I have been able to find ebikes of all speeds out in the wild and after years of riding and a reflective posture for the law, I see that lawmakers were thinking less about me and my practical wants as the user, and more about the mass motor vehicle driving public, their perceptions and expectations of ‘typical bicycle speeds’ on the roads and paths. So the laws were made to bicycle NORMS, not the potential performance limits for users.
The Consumer Product Safety Commission(CPSC) stipulates that commercially manufactured low-speed electric bicycles, or tricycles, must have fully operable pedals, an electric motor not exceeding 750W of power and a top motor-powered speed not in excess of 20 miles per hour (32 km/h).[22] An electric bike remaining within these specifications will be regarded simply as a bicycle for purposes of safety standards. This supersedes any state law that is more stringent, but only regarding safety equipment required on electric bicycles and the standard of manufacture they must meet.[23]. The legislation enacting this amendment to the CPSC is also known as HR 727[24].

Oklahoma defines an Electric-Assisted Bicycle in 47 O.S. 1-104 [122] as "Two or three wheels; and Fully operative pedals for human propulsion and equipped with an electric motor with a power output not to exceed one thousand (1,000) watts, incapable of propelling the device at a speed of more than thirty (30) miles per hour on level ground, and incapable of further increasing the speed of the device when human power alone is used to propel the device at a speed of thirty (30) miles per hour or more. An electric-assisted bicycle shall meet the requirements of the Federal Motor Vehicle Safety Standards as set forth in federal regulations and shall operate in such a manner that the electric motor disengages or ceases to function when the brakes are applied."


Electric bikes aren’t just a practical and environmentally conscious solution to gridlock, they also are really fun to ride. On top of all of the persuasive arguments to get an electric bike, I think the Rad Wagon’s best-selling point comes down to enjoyment. Zooming down the street each morning I wasn’t angrily yelling at fellow drivers or rushing not to be late. The bike commute was part of the journey each day, and not just the means I used to get around. There’s a reason so many people loved biking as a kid, and it can be just as fun as an adult.
Hub motors are sold as either geared or direct drive: Geared hubs are preferred for hill climbing ability and zero drag when coasting, while DD hubs are more durable and suitable for high speed. Extreme hill climbing and high torque applications (fatbikes, hauling cargo, popping wheelies) usually requires a mid drive, which is covered in the motor section below. Ebike battery packs from the listed suppliers are generally compatible with kits from any supplier, at worst you may need a different connector, which can be easily replaced. You probably want a battery pack that is 36, 48, or 52 volts, depending on whether you prefer lower price and longer range or a higher topspeed. DIY lipo battery packs can be built cheaply but doing so can be a fire hazard so actual packs are recommended. All hub motors above 24 V should be installed with torque arms for safety.

(15.5) "Electric assisted bicycle" means a device with two or three wheels which has a saddle and fully operative pedals for human propulsion and also has an electric motor. For such a device to be considered an electric assisted bicycle, it shall meet the requirements of the Federal Motor Vehicle Safety Standards, as set forth in 49 C.F.R. Section 571, et seq., and shall operate in such a manner that the electric motor disengages or ceases to function when the brakes are applied. The electric motor in an electric assisted bicycle shall:

State laws tend to intermix the source of power as either gasoline ICE or electric drive. This is unfortunate because that neutralizes the environmental advantage of an ebike over an ICE moped. It also misrepresents the contrast in power output levels between an ICE and electric motor system. 50cc gas mopeds/scooters have a 2.5-4 HP rating, while the 20+ mph electric bikes will be 1-2hp, and ride much closer to a normal bicycle compared to a gas powered, 2.5hp moped. E-mopeds will weigh 55-70lbs. Gas mopeds and scooters are typically over 120lbs. E-mopeds are still electric bikes that get valuable power assist from human pedal effort and are usually much quieter.


What's the Centros like? Big and heavy, but with enough power to overcome that, it really reminded me of a more upmarket Volt Pulse. You do tend to find that the weightier e-bikes give more of a feeling of speed, even though you're only doing 20mph or so at the absolute most (only up to 15mph with electrical assistance so you'll need leg muscles or a downward incline to get to that outlandish velocity).
For people wanting to push the effects of Statorade to the max, the Australian made Hubsinks can clamp on to your motor shell and provide additional cooling fins to shed heat to ambient air. These fit our new MXUS Cassette motors, and the 9C, Crystalyte H, and many others. These are listed on our new store category for motor cooling mods. And like other small products, we try to  keep a stock of 10mL Statorade syringes on Amazon for easy shipping to US customers. They are sold out now but another shipment is inbound. 
Motor: We have a blog post showing some motor differences: https://www.ebikekit.com/blogs/news/its-whats-inside-your-motor-that-counts Cabling is probably the #1 issue when something goes wrong. Good connectors, good cables, and good assembly (bike shop!) are crucial Strain reliefs on all cable joints! Where you have a junction box or a connector, the stress is concentrated over a small area near this stiff spot on the cable. This can cause small breaks on the internal wires, causing a disconnect or a short. This is a major reason for failure. Strain reliefs are more expensive – you need special tooling, skilled labor, and appropriate materials to...

