In conformance with legislation adopted by the U.S. Congress defining this category of electric-power bicycle (15 U.S.C. 2085(b)), CPSC rules stipulate that low speed electric bicycles[64] (to include two- and three-wheel vehicles) are exempt from classification as motor vehicles providing they have fully operable pedals, an electric motor of less than 750W (1 hp), and a top motor-powered speed of less than 20 miles per hour (32 km/h) when operated by a rider weighing 170 pounds.[65] An electric bike remaining within these specifications is subject to the CPSC consumer product regulations for a bicycle. Commercially manufactured e-bikes exceeding these power and speed limits are regulated by the federal DOT and NHTSA as motor vehicles, and must meet additional safety requirements. The legislation enacting this amendment to the CPSC is also known as HR 727.[66] The text of HR 727 includes the statement: "This section shall supersede any State law or requirement with respect to low-speed electric bicycles to the extent that such State law or requirement is more stringent than the Federal law or requirements." (Note that this refers to consumer product regulations enacted under the Consumer Product Safety Act. Preemption of more stringent state consumer product regulations does not limit State authority to regulate the use of electric bicycles, or bicycles in general, under state vehicle codes.)

But electric bicycles—e-bikes—are new territory for me. Broadly speaking, there are two basic options in e-bike land: power-on-demand and pedal-assist. With the former, the rider can control the speed with a throttle instead of just pedaling. Think moped but with an electric motor instead of internal combustion. Pedal-assist, by contrast, requires the rider to do some of the work. The electric motor won't engage unless the rider is pedaling.

Again, these are base level components here. The Shimano/TX55 gearing is fine for this application level but I have lost my chain a few times in a few weeks. The frame is surprisingly solid aluminum alloy which feels stiffer and lighter than last year’s Ancheer. The supplied front 10W light is very bright, however the back light is charged via USB and has a push button rather than being wired into the controller. The disc brakes are the same no-name brand as the Ancheer but appear to be a size bigger. The fork, while not amazing, is a big improvement in stiffness and give over the Ancheer’s, which scared me a bit.

Experiments done in Uganda, Tanzania, and Sri Lanka on hundreds of households have shown that a bicycle can increase a poor family's income as much as 35%.[69][better source needed][70][71] Transport, if analyzed for the cost-benefit analysis for rural poverty alleviation, has given one of the best returns in this regard. For example, road investments in India were a staggering 3–10 times more effective than almost all other investments and subsidies in rural economy in the decade of the 1990s. What a road does at a macro level to increase transport, the bicycle supports at the micro level. The bicycle, in that sense, can be an important poverty-eradication tool in poor nations.
The Alpha has a  36V Brose 50W motor which is fueled by a “bridging” lithium-ion battery with 150 Wh of capacity, which is charged by the onboard 150 W PEM Hydrogen fuel cell. The fuel cell is fueled by a 2 litre compressed hydrogen gas cylinder, which can be refilled in about 2 minutes at a filling station.  In terms of cost per charge, this is likely to be more than a standard electric bike, however, the convenience of faster recharging may make it suitable for some riders, particularly commercial fleet operators using ebikes on shifts for several riders.
The Christmas day is coming soon, since I receive the bike, it's about a week, and I am satisfied with it! just as advertised, very powerful and good design. the most important point is that once the battery is FULL CHARGE, how far it can reach up to. I have a funny test, in the normal road(not in the dramatic slope or uphill), it can goes almost 44 miles. That is what I give 5 star for this bike! very powerful with reasonable price!
The body is made from light and durable aluminum. The handlebar comes with simple controls to let you accelerate, brake, monitor battery life, operate headlights and of course…sound the horn. There’s even an USB point that will let you charge your iPhone or Android on the go. The bike can reach a top speed of 10mph. Feel the wind in your hair as you zoom up and down hills and past all that city traffic…

Catrike Expedition converted with a 26" Performance E-BikeKit This Catrike Expedition was a custom conversion done at Electric Bike Technologies in Croydon, PA. If you have a Catrike Expedition and wish to convert it on your own, the following may help. If you would like to purchase the kit and add-ons used in this conversion, you can now purchase a kit special for your Catrike from us online here, or by calling us up - we'll include extras to make the conversion go as smoothly as possible! you can order them from our online shop or call us at 866.882.3245 M-F 9am-5pm EST....

