Step-throughs were popular partly for practical reasons and partly for social mores of the day. For most of the history of bicycles' popularity women have worn long skirts, and the lower frame accommodated these better than the top-tube. Furthermore, it was considered "unladylike" for women to open their legs to mount and dismount—in more conservative times women who rode bicycles at all were vilified as immoral or immodest. These practices were akin to the older practice of riding horse sidesaddle.[citation needed]
Electric bicycles have two main methods of operation: pedal-assist and/or throttle-control. As the name implies, pedal-assist “assists” your pedaling and requires some input. With this method, a torque sensor picks up movement or stress to determine the power requirements of the rider. Everything is automated so there’s nothing to think about, just jump on and start riding. Some bikes have multiple settings, while others have just one setting with the addition of a throttle control. Depending on the setting, pedal-assistance can help a little – or a lot. At lower settings, pedal-assist is barely noticeable but helps extend your range. At higher settings, the power is quite obvious and feels like a strong wind at your back with the motor doing most of the work while you pedal along.
Electric-assisted bicycles, also referred to as "e-bikes," are a subset of bicycles that are equipped with a small attached motor. To be classified as an "electric-assisted bicycle" in Minnesota, the bicycle must have a saddle and operable pedals, two or three wheels, and an electric motor of up to 1,000 watts, as well as meet certain federal motor vehicle safety standards. The motor must disengage during braking and have a maximum speed of 20 miles per hour (whether assisted by human power or not). Minn. Stat. §169.011, subd. 27.
(2) BICYCLE.--Every vehicle propelled solely by human power, and every motorized bicycle propelled by a combination of human power and an electric helper motor capable of propelling the vehicle at a speed of not more than 20 miles per hour on level ground upon which any person may ride, having two tandem wheels, and including any device generally recognized as a bicycle though equipped with two front or two rear wheels. The term does not include such a vehicle with a seat height of no more than 25 inches from the ground when the seat is adjusted to its highest position or a scooter or similar device. No person under the age of 16 may operate or ride upon a motorized bicycle.
8. Rights Granted by you: By entering this content you understand that Electric Bike Technologies INC., anyone acting on behalf of Electric Bike Technologies INC., or its respective licensees, successors and assigns will have the right, where permitted by law, without any further notice, review or consent to print, publish, broadcast, distribute, and use, worldwide in any media now known or hereafter in perpetuity and throughout the World, your entry, including, without limitation, the entry and winner's name, portrait, picture, voice, likeness, image or statements about the Sweepstakes, and biographical information as news, publicity or information and for trade, advertising, public relations and promotional purposes without any further compensation.
We take a look at the phenomenon sweeping the trails across Europe – Electric Mountain Bikes. After extensive research and a visit to Eurobike, our team hand-picked what we feel to be the best electric mountain bikes in 2018 using Yamaha, Shimano and Bosch eBike systems. Following the visit to Eurobike, it was clear that … Continue reading Best Electric Mountain Bikes 2018 – The Fully Charged Picks
The body is made from light and durable aluminum. The handlebar comes with simple controls to let you accelerate, brake, monitor battery life, operate headlights and of course…sound the horn. There’s even an USB point that will let you charge your iPhone or Android on the go. The bike can reach a top speed of 10mph. Feel the wind in your hair as you zoom up and down hills and past all that city traffic…
In some countries mixed systems, i.e. pedaling and/or using a throttle is legal. In EU countries and Switzerland this is not the case. I.e. you can buy an electric scooter, but this is not considered to be an e-bike in the moped / light scooter category. That kind of hack is probably more difficult, unless the original design has been modified to fit with (s)Pedelec specs. E.g. The Ezee models are of that kind and modifications to revert to the original does not seem to be too difficult...
Electric-assisted bicycles are treated as human-powered bicycles, while bicycles capable of propulsion by electric power alone face additional registration and regulatory requirements as mopeds. Requirements include electric power generation by a motor that cannot be easily modified, along with a power assist mechanism that operates safely and smoothly. In December 2008, The assist ratio was updated as follow:
