Being member of European Economic Area (EEA), Norway implemented the European Union directive 2002/24/EC. This directive defined legal ebikes for all EU and EEA countries to cycle "with pedal assistance which are equipped with an auxiliary electric motor having a maximum continuous rated power of 0.25 kW, of which the output is progressively reduced and finally cut off as the vehicle reaches a speed of 25 km/h or if the cyclist stops pedaling." The definition became part of Norwegian vehicle legislation in 2003. A more detailed specification will become effective when the new European ebike product safety standard EN 15194 is published in 2009.
Power assisted bicycles are classified in two categories in Saskatchewan. An electric assist bicycle is a 2 or 3 wheeled bicycle (sic.: 3 wheeled bicycle) that uses pedals and a motor at the same time only. A power cycle uses either pedals and motor or motor only. Both must have engines with 500 watt power or less, and must not be able exceed 32 km/h (20 mph), i.e., electric motor cuts out at this speed or cycle is unable to go this fast on a level surface. The power cycle has to meet the Federal Motor Vehicle Safety Standards for a power-assisted bicycle. The power cycle requires at least a learner's driving licence (class 7), and all of the other classes 1-5 may operate these also. The electric assist bicycle does not require a licence. Helmets are required for both. Both are treated as bicycles regarding rules of the road. Gas powered or assisted bicycles are classified as motorcycles regardless of engine size or if using pedals plus motor. Stickers identifying the bicycle's compliance with the Federal classification may be required for power cycles by some cities or municipalities. 
In New Zealand, the regulations read: "AB (Power-assisted pedal cycle) A pedal cycle to which is attached one or more auxiliary propulsion motors having a combined maximum power output not exceeding 300 watts." This is explained by NZTA as "A power-assisted cycle is a cycle that has a motor of up to 300 watts. The law treats these as ordinary cycles rather than motorcycles. This means that it is not necessary to register or license them. Note that the phrase "maximum power output" that is found in the regulation (but omitted in the explanation) may create confusion because some e-bike motor manufacturers advertise and print on the motor their "maximum input power" because that number is larger (typically motors run at about 80% efficiency ) thus give the impression the buyer is getting a more powerful motor. This can cause misunderstandings with law enforcement officers who do not necessarily understand the difference, and when stopping a rider on an e-bike in a traffic stop, look at the number on the motor to determine if the e-bike is legal or not.
The Wavecrest Tidalforce M-750 was based on The original military experimental M-313 model. The M-313/M-750X was the first electric bike to be made and tested by Wavecrest Labs. It is based on a design developed for the Defense Advanced Research Projects Agency (DARPA) that was meant to allow zero-heat long distance troop movements for the United States Marine Corps in Afghanistan. The rear wheel in-hub motor and 36 volt/8ah front-hub battery were mounted onto a standard Montague Bicycles Paratrooper Bicycle frame. The 1000 watt rear hub motor had no set speed restriction, but was limited to about 25-32 (depending on load weight) MPH on a flat course. The distance the bike traveled on a single charge ranged from 15 miles (heavier load with no pedaling) to about 25 miles (vigorous assisted pedaling with less hill climbing).
But unlike other battery mounted controllers, the Baserunner also stands on its own too. If you upgrade to a different battery model in the future that doesn't fit the cradle, simply remove the Baserunner from the base and use it as a miniature stand alone controller with your new battery pack. That's Grin thinking about your future options for you.
An e-bike is identified as a "motor assisted cycle" (MAC) in British Columbia, which differs from electric mopeds and scooters, which are "limited-speed motorcycles." Motor assisted cycles must: have an electric motor of no more than 500 W; have fully operable pedals; not be capable of propelling the device at a speed greater than 32 km/hr [19.9 mph]. The engine must disengage when (a) the operator stops pedaling, (b) an accelerator controller is released, OR (c) a brake is applied. A driver's license, vehicle registration, and insurance are all not required. A bike helmet must be worn.