Parliament has decided to approve the speed pedelec – a type of super electric bike that can reach speeds of up to 45 km/hour – for riding on cycle paths. Danish Parliament has decided that as of July 1 2018 those operating the super bikes only need to have turned 15 and wear a helmet, while the licence and number-plate demands will no longer be in play. [38]
Conversion kits, on the other hand, are sold and installed separately on traditional bicycles. They are harder to setup and conceal, and require some basic mechanical ability and a little bit of ‘elbow grease’ to install. The advantage of conversion kits is that you can choose almost any standard bicycle, and you have the freedom to change or upgrade components as you go. A conversion kit will also allow you to achieve higher power and speed ratings that are not possible on most pre-built electric bike models. Kits are great for tall or heavy riders because they can opt for a larger bike, with higher power and weight carrying capacity. People living in hilly terrain may require the additional torque to handle extremely large inclines. For people who prefer a specific bike model or just love to go faster, a conversion kit offers enormous flexibility.

There are dozens of good 25Km/h pedelecs. Our advice is to go the nearest good e-bike store and get it from there, because e-bikes may need good support. Only if you like servicing a bike yourself is buying from the Internet a good option. As of Spring 2013, a good benchmark to compare with is the Austrian KTM Amparo also called KTM Severo 8M or the German Kalkhoff Impuls or Agattu series. It has a reliable Panasonic middle motor and a good battery. If you want a more sexy design, try the SMART from the urban car maker of the same name.
A new electric cyclist will likely experience two conflicts of thought: 1). Will the general public accept my use of this power assist technology, or Will they ridicule and reject me as being lazy? 2). Will I stand out to law enforcement by the look of my bike or riding a bit faster than other cyclist on hills and roads? Grappling with these two thoughts will tempt most folks to try and remain unnoticed and ride more responsibly. After I became an advocate of e-transportation on two wheels, enjoying the benefits of power assist commuting, I eventually was a bit put off by this federal law, especially the 20mph limitation. Is 20 mph really practical and justified? Is it not true that many active young people on typical road bicycles are able to actively ride in the 20-25mph range? I discovered that ebikes, with larger tires and disk brakes, can comfortably and safety cruise in that range of speed. The standard 2001 Federal law of 20mph, eventually became a practical limitation for an ebike commuter of over 20 miles a day, and caused me to get a bike beyond the federal limits, making me more alert and sensitive when riding in the presence of the police.
The safety bicycle gave women unprecedented mobility, contributing to their emancipation in Western nations. As bicycles became safer and cheaper, more women had access to the personal freedom that bicycles embodied, and so the bicycle came to symbolize the New Woman of the late 19th century, especially in Britain and the United States.[8][73] The bicycle craze in the 1890s also led to a movement for so-called rational dress, which helped liberate women from corsets and ankle-length skirts and other restrictive garments, substituting the then-shocking bloomers.[8]
Faster e-bikes usually run at higher voltage. But higher voltage reduces range as well, because lower speeds are more efficient. So e-bikes running higher voltage will have less range unless significantly more battery capacity is added to compensate. This causes higher speed builds to be increasingly expensive for the same range that could be gotten from a slower e-bike. Therefore deciding on a build requires balancing several factors: Range, Speed, Cost, and Quality.
Many newer or smaller companies only design and market their products; the actual production is done by Asian companies. For example, some 60% of the world's bicycles are now being made in China. Despite this shift in production, as nations such as China and India become more wealthy, their own use of bicycles has declined due to the increasing affordability of cars and motorcycles.[102] One of the major reasons for the proliferation of Chinese-made bicycles in foreign markets is the lower cost of labor in China.[103]