While the first functional battery was developed in the year 1800 by Italian physicist Alessandro Volta, a practical battery would not be seen for several decades yet. By the end of the 19th century, practical and portable batteries were more widely available, this finally freeing the electric motor to be used in a wide new array of applications. It might come as a surprise, but the electric motor, battery, and a bicycle were first paired as far back as the 1890s. It would be approximately 100 years later that electric bicycle development finally entered the mainstream, but the technology and concept behind the electric bike were all in place generations ago.
An affordable GPS enabled bike security alarm device with text and email updates, runs on the 2G Verizon network to send notifications about location and status, includes iPhone, Android and web apps to control the device, track, and download ride data. Mounts to any standard bottle cage bosses if there is enough horizontal room, the device is 10" long and 3/4" thick with rubberized contacts to reduce vibration, rear rack and quick clamp mounting accessories available to work with just about any bike...
State laws tend to intermix the source of power as either gasoline ICE or electric drive. This is unfortunate because that neutralizes the environmental advantage of an ebike over an ICE moped. It also misrepresents the contrast in power output levels between an ICE and electric motor system. 50cc gas mopeds/scooters have a 2.5-4 HP rating, while the 20+ mph electric bikes will be 1-2hp, and ride much closer to a normal bicycle compared to a gas powered, 2.5hp moped. E-mopeds will weigh 55-70lbs. Gas mopeds and scooters are typically over 120lbs. E-mopeds are still electric bikes that get valuable power assist from human pedal effort and are usually much quieter.
While we won't be there in person, a number of vehicles will be at the show featuring the new Grin products like the GMAC Hub Motors, RH212 direct drive motors, All Axle hubs, and the Baserunner and Phaserunner_L10 controllers.  If you're lucky enough to attend then check out Booth A.18 and Booth 3.12 for some velomobiles and cargo vehicles running this gear.  
In my experience, there aren’t people out checking on ebike classes and the way you ride has a lot more to do with being stopped than what you are riding. I have never been stopped on an ebike anywhere for any reason. The bigger risk is riding a faster and even more powerful electric bike that would be categorized as a moped without a license and that if you got into an accident, you could be liable for more and charged with driving an unregistered vehicle or something. It’s great that you’re being careful and thinking about how to fit into the community, that alone goes a long way
Oklahoma defines an Electric-Assisted Bicycle in 47 O.S. 1-104 [122] as "Two or three wheels; and Fully operative pedals for human propulsion and equipped with an electric motor with a power output not to exceed one thousand (1,000) watts, incapable of propelling the device at a speed of more than thirty (30) miles per hour on level ground, and incapable of further increasing the speed of the device when human power alone is used to propel the device at a speed of thirty (30) miles per hour or more. An electric-assisted bicycle shall meet the requirements of the Federal Motor Vehicle Safety Standards as set forth in federal regulations and shall operate in such a manner that the electric motor disengages or ceases to function when the brakes are applied."
Biking is awesome, but biking uphill is not. Commuting by bike is environmentally friendly, fun and good for your health, but presenting your sweaty self to your office coworkers in not fun at all. Fortunately, there is a solution! Electric bicycles offer the same great benefits as traditional bicycles including cost savings, health improving, plus some additional advantages like efficiency in climbing hills, less stress on knees and joints, which is convenient for people of all ages and health.
We use cookies to optimise the content and display of our pages, to offer social media functionality and to analyse access to our website without creating a profile. In addition, when using the social media share functionality, information on the use of our website is transmitted to the respective providers. Use of the cookies necessary for this purpose can be deactivated in the Privacy Policy. Learn more.
I have been able to find ebikes of all speeds out in the wild and after years of riding and a reflective posture for the law, I see that lawmakers were thinking less about me and my practical wants as the user, and more about the mass motor vehicle driving public, their perceptions and expectations of ‘typical bicycle speeds’ on the roads and paths. So the laws were made to bicycle NORMS, not the potential performance limits for users.
This upgraded model is the best scooter of this type that is currently available on the market. I have permanent mobility issues because of my left leg that do not allow me to walk any long distances. This scooter is allowing me to finally get out of the house to see and do some things again, even if that is just cruising around the neighborhood, but my main reason for purchasing it was so that I can go watch my granddaughters playing softball this spring, they are quite good.
Both the Stromer and the Stoeckli are very nice looking designs and easy to handle. Reliability for both does not seem to be up to Swiss standards, e.g. some of the 2012 Stöcklis seem to have bad contacts. However, as of 2013, most of these problems should be fixed. The Cube got criticized for its battery/saddle system, but this has probably been fixed in more recent edition and it has less "punch" then the other's since the motor is smaller (324W?). I don't know about the BH Neo Nitro. Given the relatively low price of the BH Nitro, it may be the best buy in this category if you plan to cover smaller distances (the battery is limited to 9Ah, and Spain's industry does need some help ;) Anyhow, all of these models come with a variety of motors and country-specific modifications. E.g. in France, the BH Nitro comes with a 350W motor and is electronically limited to 25km/h, whereas in Switzerland you either can get a 500W - 45 km/h version or a 250W? - 25km/h version.
This dexterous electric dirt bike is recommended for anyone over the age of 14. It’s fitted with double suspension and big tyres to help you tackle tough terrain. You also get a good selection of gears, that gives you optimal control. The Razor can go as fast as 20 mph, and comes with an excellent braking system. The aesthetics are on point, and the racer look is sure to impress. Don’t forget your helmet!
A KS LEV Integra dropper post, 130mm of front and rear travel, 27.5-inch wheels, and trail-grabbing 2.8-inch tires make this pedal-assist mountain bike a great option if you want to climb farther to shred longer, but don’t want to lug your bike uphill for ages. The 250-watt motor, placed slightly farther forward than most other bikes to optimize weight distribution and handling, provides a nice boost so you can enjoy the ride up and not be too gassed when you get to the top.

