The Class 3 Aventon Pace 500 urban e-bike has five levels of pedal assist and tops out at 28 mph. But the Pace has something not found on a lot of modern e-bikes. In addition to pedal power, it also has a throttle—in the case of the Pace, a small thumb paddle on the left side of the handlebar next to the control unit that holds at a steady 20 mph, no pedaling required. The bike itself has an aluminum frame, a swept-back handlebar, ergo grips, a sturdy kickstand, hydraulic disc brakes, 8-speed Shimano Altus shifting and gearing, 27.5x2.2-inch Kenda e-bike-rated tires, a saddle the size of Texas, and good ol’ classic city/commuter-bike geometry. It doesn’t come equipped with fenders or a rear rack, but you can add them. Power comes in the form of a 500-watt rear-hub motor, a semi-integrated battery on the down tube (with a range of up to 50 miles), and a backlit display unit mounted on the stem.
But electric bicycles—e-bikes—are new territory for me. Broadly speaking, there are two basic options in e-bike land: power-on-demand and pedal-assist. With the former, the rider can control the speed with a throttle instead of just pedaling. Think moped but with an electric motor instead of internal combustion. Pedal-assist, by contrast, requires the rider to do some of the work. The electric motor won't engage unless the rider is pedaling.
Electric bicycles are not allowed in any public area, meaning an area where there is full or partial public access. Any kind of pedal assist, electric bike, scooter, moped or vehicle which has any form of propulsion, whether in full or as assist, other than human power, must be approved as either a car, motorcycle, van, truck, bus or similar. This makes pedelecs and tilt-controlled two-wheel personal vehicles illegal in all practical ways, as they cannot be registered as a motor cycle.
Class 1 makes great inroads to establish set boundaries for off road/natural surface trail access for eMountain bikes. There is fierce resistance from some mountain biking purists to allow ebikes on trails. BPSA and IMBA have done good work to justify the impact of class 1 ebikes on natural surface trails, and eliminate the wear-n-tear argument, though IMBA members are not 100% on board.
Depending on local laws, many e-bikes (e.g., pedelecs) are legally classified as bicycles rather than mopeds or motorcycles. This exempts them from the more stringent laws regarding the certification and operation of more powerful two-wheelers which are often classed as electric motorcycles. E-bikes can also be defined separately and treated under distinct Electric bicycle laws.
I would add that the point of the article seems to encourage ebikers to “know the state laws” and be confident within those boundaries. To D McCarthy’s question, if your state has a definition for ebikes and classifies them as bicycles and affords access as bicycles, AND, your particular ebike is built within those specifications, then you should be able to ride that section of road with confidence. Just my 2C.
An electric bike (also called e-bike, power-assist bike, pedelec…) is a fairly conventional bike combined with a battery and motor that helps out when you are pedaling to make it easier to get uphill or completely takes over driving and allows you to cruise along. Top quality electric bikes, along with electric scooters, are revolutionizing the bicycle industry. Not only is riding an e-bike simple and easy, but a rider can significantly extend their range with minimal cost or effort.
These are, unfortunately, small steps forward, however, as the majority of city streets in America aren’t bike-friendly, and new legislation is rarely enforced. Then, if you take a look at the fitness (or lack thereof) of the average American, a connection begins to develop. This connection becomes even stronger when you compare the biking system here with that of a country like Norway, which has devoted hundreds of millions of dollars to its biking infrastructure, building highways dedicated to the mode of transportation. As a result, Norway is one of the most physically active countries in the world, significantly lowering their incidences of heart disease and obesity.
Being member of European Economic Area (EEA), Norway implemented the European Union directive 2002/24/EC. This directive defined legal ebikes for all EU and EEA countries to "Cycles with pedal assistance which are equipped with an auxiliary electric motor having a maximum continuous rated power of 0.25 kW, of which the output is progressively reduced and finally cut off as the vehicle reaches a speed of 25 km/h or if the cyclist stops pedaling.” The definition became part of Norwegian vehicle legislation in 2003. A more detailed specification will become effective when the new European ebike product safety standard EN 15194 is published in 2009.
9. Terms: Electric Bike Technologies INC. reserves the right, in its sole discretion to cancel, terminate, modify or suspend the Sweepstakes should (in its sole discretion) a virus, bugs, non-authorized human intervention, fraud or other causes beyond its control corrupt or affect the administration, security, fairness or proper conduct of the Sweepstakes. In such case, Electric Bike Technologies INC. may select the recipients from all eligible entries received prior to and/or after (if appropriate) the action taken by Electric Bike Technologies INC.. Electric Bike Technologies INC. reserves the right at its sole discretion to disqualify any individual who tampers or attempts to tamper with the entry process or the operation of the Sweepstakes or website or violates these Terms & Conditions.
Historically, materials used in bicycles have followed a similar pattern as in aircraft, the goal being high strength and low weight. Since the late 1930s alloy steels have been used for frame and fork tubes in higher quality machines. By the 1980s aluminum welding techniques had improved to the point that aluminum tube could safely be used in place of steel. Since then aluminum alloy frames and other components have become popular due to their light weight, and most mid-range bikes are now principally aluminum alloy of some kind.[where?] More expensive bikes use carbon fibre due to its significantly lighter weight and profiling ability, allowing designers to make a bike both stiff and compliant by manipulating the lay-up. Virtually all professional racing bicycles now use carbon fibre frames, as they have the best strength to weight ratio. A typical modern carbon fiber frame can weighs less than 1 kilogram (2.2 lb).
Despite the illegal status in the state of New York, enforcement of this law varies at the local level. New York City enforces the bike ban with fines and vehicle confiscation for throttle activated electric bikes. However, Mayor Bill de Blasio has recently changed the city's official policy to legalize pedal-assist electric bikes that have a maximum speed limited to 20 mph.  Contrarily, Tompkins County supports electric bike usage, even providing grant money to fund electric bike share/rental projects.
While we're still fairly new to the solar ebike game, Mark is among the (suprisingly numerous) Grin customers who've been thinking about and experimenting with solar bikes for many years. After he shared pictures of his latest project and mentioned his round the world touring ambitions, we thought we had to do a small feature on this guy. A quick last minute trip to Maker Faire was arranged to meet up, and here we present, Mark Havran:
To qualify as an electric-assisted bicycle under state law they need to have a seat and fully operable pedals for human propulsion, meet federal motor vehicle safety standards, an electric motor that has a power output of not more than 1,000 watts, maximum speed of not more than 20 mph (electric motor and human power combined), disengages or ceases to function when the vehicle’s brakes are applied, two or three wheels