"Medical Exemptions" are also a standard right in the State of Texas for motorcycles & even bicyclists. Through Texas's motorcycle helmet law (bicycle helmet laws from city ordinances), it is only required for those 21 years old or younger to wear a helmet. However, a medical exemption,[133][134][135][136][137] written by a certified licensed medical physician or licensed chiropractor, which exempts one from wearing a helmet, can be used for bicyclists if helmets are required.
Controllers for brushless motors: E-bikes require high initial torque and therefore models that use brushless motors typically have Hall sensor commutation for speed and angle measurement. An electronic controller provides assistance as a function of the sensor inputs, the vehicle speed and the required force. The controllers generally allow input by means of potentiometer or Hall Effect twist grip (or thumb-operated lever throttle), closed-loop speed control for precise speed regulation, protection logic for over-voltage, over-current and thermal protection. Bikes with a pedal assist function typically have a disc on the crank shaft featuring a ring of magnets coupled with a Hall sensor giving rise to a series of pulses, the frequency of which is proportional to pedaling speed. The controller uses pulse width modulation to regulate the power to the motor. Sometimes support is provided for regenerative braking but infrequent braking and the low mass of bicycles limits recovered energy. An implementation is described in an application note for a 200 W, 24 V Brushless DC (BLDC) motor.[43]
The bicycle is extraordinarily efficient in both biological and mechanical terms. The bicycle is the most efficient human-powered means of transportation in terms of energy a person must expend to travel a given distance.[38] From a mechanical viewpoint, up to 99% of the energy delivered by the rider into the pedals is transmitted to the wheels, although the use of gearing mechanisms may reduce this by 10–15%.[39][40] In terms of the ratio of cargo weight a bicycle can carry to total weight, it is also an efficient means of cargo transportation.
The entire drive system is neatly incorporated into the bike's design for optimal weight distribution and the ultimate in sexy design, while users control torque and power output, which peaks at a surprisingly punchy 530W, via a cool Mission Control App that can also be programmed to a time or distance parameter to ensure there's enough power to get you home.
In general, more expensive bikes are better. However, this is just a trend. E.g. the "Kassensturz" Consumer program from our state TV found in a 2012 study confined to an engineering school, that "Supermarket" bikes, e.g. the 1400 CHF (1200 Euro) "Leopard" bike from COOP did very well. Evaluation is "good" (almost the same as the three times more expensive 25km/h Stromer). They also pointed out a very bad model from a discounter. In other words, you can find good cheap models, but read the tests first.
Included in this shipment are the much awaited 3540 motors with their slick "UFO" design. These are the replacements for the older square style "H" motors, you may have noticed that this change was implemented last year with the 3525 front and rear motors. As always, we have the motors customized with a 10K NTC thermistor for thermal rollback using the CA3.

Some argue, that an ebike should have some kind of front suspension, i.e. be able to cope with potholes at higher speed or off-road conditions. However, in countries with flat roads (e.g. Switzerland, Germany or Holland) you don't need that extra weight for extra price if you stay on roads and/or drive slowly in difficult terrain. Some makes (like the Stromer) let you choose.

However, laws and terminology are diverse. Some countries have national regulations but leave the legality of road use for states and provinces to decide. Municipal laws and restrictions add further complications. Systems of classification and nomenclature also vary. Jurisdictions may address "power-assisted bicycle" (Canada) or "power-assisted cycle" (United Kingdom) or "electric pedal-assisted cycles" (European Union) or simply "electric bicycles". Some classify pedelecs as distinct from other bikes using electric power. Thus, the same hardware may be subject to many different classifications and regulations.

