For a more stylish ride, cast your eyes over the Coboc Rome. It's a full-size bike, with gorgeous stylings, and large wheels that let you pick up plenty of speed on the road. It has a fuss-free approach too, with its automatic motor assistance -- all you need to do is get on and ride. It's very much like any fixed gear bike you'll see on the streets, but with the additional motor, it's less effort to get about.
E-bike usage worldwide has experienced rapid growth since 1998. In 2016 there were 210 million electric bikes worldwide used daily.[33] It is estimated that there were roughly 120 million e-bikes in China in early 2010, and sales are expanding rapidly in India, the United States of America, Germany, the Netherlands,[2] and Switzerland.[34] A total of 700,000 e-bikes were sold in Europe in 2010, up from 200,000 in 2007 and 500,000 units in 2009.[35]
In some countries mixed systems, i.e. pedaling and/or using a throttle is legal. In EU countries and Switzerland this is not the case. I.e. you can buy an electric scooter, but this is not considered to be an e-bike in the moped / light scooter category. That kind of hack is probably more difficult, unless the original design has been modified to fit with (s)Pedelec specs. E.g. The Ezee models are of that kind and modifications to revert to the original does not seem to be too difficult...
Electric bicycle fits under the definition of "moped" under Kentucky law. You don't need tag or insurance, but you need a driver's license. "Moped" means either a motorized bicycle whose frame design may include one (1) or more horizontal crossbars supporting a fuel tank so long as it also has pedals, or a motorized bicycle with a step-through type frame which may or may not have pedals rated no more than two (2) brake horsepower, a cylinder capacity not exceeding fifty (50) cubic centimeters, an automatic transmission not requiring clutching or shifting by the operator after the drive system is engaged, and capable of a maximum speed of not more than thirty (30) miles per hour[94][95] Helmets are required.
However, each country is free to allow faster s-pedelecs if they go through collective or individual type approval. Typically, an S-Pedelec can be associated with "mofas" or "mopeds" or "light scooters". Germany has such a solution: S-pedelecs have max. 500W motors, max 45km/h, max 300% support, can drive up to 20Km/h without pedalling, plus other constraints regarding security, and are associated with Mopeds. In the City you can't use bicycles paths, but you can in the country side.
Several bills have been sponsored to legalize electric bicycles for use on NYS roads, and several have overwhelmingly passed at the committee level, but none of these initiatives has been able to be heard and then passed in the New York State Senate, until 2015. The latest bill S3997, "An act to amend the vehicle and traffic law, in relation to the definition of electric assisted bicycle. Clarifying the vehicle and traffic law to define electric assisted bicycles; establish that electric assisted bicycles, as defined, are bicycles, not motor vehicles; and establish safety and operational criteria for their use." has passed in the Senate for the first time ever in 2015.[116] The related Assembly bill A233 was not brought to a vote in the assembly even though it had passed with little issue in prior years.[117]
But the whole is also influenced by the sensory systems which are very different from model to model. E.g. A typical 2013 Panasonic system requires pedalling for optimal support (55/minute?) and has both a pedalling frequency and a speed sensor. You don't get much assistance if you pedal very slowly or very fast. Typically, a rear motor has a force sensor, i.e. you get lots of support fast when you start pedalling in a low gear, i.e. it will "feel" your need for assistance.
eBikes are a key part of solution to reduce carbon emissions globally. The Zero-emission part of the eBike discussion is based on re-charging the battery on a daily basis from a Sustainable Electrical Source such as solar, wind, hydro, geo thermal, etc.  The fact is today part of the eBike Battery charge is coming from Power Plants that are running …

Use of and/or registration on any portion of this site constitutes acceptance of our User Agreement (updated 5/25/18) and Privacy Policy and Cookie Statement (updated 5/25/18). Your California Privacy Rights. The material on this site may not be reproduced, distributed, transmitted, cached or otherwise used, except with the prior written permission of Condé Nast. Ad Choices.


