to include two- and three-wheel vehicles) are exempt from classification as motor vehicles providing they have fully operable pedals, an electric motor of less than 750W (1 hp), and a top motor-powered speed of less than 20 miles per hour (32 km/h) when operated by a rider weighing 170 pounds.[65] An electric bike remaining within these specifications is subject to the CPSC consumer product regulations for a bicycle. Commercially manufactured e-bikes exceeding these power and speed limits are regulated by the federal DOT and NHTSA as motor vehicles, and must meet additional safety requirements. The legislation enacting this amendment to the CPSC is also known as HR 727.[66] The text of HR 727 includes the statement: "This section shall supersede any State law or requirement with respect to low-speed electric bicycles to the extent that such State law or requirement is more stringent than the Federal law or requirements." (Note that this refers to consumer product regulations enacted under the Consumer Product Safety Act. Preemption of more stringent state consumer product regulations does not limit State authority to regulate the use of electric bicycles, or bicycles in general, under state vehicle codes.)
Bicycles offer an important mode of transport in many developing countries. Until recently, bicycles have been a staple of everyday life throughout Asian countries. They are the most frequently used method of transport for commuting to work, school, shopping, and life in general. In Europe, bicycles are commonly used.[67] They also offer a degree of exercise to keep individuals healthy.[68]
China's experience, as the leading e-bike world market, has raised concerns about road traffic safety and several cities have considered banning them from bicycle lanes.[2] As the number of e-bikes increased and more powerful motors are used, capable of reaching up to 30 miles per hour (48 km/h), the number of traffic accidents have risen significantly in China. E-bike riders are more likely than a car driver to be killed or injured in a collision, and because e-bikers use conventional bicycle lanes they mix with slower-moving bicycles and pedestrians, increasing the risk of traffic collisions.[2]

Torque sensors and power controls were developed in the late 1990s. For example, Takada Yutky of Japan filed a patent in 1997 for such a device. In 1992 Vector Services Limited offered and sold an e-bike dubbed Zike.[9] The bicycle included NiCd batteries that were built into a frame member and included an 850 g permanent-magnet motor. Despite the Zike, in 1992 hardly any commercial e-bikes were available.
I would add that the point of the article seems to encourage ebikers to “know the state laws” and be confident within those boundaries. To D McCarthy’s question, if your state has a definition for ebikes and classifies them as bicycles and affords access as bicycles, AND, your particular ebike is built within those specifications, then you should be able to ride that section of road with confidence. Just my 2C.
Some argue, that an ebike should have some kind of front suspension, i.e. be able to cope with potholes at higher speed or off-road conditions. However, in countries with flat roads (e.g. Switzerland, Germany or Holland) you don't need that extra weight for extra price if you stay on roads and/or drive slowly in difficult terrain. Some makes (like the Stromer) let you choose.

Operators are subject to driving rules and equipment requirements (if applicable) when operated on the public streets or highways (which includes the main traveled portion of the road, shoulder and sidewalk). This means that an operator could be cited for speeding, failure to signal, unsafe change of course, driving on the sidewalk, DWI (this would apply to anywhere in the state and not just the streets/highways), and all other driving rules contained within state law that would apply. They may also not ride more than two abreast and may not impede the normal and reasonable movement of traffic. On a laned roadway, they must operate within a single lane.[citation needed]
Did you know that electric bikes can be used for fitness training? Or that they have been scientifically proven to increase the amount of cycling people do? Or that they have proven health and fitness benefits? Well, it’s all true! Apart from being tons of fun, ebikes can be used to improve health and fitness in many ways. Here are our top posts about how ebikes can improve your health and fitness.
We've also released our first native 72V battery pack in a conventional downtube battery casing, assembled using the high power Samsung 27100 40T cells so that even with the small 8Ah capacity it is able to deliver 40-50A continuous currents. This is an ideal battery for fast and sporty offroad ebike builds, allowing powerful performance without the weight or complexity of most 72V setups (either two 36V packs in series or a large triangle frame battery).
A KS LEV Integra dropper post, 130mm of front and rear travel, 27.5-inch wheels, and trail-grabbing 2.8-inch tires make this pedal-assist mountain bike a great option if you want to climb farther to shred longer, but don’t want to lug your bike uphill for ages. The 250-watt motor, placed slightly farther forward than most other bikes to optimize weight distribution and handling, provides a nice boost so you can enjoy the ride up and not be too gassed when you get to the top.