Can I legally buy/build and ride an ebike that’s faster than 20 mph? Yes you can, but you need to know that the ebike is no longer considered equivalent to a bicycle and is subject to other state vehicular classifications. The definitions for electric bikes spanning 20-30mph, and 1-2 horsepower ranges, will vary from state to state, resulting in a no-man’s-land consensus about limits for motor vehicle definition. The common label for a 20-30mph, 2-wheeled vehicle with active pedals is a Moped. Other MVA labels include motor scooter, motorbike and dirt bike which may have equivalent power and speed performance, but do not have pedals to assist and move the vehicle.
Oklahoma defines an Electric-Assisted Bicycle in 47 O.S. 1-104 [122] as "Two or three wheels; and Fully operative pedals for human propulsion and equipped with an electric motor with a power output not to exceed one thousand (1,000) watts, incapable of propelling the device at a speed of more than thirty (30) miles per hour on level ground, and incapable of further increasing the speed of the device when human power alone is used to propel the device at a speed of thirty (30) miles per hour or more. An electric-assisted bicycle shall meet the requirements of the Federal Motor Vehicle Safety Standards as set forth in federal regulations and shall operate in such a manner that the electric motor disengages or ceases to function when the brakes are applied."

"Moped" means a device upon which a person may ride which has two or three wheels in contact with the ground, a motor having a maximum power output capability measured at the motor output shaft, in accordance with the Society of Automotive Engineers standards, of two horsepower (one thousand four hundred ninety -two watts) or less and, if it is a combustion engine, a maximum piston or rotor displacement of 3.05 cubic inches (fifty cubic centimeters) and which will propel the moped, unassisted, on a level surface at a maximum speed no greater than thirty miles per hour; and a direct or automatic power drive system which requires no clutch or gear shift operation by the moped driver after the drive system is engaged with the power unit.
Operators are subject to driving rules and equipment requirements (if applicable) when operated on the public streets or highways (which includes the main traveled portion of the road, shoulder and sidewalk). This means that an operator could be cited for speeding, failure to signal, unsafe change of course, driving on the sidewalk, DWI (this would apply to anywhere in the state and not just the streets/highways), and all other driving rules contained within state law that would apply. They may also not ride more than two abreast and may not impede the normal and reasonable movement of traffic. On a laned roadway, they must operate within a single lane.[citation needed]
The frame itself incorporates a series of mounts allowing you to easily trick-out the Road E+1 with a rack, fenders, or panniers to more aptly meet your touring requirements. Again, most touring purists will certainly scoff at the mere notion of pedal-assistance, however, individuals looking for more of a guided tour and less of a tour de force will swoon over the Road E+1.
On February 4, 2014, SB997 was introduced by Senator Matt Smith, which seeks to amend PA Vehicle Code to include "Pedalcycle with Electric Assist". In a memo addressed to all senate members, Smith said the definition shall include "bicycles equipped with an electric motor not exceeding 750 watts, weighing not more than 100 pounds, are capable of a maximum speed of not more than 20 mph, and have operable pedals."[128][129]
The benefits don’t stop at the physical, however. Our daily lives are spent glued to computer and phone screens, and even if you choose to accept that as an inevitable wave of the future, your mind still needs a release from all that toxic screen time. Because a bike moves more slowly than a car, while also giving you much better sight lines and more direct exposure to the sun, a nice ride — even through city streets — will put you more in touch with nature. Getting in touch with your natural environment can drastically reduce stress levels, which is why biking to and from work is such a good idea: no matter how frustrating your day at the office was, you can let it all go on the enjoyable cycling trip home.
From the beginning and still today, bicycles have been and are employed for many uses. In a utilitarian way, bicycles are used for transportation, bicycle commuting, and utility cycling. It can be used as a 'work horse', used by mail carriers, paramedics, police, messengers, and general delivery services. Military uses of bicycles include communications, reconnaissance, troop movement, supply of provisions, and patrol. See also: bicycle infantry.
The two most common types of hub motors used in electric bicycles are brushed and brushless. Many configurations are available, varying in cost and complexity; direct-drive and geared motor units are both used. An electric power-assist system may be added to almost any pedal cycle using chain drive, belt drive, hub motors or friction drive. BLDC hub motors are a common modern design. The motor is built into the wheel hub itself, and the stator fixed solidly to the axle, and the magnets attached to and rotating with the wheel. The bicycle wheel hub is the motor. The power levels of motors used are influenced by available legal categories and are often, but not always limited to under 750 watts.