On February 4, 2014, SB997 was introduced by Senator Matt Smith, which seeks to amend PA Vehicle Code to include "Pedalcycle with Electric Assist". In a memo addressed to all senate members, Smith said the definition shall include "bicycles equipped with an electric motor not exceeding 750 watts, weighing not more than 100 pounds, are capable of a maximum speed of not more than 20 mph, and have operable pedals."[128][129]
All classes of electric-assisted bicycles may be operated on a fully controlled limited access highway. Class 1 and 2 electric bicycles can be used on sidewalks, but Class 3 bicycles "may not be used on a sidewalk unless there is no alternative to travel over a sidewalk as part of a bicycle or pedestrian path."[143] Generally a person may not operate an electric-assisted bicycle on a trail that is designated as non-motorized and that has a natural surface, unless otherwise authorized.
Another type of electric assist motor, often referred to as the mid-drive system, is increasing in popularity. With this system, the electric motor is not built into the wheel but is usually mounted near (often under) the bottom bracket shell. In more typical configurations, a cog or wheel on the motor drives a belt or chain that engages with a pulley or sprocket fixed to one of the arms of the bicycle's crankset. Thus the propulsion is provided at the pedals rather than at the wheel, being eventually applied to the wheel via the bicycle's standard drive train.
Many newer or smaller companies only design and market their products; the actual production is done by Asian companies. For example, some 60% of the world's bicycles are now being made in China. Despite this shift in production, as nations such as China and India become more wealthy, their own use of bicycles has declined due to the increasing affordability of cars and motorcycles.[102] One of the major reasons for the proliferation of Chinese-made bicycles in foreign markets is the lower cost of labor in China.[103]
This is list of the best performing, best value electric bikes for 2018 / 2019. For each category I list two models, the first recommendation is based on performance and the second is based on affordability. As you explore the list and get to know EBR, check out the ebike community forum for more personalized feedback. Share your height, weight, budget and intended use (along with bikes you like) to get advice from actual owners and moderators.
The recommendation depends a lot on what you plan to use the bike for and how you plan to ride. That said, I would recommend at least a 750 (if not 1,000) watt motor, and, if you want reasonable range, 48 or 52v cells with a minimum rating of 19ah. For shorter rides, you can use a smaller battery. Multiply battery voltage by amp hour rating to get battery watt hours. Divide the watt hours by the motors power rating to get a general idea of how many hours of heavy use you might get. I’d also recommend a mid drive as opposed to a hub drive, or to find a hub drive wheel rated to take your and the bicycle's combined weight.
Nevada Electric Bicycle (NRS 482.0287) Bicycle 20 (motor only on the flat with 170LB rider, undefined if pedal assist is allowed to go faster) 750W (it is undefined as to whether this is input or output power, but in the USA, motors are rated on output power at the shaft) No none (use caution here because of "reckless endangerment" laws) no (not a "motor vehicle")
This page and all motor documentation pages are created and maintained by Lunacycle Support for purposes of referrals, references and education, and are the culmination of many years involvement in the ebike scene. While we would love if you bought from us there are a lot of good companies in the documentation and we hope it helps you to make the most informed choices for your build.
As long as you can do without some of the perks that pricier models offer—like a detailed display unit, integrated lights, and a torque-sensor motor—the August Live! LS is a solid, stable, comfortable, and really freakin’ cute (have you see those polka-dot fenders?) e-bike. Its 8-speed twist shifter, chopper-style handlebar, Touch Down Geometry (for a more laid-back ride), and three levels of assist keep this bike within the realm of “cruiser.” But with a 250-watt Bafang rear-hub motor, a top pedal-assisted speed of 20 mph, and reliable disc brakes, the August is no joke. It’ll get you to the top of relatively steep climbs without forcing you out of the saddle, and it feels super stable on the way back down. It has a battery range of 20 miles, but that’s enough to take it where it’s happiest: tootling along at the beach, around town, and through the park.