Whether squeezing onto the 4 train or pedaling through Lower Manhattan, I notice a few curious glances at the bike with the big battery in the center of the frame. This is not surprising; e-bikes are huge practically everywhere but the US. According to the latest figures from the Confederation of the European Bicycle Industry, e-bike growth in the UK is up from 40,000 units in 2016 to 63,000 in 2017.


Both the Stromer and the Stoeckli are very nice looking designs and easy to handle. Reliability for both does not seem to be up to Swiss standards, e.g. some of the 2012 Stöcklis seem to have bad contacts. However, as of 2013, most of these problems should be fixed. The Cube got criticized for its battery/saddle system, but this has probably been fixed in more recent edition and it has less "punch" then the other's since the motor is smaller (324W?). I don't know about the BH Neo Nitro. Given the relatively low price of the BH Nitro, it may be the best buy in this category if you plan to cover smaller distances (the battery is limited to 9Ah, and Spain's industry does need some help ;) Anyhow, all of these models come with a variety of motors and country-specific modifications. E.g. in France, the BH Nitro comes with a 350W motor and is electronically limited to 25km/h, whereas in Switzerland you either can get a 500W - 45 km/h version or a 250W? - 25km/h version.
The drivetrain begins with pedals which rotate the cranks, which are held in axis by the bottom bracket. Most bicycles use a chain to transmit power to the rear wheel. A very small number of bicycles use a shaft drive to transmit power, or special belts. Hydraulic bicycle transmissions have been built, but they are currently inefficient and complex.

European Union directive 2002/24/EC exempts vehicles with the following definition from type approval: "Cycles with pedal assistance which are equipped with an auxiliary electric motor having a maximum continuous rated power of 0.25 kW, of which the output is progressively reduced and finally cut off as the vehicle reaches a speed of 25km/h (15.5mph) or if the cyclist stops pedaling." This is the de facto definition of an electrically assisted pedal cycle in the EU. As with all EU directives, individual member countries of the EU are left to implement the requirements in national legislation.

In Quebec power-assisted bicycles are often classified similarly to standard pedal bicycles. They do not have to meet the conditions defined within the Canadian Motor Vehicle Safety Regulations (they are not classed as "motor vehicles"), but they do have to comply with federal regulations that define Power Assisted Bicycles. The Quebec Highway Safety Code defines a power-assisted bicycle as a bicycle with an electric motor. PABs are permitted on the road in the province of Quebec.
While we won't be there in person, a number of vehicles will be at the show featuring the new Grin products like the GMAC Hub Motors, RH212 direct drive motors, All Axle hubs, and the Baserunner and Phaserunner_L10 controllers.  If you're lucky enough to attend then check out Booth A.18 and Booth 3.12 for some velomobiles and cargo vehicles running this gear.  

If you're more concerned with conquering the countryside than the commute, Cyclotricity's Stealth is the one for you. It's a full-size mountain bike, with aggressive tyres and suspension on the front forks to absorb the rocks and bumps on the trails. It's comfortable to ride, and its motor can either give you assistance while you ride, or you can just hit the throttle to rocket over hills with no effort on your part.

The batteries are the most important parts of the bike, because (if you don't do any pedaling) they contain all the power that will drive you along. Typical electric bike batteries make about 350–500 W of power (that's about 35–50 volts and 10 amps), which is about a quarter as much as you need to drive an electric toaster. In theory, you could use any kind of battery on a bicycle. In practice, however, you want to use something that stores lots of power without being too heavy—or you'll be using half your power just moving the battery along! That tends to rule out heavy lead-acid batteries like the ones that start cars, though some electric bikes do use them. Lightweight lithium-ion batteries, similar to those used in laptop computers, mobile (cellular) phones, and MP3 players, are now the most popular choice, though they're more expensive than older rechargeable battery technologies such as nickel-cadmium ("nicad"). Typical batteries will give your bicycle a range of 10–40 miles between charges (depending on the terrain) and a top speed of 10–20 mph (which is about the maximum most countries allow for these vehicles by law). You can extend the range by pedaling or free-wheeling some of the time.
"Moped" means a device upon which a person may ride which has two or three wheels in contact with the ground, a motor having a maximum power output capability measured at the motor output shaft, in accordance with the Society of Automotive Engineers standards, of two horsepower (one thousand four hundred ninety -two watts) or less and, if it is a combustion engine, a maximum piston or rotor displacement of 3.05 cubic inches (fifty cubic centimeters) and which will propel the moped, unassisted, on a level surface at a maximum speed no greater than thirty miles per hour; and a direct or automatic power drive system which requires no clutch or gear shift operation by the moped driver after the drive system is engaged with the power unit.