There are specialized bicycle tools for use both in the shop and on the road. Many cyclists carry tool kits. These may include a tire patch kit (which, in turn, may contain any combination of a hand pump or CO2 Pump, tire levers, spare tubes, self-adhesive patches, or tube-patching material, an adhesive, a piece of sandpaper or a metal grater (for roughing the tube surface to be patched), Special, thin wrenches are often required for maintaining various screw fastened parts, specifically, the frequently lubricated ball-bearing "cones".[57][58] and sometimes even a block of French chalk.), wrenches, hex keys, screwdrivers, and a chain tool. There are also cycling specific multi-tools that combine many of these implements into a single compact device. More specialized bicycle components may require more complex tools, including proprietary tools specific for a given manufacturer.


In a friction drive motor, a small, solid wheel rotates against the side of the tire in order to drive it. The first motorcycles used the same concept, with a motor mounted above the front wheel. The problem is that the drive rubs at the side of the tire. It's inefficient, and it quickly wears the sidewall away. Tires need to be replaced every couple hundred miles. For this reason, you'll seldom see electric bikes with this type of drive anymore.


Under the doctrine of One Country, Two Systems, Hong Kong has independent traffic law from mainland China. Electric bike are considered as motorcycles in Hong Kong, and therefore needs type approval from the Transport Department as other automobiles. All electric bike availble in Hong Kong fail to meet the type approval requirement, and Transport Department has never granted any type approval for electric bike, making all electric bike effectively illegal in Hong Kong. Even if they got type approved, the driver would need a motorcycle driving license to ride[14]. As a side note, Hong Kong doesn't have a moped vehicle class (and therefore moped driving license), and mopeds are consided as motorcycles too.
I did my commute a few times with the Rattan and while I would never give up my “bike store” e-bike for this, it was a worthy substitute. It never gave out on the big hills, nor did I have to brake because I felt the bike was falling apart. The frame is a little small for 6-foot me but it only comes in one size. I really miss the low rolling drag of having road tires however and this is something that both Rattan and Ancheer could improve upon. I don’t think many people are seriously off-roading with these bikes. Put some Schwalbe Big Bens on there!
One of the items we demonstrated at the show is the new GMAC motor series. This is a powerful clutchless geared hub motor developed over the past 2 years in partnership with MAC motors, using a custom axle with an integrated splined torque arm. Imagine a MAC motor with perfect frame fit for modern bicycles, zero torque transmission on the dropouts, and phenomenal regenerative braking control.
If you are an experienced rider this is actually annoying as hell. Personally, I tend to leave whatever I'm riding in a high gear all the time, because my body is like a powerful machine, and I found the way it slowed my escape from the lights quite disconcerting. For beginners, it could be useful, but it's worth remembering that the whole point of e-bikes is that the motor helps you along anyway, so I do really question the usefulness of this.
In Australia the e-bike is defined by the Australian Vehicle Standards as a bicycle that has an auxiliary motor with a maximum power output not exceeding 200 W without consideration for speed limits or pedal sensors.[1] Each state is responsible for deciding how to treat such a vehicle and currently all states agree that such a vehicle does not require licensing or registration. Various groups are lobbying for an increase in this low limit to encourage more widespread use of e-bikes to assist in mobility, health benefits and to reduce congestion, pollution and road danger. Some states have their own rules such as no riding under electric power on bike paths and through built up areas so riders should view the state laws regarding their use. There is no licence and no registration required for e-bike usage.
The safety bicycle gave women unprecedented mobility, contributing to their emancipation in Western nations. As bicycles became safer and cheaper, more women had access to the personal freedom that bicycles embodied, and so the bicycle came to symbolize the New Woman of the late 19th century, especially in Britain and the United States.[8][73] The bicycle craze in the 1890s also led to a movement for so-called rational dress, which helped liberate women from corsets and ankle-length skirts and other restrictive garments, substituting the then-shocking bloomers.[8]
In Australia the e-bike is defined by the Australian Vehicle Standards as a bicycle that has an auxiliary motor with a maximum power output not exceeding 200 W without consideration for speed limits or pedal sensors.[1] Each state is responsible for deciding how to treat such a vehicle and currently all states agree that such a vehicle does not require licensing or registration. Various groups are lobbying for an increase in this low limit to encourage more widespread use of e-bikes to assist in mobility, health benefits and to reduce congestion, pollution and road danger. Some states have their own rules such as no riding under electric power on bike paths and through built up areas so riders should view the state laws regarding their use. There is no licence and no registration required for e-bike usage.
The Registrar will permit an electric motor driven cycle to be registered if it meets Canada Motor Vehicle Safety Standards (CMVSS) as a Limited Speed Motorcycle, or Scooter as is done with gas powered motor driven cycles. If the vehicle was manufactured after 1988 it will bear a compliance label stating that it meets these standards. The operator will be subject to all the requirements placed on operators of motor driven cycles.