The environmental effects involved in recharging the batteries can of course be reduced. The small size of the battery pack on an e-bike, relative to the larger pack used in an electric car, makes them very good candidates for charging via solar power or other renewable energy resources. Sanyo capitalized on this benefit when it set up "solar parking lots", in which e-bike riders can charge their vehicles while parked under photovoltaic panels.[66]

A human traveling on a bicycle at low to medium speeds of around 16–24 km/h (10–15 mph) uses only the power required to walk. Air drag, which is proportional to the square of speed, requires dramatically higher power outputs as speeds increase. If the rider is sitting upright, the rider's body creates about 75% of the total drag of the bicycle/rider combination. Drag can be reduced by seating the rider in a more aerodynamically streamlined position. Drag can also be reduced by covering the bicycle with an aerodynamic fairing. The fastest recorded unpaced speed on a flat surface is 144.18 km/h (89.59 mph)[41]


DON'T BUY THIS BIKE!!!!! Worst customer service ever!!! I bought this bike for my 18 year old son to commute to school. It worked well for the first 2 months but the battery is cheap and stated to wear out. I tried going on the website, but they battery shows as out of stock, and has been for 3 months now. I left 5 emails with customer service, never got a reply. Also there is no number listed on their website to even speak to a real person. Now I have a worthless 5 month old bike..... horrible this company should be ashamed.
As we already noted, roadways in many countries aren’t the ideal places for bicycles, as transportation engineers spent the last century or so designing them only to accommodate cars. The average bike rider moves at a pace that’s fast enough to surprise drivers, but slow enough to make it difficult for them to avoid dangerous situations. An electric bike’s increased speed helps to even the playing field, giving you the opportunity to quickly avoid an accident.
There's much less of a sensation of the Electrified S2 'fighting back' once you hit 15.5mph, as well. That's helped by the automatic 2-speed gear box, although this does take some getting used to. Because its cogs are very different sizes you can end up with all sorts of cadence problems as it auto-shifts from high back to low. With practice you can avoid this, or of course you could in theory fit a second cog that's closer in size to the first.

Several bills have been sponsored to legalize electric bicycles for use on NYS roads, and several have overwhelmingly passed at the committee level, but none of these initiatives has been able to be heard and then passed in the New York State Senate, until 2015. The latest bill S3997, "An act to amend the vehicle and traffic law, in relation to the definition of electric assisted bicycle. Clarifying the vehicle and traffic law to define electric assisted bicycles; establish that electric assisted bicycles, as defined, are bicycles, not motor vehicles; and establish safety and operational criteria for their use." has passed in the Senate for the first time ever in 2015.[116] The related Assembly bill A233 was not brought to a vote in the assembly even though it had passed with little issue in prior years.[117]

Again, these are base level components here. The Shimano/TX55 gearing is fine for this application level but I have lost my chain a few times in a few weeks. The frame is surprisingly solid aluminum alloy which feels stiffer and lighter than last year’s Ancheer. The supplied front 10W light is very bright, however the back light is charged via USB and has a push button rather than being wired into the controller. The disc brakes are the same no-name brand as the Ancheer but appear to be a size bigger. The fork, while not amazing, is a big improvement in stiffness and give over the Ancheer’s, which scared me a bit.


Some argue, that an ebike should have some kind of front suspension, i.e. be able to cope with potholes at higher speed or off-road conditions. However, in countries with flat roads (e.g. Switzerland, Germany or Holland) you don't need that extra weight for extra price if you stay on roads and/or drive slowly in difficult terrain. Some makes (like the Stromer) let you choose.

