Electric-assisted bicycle operators must follow the same traffic laws as operators of motor vehicles (except those that by their nature would not be relevant). The bicycles may be operated two abreast. Operators must generally ride as close as is practical to the right-hand side of the road (exceptions include when overtaking another vehicle, preparing for a left turn, and to avoid unsafe conditions). The bicycle must be ridden within a single lane. Travel on the shoulder of a road must be in the same direction as the direction of adjacent traffic.
The newest entrant in this lower price category is Wing Bikes, a New York City-based company that launched in 2018. Wing wants to be the affordable e-bike for city residents who are sick of shady ride-hailing services and stalled subways. And if you don’t live in a city, that’s fine too: Wing’s e-bikes could be a realistic alternative to owning a car.
This is one of the most incredible eBikes on the market today! The Riese and Muller SuperCharger Rohloff GX is one of our most popular models and we know they are being put through thousands of miles across the Southeast. From the coastal areas to the Appalachian mountains, we have customers buying and riding these highly engineered eBikes. These eBikes …
Besides voltage, batteries are rated by amp hours (AH). Although voltage seems to get the most attention, the amp hour rating of the battery is just as important. It is the measure of a battery’s capacity and provides a good indication of the range you can expect from an electric bike. Although lots of factors come into play in determining range (ie: rider weight, terrain, input, efficiency, etc.), a good rule of thumb is range is equal to AH. So under normal conditions, an average rider can expect 10 miles out of a 10AH battery (with no pedaling). With rider input, this number can be dramatically increased, so most 10AH batteries are rated “up to 20 miles” by the manufacturer which assumes pedaling. On pedal-assist bikes (which require pedaling), the range ratings are much higher because the rider is constantly assisting the motor and reducing the current draw.
Another type of electric assist motor, often referred to as the mid-drive system, is increasing in popularity. With this system, the electric motor is not built into the wheel but is usually mounted near (often under) the bottom bracket shell. In more typical configurations, a cog or wheel on the motor drives a belt or chain that engages with a pulley or sprocket fixed to one of the arms of the bicycle's crankset. Thus the propulsion is provided at the pedals rather than at the wheel, being eventually applied to the wheel via the bicycle's standard drive train.
With hand-operated brakes, force is applied to brake levers mounted on the handlebars and transmitted via Bowden cables or hydraulic lines to the friction pads, which apply pressure to the braking surface, causing friction which slows the bicycle down. A rear hub brake may be either hand-operated or pedal-actuated, as in the back pedal coaster brakes which were popular in North America until the 1960s.
Geared Hub Motors – Most pre-built e-bikes use brushless geared hub motors. These motors have internal planetary gears that help transfer power from the motor to the wheel. Because of the internal gearing, these motors provide excellent torque but are limited in top speed. On the plus side, the improved torque means better take-off power and hill climbing ability. Plus, less wattage is required to get the motor turning and they’re typically small and lightweight. On pre-built e-bikes, these motors range from 200w-500w and go up to 20mph. But some aftermarket kits can be as powerful as 1000w, with increased top speeds and huge amounts of torque (ideal for extremely hilly terrain). Besides lower top speeds, these motors tend to be expensive and it’s possible the gears will eventually wear out and need to be replaced (this is highly unlikely, they las quite a long time). Good examples are Ancheer bikes.
Electric bicycles have two main methods of operation: pedal-assist and/or throttle-control. As the name implies, pedal-assist “assists” your pedaling and requires some input. With this method, a torque sensor picks up movement or stress to determine the power requirements of the rider. Everything is automated so there’s nothing to think about, just jump on and start riding. Some bikes have multiple settings, while others have just one setting with the addition of a throttle control. Depending on the setting, pedal-assistance can help a little – or a lot. At lower settings, pedal-assist is barely noticeable but helps extend your range. At higher settings, the power is quite obvious and feels like a strong wind at your back with the motor doing most of the work while you pedal along.
You can learn more about the development and axle testing process on this endless-sphere thread. Our ambition is to make this splined axle design into a new standard that we deploy across our entire higher power motor lines to replace axle flats. If you're as excited as us and want to jump right into ordering, we have the first production shipment on hand available in bare motors and complete kits.
I purchased version 2.0 of this device and the manufacturer has been listening to comments from users and making running changes such as the three speeds and the rear suspension. I am an XL size user (6'2", 230lbs) and recently returned from a 26 day cruise around Europe. I rode this little scooter on cobblestones, miles and miles through the Vatican, inside ancient cities and all over the streets of San Juan upon our return stateside. There was only one time it was less than ideal and that was going uphill, on slick tile that was wet from a drizzle. It still make it, just had to lean way forward to get weight on the front wheel. 
×