In the early 1860s, Frenchmen Pierre Michaux and Pierre Lallement took bicycle design in a new direction by adding a mechanical crank drive with pedals on an enlarged front wheel (the velocipede). This was the first in mass production. Another French inventor named Douglas Grasso had a failed prototype of Pierre Lallement's bicycle several years earlier. Several inventions followed using rear-wheel drive, the best known being the rod-driven velocipede by Scotsman Thomas McCall in 1869. In that same year, bicycle wheels with wire spokes were patented by Eugène Meyer of Paris.[22] The French vélocipède, made of iron and wood, developed into the "penny-farthing" (historically known as an "ordinary bicycle", a retronym, since there was then no other kind).[23] It featured a tubular steel frame on which were mounted wire-spoked wheels with solid rubber tires. These bicycles were difficult to ride due to their high seat and poor weight distribution. In 1868 Rowley Turner, a sales agent of the Coventry Sewing Machine Company (which soon became the Coventry Machinists Company), brought a Michaux cycle to Coventry, England. His uncle, Josiah Turner, and business partner James Starley, used this as a basis for the 'Coventry Model' in what became Britain's first cycle factory.[24]
Hub motors are sold as either geared or direct drive: Geared hubs are preferred for hill climbing ability and zero drag when coasting, while DD hubs are more durable and suitable for high speed. Extreme hill climbing and high torque applications (fatbikes, hauling cargo, popping wheelies) usually requires a mid drive, which is covered in the motor section below. Ebike battery packs from the listed suppliers are generally compatible with kits from any supplier, at worst you may need a different connector, which can be easily replaced. You probably want a battery pack that is 36, 48, or 52 volts, depending on whether you prefer lower price and longer range or a higher topspeed. DIY lipo battery packs can be built cheaply but doing so can be a fire hazard so actual packs are recommended. All hub motors above 24 V should be installed with torque arms for safety.
Another style is the recumbent bicycle. These are inherently more aerodynamic than upright versions, as the rider may lean back onto a support and operate pedals that are on about the same level as the seat. The world's fastest bicycle is a recumbent bicycle but this type was banned from competition in 1934 by the Union Cycliste Internationale.[43]
I am very pleased with the quality and performance of this electric bike. I find that the twist grip throtle works better for me than the peddle assist low, medium and high settings. It is not necessary to change out of high gear to climb most hills while peddling with the throttle also providing power. The shocks work well on dirt paths and the seat is comfortable. This bike goes maximum speed up to 19 mph on flat ground. I have
There are dozens of good 25Km/h pedelecs. Our advice is to go the nearest good e-bike store and get it from there, because e-bikes may need good support. Only if you like servicing a bike yourself is buying from the Internet a good option. As of Spring 2013, a good benchmark to compare with is the Austrian KTM Amparo also called KTM Severo 8M or the German Kalkhoff Impuls or Agattu series. It has a reliable Panasonic middle motor and a good battery. If you want a more sexy design, try the SMART from the urban car maker of the same name.
Electric-assisted bicycles are treated as human-powered bicycles, while bicycles capable of propulsion by electric power alone face additional registration and regulatory requirements as mopeds. Requirements include electric power generation by a motor that cannot be easily modified, along with a power assist mechanism that operates safely and smoothly. In December 2008, The assist ratio was updated as follow:
First off we want to apologize for the longer than normal response time and email backlog as much of our team was busy both in the preparation and attendance at the Taipei Cycle Show this past week. We'll be working hard to catch up on that in the coming days and thank your patience and understanding. To all the dealers, vendors, manufacturers, component partners, and general industry friends we met at the show, what a great time and we look forward to exciting pursuits ahead. 
The drivetrain begins with pedals which rotate the cranks, which are held in axis by the bottom bracket. Most bicycles use a chain to transmit power to the rear wheel. A very small number of bicycles use a shaft drive to transmit power, or special belts. Hydraulic bicycle transmissions have been built, but they are currently inefficient and complex.