DIY enthusiasts, with tens of thousands of converted bikes using throttle-only, 20+ mph kits, are now officially labeled Moped class. While these bikes handle and pedal-ride just as safely as the class 3 speed pedelecs in many cases, our DIY counterparts will be officially kicked out and left on their own for advocacy and legal acceptance in California. This is a big deal, without a class sticker, any DIY electric bike conversion kit is considered a Moped and not a bicycle.
The environmental credentials of e-bikes, and electric / human powered hybrids generally, have led some municipal authorities to use them, such as Little Rock, Arkansas with their Wavecrest electric power-assisted bicycles or Cloverdale, California police with Zap e-bikes. China’s e-bike manufacturers, such as Xinri, are now partnering with universities in a bid to improve their technology in line with international environmental standards, backed by the Chinese government who is keen to improve the export potential of the Chinese manufactured e-bikes.[67]
Legislative changes in 2012 significantly altered the classification and regulatory structure for e-bikes. The general effect was to establish electric-assisted bicycles as a subset of bicycles and regulate e-bikes in roughly the same manner as bicycles instead of other motorized devices with two (or three) wheels. Laws 2012, ch. 287, art. 3, §§ 15-17, 21, 23-26, 30, 32-33, and 41. The 2012 Legislature also modified and clarified regulation of e-bikes on bike paths and trails. Laws 2012, ch. 287, art. 4, §§ 1-4, 20.
Legislative changes in 2012 significantly altered the classification and regulatory structure for e-bikes. The general effect was to establish electric-assisted bicycles as a subset of bicycles and regulate e-bikes in roughly the same manner as bicycles instead of other motorized devices with two (or three) wheels. Laws 2012, ch. 287, art. 3, §§ 15-17, 21, 23-26, 30, 32-33, and 41. The 2012 Legislature also modified and clarified regulation of e-bikes on bike paths and trails. Laws 2012, ch. 287, art. 4, §§ 1-4, 20.
This page and all motor documentation pages are created and maintained by Lunacycle Support for purposes of referrals, references and education, and are the culmination of many years involvement in the ebike scene. While we would love if you bought from us there are a lot of good companies in the documentation and we hope it helps you to make the most informed choices for your build.
Some electric bikes claim to use a neat trick called regenerative braking. If you start pedaling the bicycle or going downhill, the spinning wheels turn the electric motor in the hub in reverse and start charging up the batteries. In practice, regenerative braking is nowhere near as useful on an electric bicycle as it is on an electric train or car. An electric bike has much less mass and velocity than either a train or car, so it never gains (or loses) anything like as much kinetic energy when it starts and stops. You'd have to go down an awful lot of hills to charge up the batteries completely and that's usually not practical. And what's the point in pedaling the wheels simply to charge the battery? You might as well have bought an ordinary bicycle to start with!
Motor-driven cycles may be operated on the roadway without registration, but the operator must have a driver's license.[85] The cycle may not be operated on any sidewalk, limited access highway or turnpike. If the maximum speed of the cycle is less than the speed limit of the road, the cycle must operate in the right hand lane available for traffic or upon a usable shoulder on the right side of the road unless the operator is making a left turn.

This is a cool eBike fits in your car's trunk or back seat! It's well made. And it only has one rear disc brake, you dont really need the front brake. It's simple to operate and fun to use - just put one foot on one foot attachment while turning the throttle slightly, then as soon as you start to move add the other foot...and let the joy ride begin!
If you have dynamo-powered bicycle lights, you already own an electric-powered bicycle! Consider: as you pump your legs up and down on the pedals, you make the wheels rotate. A small dynamo (generator) mounted on the rear wheel produces a tiny current of electricity that keeps your back safety lamp lit in the dark. Now suppose you could run this process backward. What if you removed the lamp and replaced it with a large battery. The battery would kick out a steady electric current, driving the dynamo in reverse so that it spun around like an electric motor. As the dynamo/motor turned, it would rotate the tire and make the bike go along without any help from your pedaling. Hey presto: an electric bike! It may sound a bit far-fetched, but this is more or less exactly how electric bikes work.
9. Terms: Electric Bike Technologies INC. reserves the right, in its sole discretion to cancel, terminate, modify or suspend the Sweepstakes should (in its sole discretion) a virus, bugs, non-authorized human intervention, fraud or other causes beyond its control corrupt or affect the administration, security, fairness or proper conduct of the Sweepstakes. In such case, Electric Bike Technologies INC. may select the recipients from all eligible entries received prior to and/or after (if appropriate) the action taken by Electric Bike Technologies INC.. Electric Bike Technologies INC. reserves the right at its sole discretion to disqualify any individual who tampers or attempts to tamper with the entry process or the operation of the Sweepstakes or website or violates these Terms & Conditions.
While we're still fairly new to the solar ebike game, Mark is among the (suprisingly numerous) Grin customers who've been thinking about and experimenting with solar bikes for many years. After he shared pictures of his latest project and mentioned his round the world touring ambitions, we thought we had to do a small feature on this guy. A quick last minute trip to Maker Faire was arranged to meet up, and here we present, Mark Havran:

8. Rights Granted by you: By entering this content you understand that Electric Bike Technologies INC., anyone acting on behalf of Electric Bike Technologies INC., or its respective licensees, successors and assigns will have the right, where permitted by law, without any further notice, review or consent to print, publish, broadcast, distribute, and use, worldwide in any media now known or hereafter in perpetuity and throughout the World, your entry, including, without limitation, the entry and winner's name, portrait, picture, voice, likeness, image or statements about the Sweepstakes, and biographical information as news, publicity or information and for trade, advertising, public relations and promotional purposes without any further compensation.