Class 1 makes great inroads to establish set boundaries for off road/natural surface trail access for eMountain bikes. There is fierce resistance from some mountain biking purists to allow ebikes on trails. BPSA and IMBA have done good work to justify the impact of class 1 ebikes on natural surface trails, and eliminate the wear-n-tear argument, though IMBA members are not 100% on board.
This upgraded model is the best scooter of this type that is currently available on the market. I have permanent mobility issues because of my left leg that do not allow me to walk any long distances. This scooter is allowing me to finally get out of the house to see and do some things again, even if that is just cruising around the neighborhood, but my main reason for purchasing it was so that I can go watch my granddaughters playing softball this spring, they are quite good.

In 5 years of working as a bike messenger in Minneapolis, I've ridden all kinds of bikes, in all kinds of weather. I've ridden walmart mountain bikes, 80's classic steel road bikes, kitted out Treks, pretty much everything EXCEPT for fat tire bikes. Such wide tires always seemed... too much. No need for a bike that only makes itself worthwhile maybe two months out of the year, I thought.
Maybe the most confusing legal issue facing e-bike riders today is the difference between a bike lane and bike path. A bike lane is a marked section of roadway shared with motor vehicles. Bike paths pretty much universally prohibit the use of motorized vehicles. Still, you will need to research your area. As an example: “A path near our office specifically says “no motorized bicycles.” Yet, when we tracked down an employee who claimed to work enforcement on the path, he said that our e-bike was allowed.”8
J. K. Starley's company became the Rover Cycle Company Ltd. in the late 1890s, and then simply the Rover Company when it started making cars. Morris Motors Limited (in Oxford) and Škoda also began in the bicycle business, as did the Wright brothers.[101] Alistair Craig, whose company eventually emerged to become the engine manufacturers Ailsa Craig, also started from manufacturing bicycles, in Glasgow in March 1885.

My homeowners (State Farm) covers bikes , but assumes $500 per bike. They will add the bikes as personal property, but the premium is excessive (about $300/year per bike, and we have four bikes). I did increase our personal umbrella liability coverage, and it covers us if family members any sort of accident on our e-bikes that injures us or others or others' property, though only covers $500 each for our own bikes (under the homeowners coverage). It was not very expensive to increase the umbrella policy (as it resulted also in a reduced rate on our car insurance).

This electric bike received a five star. The assembly was pretty simple. I ordered a set of lights and a over rear tire carrier rack from amazon that took longer to install than it took too assemble the bike.This is a solid built by that is attractive and worthy of this price point. The build quality of this bike was very good. So far I've done a few test and it runs perfect. I've put on 50+ miles on this bike and have used it on flat ground, dirt roads, rocky trails and grassy fields. The bike runs quicker than what I expected from a small 250 W hub motor. I really like it in almost every way.
The European Committee for Standardization (CEN) also has a specific Technical Committee, TC333, that defines European standards for cycles. Their mandate states that EN cycle standards shall harmonize with ISO standards. Some CEN cycle standards were developed before ISO published their standards, leading to strong European influences in this area. European cycle standards tend to describe minimum safety requirements, while ISO standards have historically harmonized parts geometry.[55]
Electric bikes are becoming a convenient and fun way to commute around a city, but they can be pricey. The average e-bike can cost $3,000, with some models getting up to $5,000 or more. But these prices are dropping, as new models come onto the market — and if you don’t mind giving up some of the glossier, high-tech features like embedded digital displays, retractable cable locks, and and theft tracking and recovery, you can find a really good quality e-bike for under $1,500.
The battery is the pedelec’s power source. It supplies the motor with the electrical energy that is required to provide power assistance when cycling. So it is hardly surprising that there is frequent discussion and “talking shop” about the eBike’s battery in particular. What is the difference between batteries? How far can you go on a fully charged battery? What do you have to remember about storage? Thomas Raica, head of technical customer application, here provides information and advice.
Operators are subject to driving rules and equipment requirements (if applicable) when operated on the public streets or highways (which includes the main traveled portion of the road, shoulder and sidewalk). This means that an operator could be cited for speeding, failure to signal, unsafe change of course, driving on the sidewalk, DWI (this would apply to anywhere in the state and not just the streets/highways), and all other driving rules contained within state law that would apply. They may also not ride more than two abreast and may not impede the normal and reasonable movement of traffic. On a laned roadway, they must operate within a single lane.[citation needed]
While we're still fairly new to the solar ebike game, Mark is among the (suprisingly numerous) Grin customers who've been thinking about and experimenting with solar bikes for many years. After he shared pictures of his latest project and mentioned his round the world touring ambitions, we thought we had to do a small feature on this guy. A quick last minute trip to Maker Faire was arranged to meet up, and here we present, Mark Havran:
Depending on local laws, many e-bikes (e.g., pedelecs) are legally classified as bicycles rather than mopeds or motorcycles. This exempts them from the more stringent laws regarding the certification and operation of more powerful two-wheelers which are often classed as electric motorcycles. E-bikes can also be defined separately and treated under distinct Electric bicycle laws.
This little bike is great I weight like 175 and it's just great it can go up hills and it's an awesome little bike for NYC cops give me no issues and with a phone mount you can see your speed and battery life you have left... It's just a great bike nice and light I can pick up with one hand and it folds. The only cons I would say is I wish the battery lasts longer I get around 6.5 miles at full throttle at varying terrain and the horn is weak, I installed an air horn on my bike