The Espin is powered by a 350-watt motor that’s rated for trips up to 50 miles (depending on the terrain and assist level). Once depleted, the battery fully charges in roughly five hours. Thankfully, Espin makes it easy to remove the battery, allowing you to quickly recharge it at home or in the office between trips. A backlit LCD control hub displays your basic metrics and battery life while in transit and LED headlights add a touch of light when needed.
We spent 45 hours on research, videography, and editing, to review the top choices for this wiki. With rechargeable, battery-powered pedaling assistance, electric bicycles offer an increasingly viable alternative to fossil-fueled commuting, and e-bikes enable riders of various abilities to extend their cycling range. But the street legality of these hybrid machines remains a contentious issue, so be sure to check current state and local laws governing their operation before you hit the road. When users buy our independently chosen editorial picks, we may earn commissions to support our work. Skip to the best electric bike on Amazon.

The recommendation depends a lot on what you plan to use the bike for and how you plan to ride. That said, I would recommend at least a 750 (if not 1,000) watt motor, and, if you want reasonable range, 48 or 52v cells with a minimum rating of 19ah. For shorter rides, you can use a smaller battery. Multiply battery voltage by amp hour rating to get battery watt hours. Divide the watt hours by the motors power rating to get a general idea of how many hours of heavy use you might get. I’d also recommend a mid drive as opposed to a hub drive, or to find a hub drive wheel rated to take your and the bicycle's combined weight.
This is an unofficial guide to the laws governing electric bicycles in the United States as of 2016. It was contributed by a guest writer The Smart Ped`aleck who was paid and remains unaffiliated with any electric bicycle company. It may be updated ongoing and is cited throughout with reference links and attributions at the end. It is designed to be an entertaining starting point for understanding the space, digging deeper and in turn choosing the best electric bike platform for your needs.
We bought 2 of these to go along with our AW 26"x1.75" Front Wheel Electric Bicycle Motor Kits and they work perfectly! The batteries that came with and were recommended by the wheel manufacturer were "clunky", had to be mounted in hanging bags and just didn't work well. These Li-ion Battery with Battery Holders are sleek, fit our Beach Cruisers perfectly, give us a rack to carry our "beach stuff" and one of the best features is how easy they are to charge! They lock in place when we are out and about, but I can unlock them, slide them both out and take them into the RV for charging when we return. Very happy with these and would recommend to anyone looking to convert their current bike into e-bikes!
This year was busy at Haibike’s EUROBIKE stand. The reason: the new FLYON series, which we could only admire behind glass. The new bikes are the spearhead of Haibike’s eMTB development with an exciting and unprecedented level of integration and connectivity. They have a specially developed display, their own remote and, thanks to a 5,000 lumen headlight, are able to turn night into day. To make the rider visible at all times, taillights are neatly integrated into the frame. The bikes also come with the most powerful motor currently available on the market, from TQ Systems. We are sure that many will buy this bike not only for its performance but also as a status symbol.
"Moped" means a device upon which a person may ride which has two or three wheels in contact with the ground, a motor having a maximum power output capability measured at the motor output shaft, in accordance with the Society of Automotive Engineers standards, of two horsepower (one thousand four hundred ninety -two watts) or less and, if it is a combustion engine, a maximum piston or rotor displacement of 3.05 cubic inches (fifty cubic centimeters) and which will propel the moped, unassisted, on a level surface at a maximum speed no greater than thirty miles per hour; and a direct or automatic power drive system which requires no clutch or gear shift operation by the moped driver after the drive system is engaged with the power unit.
×