First off we want to apologize for the longer than normal response time and email backlog as much of our team was busy both in the preparation and attendance at the Taipei Cycle Show this past week. We'll be working hard to catch up on that in the coming days and thank your patience and understanding. To all the dealers, vendors, manufacturers, component partners, and general industry friends we met at the show, what a great time and we look forward to exciting pursuits ahead. 
It should be noted that the definition as written does not define the power of the motor in Watts as is conventionally done for electric bicycles but rather in brake horsepower. Thus for an electric bicycle, motor kit, or electric bicycle motor that is not rated by the manufacture in brake horsepower but rather in Watts a conversion must be made in the units a conversion which is not given in the code of the law and thus the court will have to consider a factor of conversion that is not directly encoded in the law. Industry standard conversion for Watts to horsepower for electric motors is 1 horsepower = 746 watts.[105] Acceptance of that conversion factor from industry, however, as interpretation of the law is subject to the process of the courts since it is not defined specifically in the law.
I eventually got used to it over time, but at first having both kids behind me made the bike feel like it would sway to or fro perilously. I think it was just too much weight to navigate safely, and would be fine with younger kids that didn’t come close to the 120-pound weight limit for the rear cargo area. Overall I’m still a bit partial to a box-style bike if I’m hauling multiple kids and want to be able to see what they’re doing.

If you're taking your bike inside, consider one that folds up. The Cyclotricity Wallet has a motor in the front wheel, which takes you up to speed either by assisting your pedalling, or you can sit back and use the throttle by itself. Its folding design makes it slightly easier to get in and out of a building, but its hefty weight means you still won't find it easy to carry onto public transport.
The are no ADRs applicable to AA or AB category vehicles. There are ADRs for lighting, braking, noise, controls and dimensions for LA category vehicles, mostly referencing the equivalent UN ECE Regulations. An approval is required to supply to the market any road vehicle to which ADRs apply and an import approval is required to import any road vehicle into Australia[4].
Under the statute, mopeds must be registered. To be registered under Hawaii law a moped must bear a certification label from the manufacturer stating that it complies with federal motor vehicle safety standards (FMVSS). A moped must also possess the following equipment approved by the D.O.T. under Chapter 91: approved braking, fuel, and exhaust system components; approved steering system and handlebars; wheel rims; fenders; a guard or protective covering for drive belts, chains and rotating components; seat or saddle; lamps and reflectors; equipment controls; speedometer; retracting support stand; horn; and identification markings.
In addition, we have a new lineup of torque sensors from NCTE to replace the long out-of-stock THUN devices. This restores the option for a true transducer that measures the actual spindle torsion. They provide an accurate human watts readout, and unlike other sensors they can be used in mid-drive setups where the motor is driving the right side chain.
The rest of the bike is equally impressive. Integrated lights in the front and the rear run directly off the main battery, so you’re never replacing coin cells or AAA batteries. And the disc brakes give you plenty of stopping power. The 36-volt battery attaches to the down tube and is designed to be easily removed for recharging. A key-lock at the top of the mount ensures that no one can steal your battery if your bike is left in a public place. And a built-in alarm system, activated with a car-like key fob, is ear-splitting enough to keep thieves away altogether. (Miller promises the alarm’s sensitivity is tuned so it shouldn’t go off if the bike is jostled at a public bike rack, but I didn’t have the bike long enough to test this out.)
Today I’m looking at the Rattan Challenger 350W ebike. It can be found for under $680 at Amazon (after Electrek coupon code 5AIDO2GB) shipped and includes free assembly at a local bike shop. I assembled mine at home however in about 15 minutes with the graciously supplied in box hex tool and wrenches. It is pretty straight forward – the hardest part was bolting the front light on.
As of May 19, 2009, Nevada amended its state transportation laws to explicitly permit electric bicycles to use any "trail or pedestrian walkway" intended for use with bicycles and constructed with federal funding, and otherwise generally permits electric bicycles to be operated in cases where a regular bicycle could be. An electric bicycle is defined as a two- or three-wheeled vehicle with fully operable pedals with an electric motor producing up to 1 gross brake horsepower and up to 750 watts final output, and with a maximum speed of up to 20 miles per hour on flat ground with a 170-pound rider when powered only by that engine.[106]
As you evaluate the different folding electric bikes on the market, you’ll notice that there are a lot of inherent similarities from one brand to the next, even though the look of each brand’s attempt has some unique aspects to it. No matter how the bike looks, each of your options will have a motor that’s powered by a battery, a hinge that allows the bike to fold roughy in half, and a series of other features that you would regularly find on a normal bicycle, such as pedals, brakes, handlebars, etc.
The legal definition/description of an electric bicycle is most closely described in the code as a "motorized scooter" in that it is powered by an electric motor and/or human power [45]. It may be also be described as a "Motorized bicycle". However, that description does not include electric powered motor specifically. And it appears that the legal definition "Motorized Bicycle" and "Motorized Scooter" are in conflict. Motorized bicycle is a pedal bicycle which has a helper motor, or a non-pedal bicycle which has a motor, with a cylinder capacity not exceeding fifty cubic centimeters, an automatic transmission, and which is capable of a maximum speed of no more than thirty miles per hour. A motorized bicycle shall not be operated upon any way, as defined in section one within the commonwealth by any person under sixteen years of age, nor at a speed in excess of twenty-five miles per hour. A motorized bicycle shall not be operated on any way by any person not possessing a valid driver’s license or learner’s permit. Every person operating a motorized bicycle upon a way shall have the right to use all public ways in the commonwealth except limited access or express state highways where signs specifically prohibiting bicycles have been posted, and shall be subject to the traffic laws and regulations of the commonwealth and the regulations contained in this section, except that the motorized bicycle operator may keep to the right when passing a motor vehicle which is moving in the travel lane of the way, and the motorized bicycle operator shall signal by either hand his intention to stop or turn. Motorized bicycles may be operated on bicycle lanes adjacent to the various ways, but shall be excluded from off-street recreational bicycle paths. Every person operating a motorized bicycle or riding as a passenger on a motorized bicycle shall wear protective headgear conforming with such minimum standards of construction and performance as the registrar may prescribe, and no person operating a motorized bicycle shall permit any other person to ride a passenger on such motorized bicycle unless such passenger is wearing such protective headgear.