Powered by a 250-watt Brose Centerdrive system, the Redux is capable of reaching speeds of up to 28 mph, which comes in handy when dodging traffic. The lithium-ion battery provides enough juice to give the bike a range of up to 80 miles between recharges, making it a great option for daily commuters. Raleigh even outfitted the bike with wide tires which provide stability and traction, even when the road gets wet. Other key features include a 10-speed Shimano crankset and shifters and a built-in LCD screen that displays all the usual information.


There are specialized bicycle tools for use both in the shop and on the road. Many cyclists carry tool kits. These may include a tire patch kit (which, in turn, may contain any combination of a hand pump or CO2 Pump, tire levers, spare tubes, self-adhesive patches, or tube-patching material, an adhesive, a piece of sandpaper or a metal grater (for roughing the tube surface to be patched), Special, thin wrenches are often required for maintaining various screw fastened parts, specifically, the frequently lubricated ball-bearing "cones".[57][58] and sometimes even a block of French chalk.), wrenches, hex keys, screwdrivers, and a chain tool. There are also cycling specific multi-tools that combine many of these implements into a single compact device. More specialized bicycle components may require more complex tools, including proprietary tools specific for a given manufacturer.
Maruti Suzuki Q4 profit down 5% at Rs 1,795 crore / Maruti Suzuki announces price hike for Baleno variants / Harley-Davidson Q1 earnings fall 26.8% in 2019 / Groupe PSA to source Rs 15,000 crore of India auto components in 3-5 years / Triumph will sell pre-owned motorcycles to lower entry price-point into the brand / Audi launches Lifestyle Edition of Q7 and A4 / Triumph Motorcycles launches Speed Twin in India at Rs 9.46 lakh / Maxxis tyres appoints first distributor for Uttarakhand / Mercedes Benz revamps two outlets in Nagpur / Ather Energy to enter Chennai in June
The Alpha has a  36V Brose 50W motor which is fueled by a “bridging” lithium-ion battery with 150 Wh of capacity, which is charged by the onboard 150 W PEM Hydrogen fuel cell. The fuel cell is fueled by a 2 litre compressed hydrogen gas cylinder, which can be refilled in about 2 minutes at a filling station.  In terms of cost per charge, this is likely to be more than a standard electric bike, however, the convenience of faster recharging may make it suitable for some riders, particularly commercial fleet operators using ebikes on shifts for several riders.
J. K. Starley's company became the Rover Cycle Company Ltd. in the late 1890s, and then simply the Rover Company when it started making cars. Morris Motors Limited (in Oxford) and Škoda also began in the bicycle business, as did the Wright brothers.[101] Alistair Craig, whose company eventually emerged to become the engine manufacturers Ailsa Craig, also started from manufacturing bicycles, in Glasgow in March 1885.
×