If you're more concerned with conquering the countryside than the commute, Cyclotricity's Stealth is the one for you. It's a full-size mountain bike, with aggressive tyres and suspension on the front forks to absorb the rocks and bumps on the trails. It's comfortable to ride, and its motor can either give you assistance while you ride, or you can just hit the throttle to rocket over hills with no effort on your part.
The Christmas day is coming soon, since I receive the bike, it's about a week, and I am satisfied with it! just as advertised, very powerful and good design. the most important point is that once the battery is FULL CHARGE, how far it can reach up to. I have a funny test, in the normal road(not in the dramatic slope or uphill), it can goes almost 44 miles. That is what I give 5 star for this bike! very powerful with reasonable price!
Front-Mounted Hub Motor can be found on pre-built bikes or on custom conversions. Mounted to the front wheel, this is the easiest configuration to setup if you’re converting a standard bicycle since there’s no derailleur or chain to worry about. And since most e-bike conversions include batteries mounted to the rear rack, using a front hub motor helps equalize the weight of the bike and makes it easier to handle. But there’s a small risk the motor could cause the front forks to brake. That’s why it’s vital you only use a front hub motor on a steel fork. For pre-built bikes, this shouldn’t be an issue since the motors are usually lower-powered on steel forks.

Not all e-bikes take the form of conventional push-bikes with an incorporated motor, such as the Cytronex bicycles which use a small battery disguised as a water bottle.[44][45] Some are designed to take the appearance of low capacity motorcycles, but smaller in size and consisting of an electric motor rather than a petrol engine. For example, the Sakura e-bike incorporates a 200 W motor found on standard e-bikes, but also includes plastic cladding, front and rear lights, and a speedometer. It is styled as a modern moped, and is often mistaken for one.[citation needed]
There's much less of a sensation of the Electrified S2 'fighting back' once you hit 15.5mph, as well. That's helped by the automatic 2-speed gear box, although this does take some getting used to. Because its cogs are very different sizes you can end up with all sorts of cadence problems as it auto-shifts from high back to low. With practice you can avoid this, or of course you could in theory fit a second cog that's closer in size to the first.
×