5. Prizes: The approximate retail value of all prizes is $1361. The prizes are: Performance E-BikeKit or Heavy Duty E-BikeKit. You are not guaranteed to win a prize and your chance of winning is dependent on the total number of eligible entries received. Actual/appraised value may differ at time of prize award. The specifics of the prize shall be solely determined by the Sponsor. No cash or other prize substitution permitted except at Sponsor's discretion. The prize is nontransferable. Any and all prize related expenses, including without limitation any and all federal, state, and local taxes shall be the sole responsibility of the winner. No substitution of prize or transfer/assignment of prize to others or request for the cash equivalent by winners is permitted. Acceptance of prize constitutes permission for Electric Bike Technologies INC. to use winner's name, likeness, and entry for purposes of advertising and trade without further compensation, unless prohibited by law.


Electric Bicycles are defined by the California Vehicle Code [32][33]. In summary, electric bicycles are to be operated like conventional bicycles in California. There are several exceptions to this. A person must be at least 16 years old, and anyone riding an electric bicycle must wear a bicycle helmet. The e-bikes must have an electric motor that has a power output less than 1,000 watts, is incapable of propelling the device at a speed of more than 20 miles per hour on level ground, is incapable of further increasing the speed of the device when human power is used to propel the motorized bicycle faster than 20 miles per hour, operates in a manner so that the electric motor is disengaged or ceases to function when the brakes are applied, or operates in a manner such that the motor is engaged through a switch or mechanism that, when released, will cause the electric motor to disengage or cease to function.
Vehicles exceeding any of the criteria above must be registered and titled as a motorcycle. Other types of vehicles, such as electric scooters, "pocket rockets" and mini-choppers, may fit the definition of a moped or a motorcycle, but cannot be registered by the Department of State if they lack the equipment required by law to legally drive on public roads.[101]
A wandering writer who spends as much time on the road as in front of a laptop screen, Brett can either be found hacking away furiously at the keyboard or, perhaps, enjoying a whiskey and coke on some exotic beach, sometimes both simultaneously, usually with a four-legged companion by his side. He has been a professional chef, a dog trainer, and a travel correspondent for a well-known Southeast Asian guidebook. He also holds a business degree and has spent more time than he cares to admit in boring office jobs. He has an odd obsession for playing with the latest gadgets and working on motorcycles and old Jeeps. His expertise, honed over years of experience, is in the areas of computers, electronics, travel gear, pet products, and kitchen, office and automotive equipment.

Electric bicycles have two main methods of operation: pedal-assist and/or throttle-control. As the name implies, pedal-assist “assists” your pedaling and requires some input. With this method, a torque sensor picks up movement or stress to determine the power requirements of the rider. Everything is automated so there’s nothing to think about, just jump on and start riding. Some bikes have multiple settings, while others have just one setting with the addition of a throttle control. Depending on the setting, pedal-assistance can help a little – or a lot. At lower settings, pedal-assist is barely noticeable but helps extend your range. At higher settings, the power is quite obvious and feels like a strong wind at your back with the motor doing most of the work while you pedal along.
Electric-assisted bicycles are treated as human-powered bicycles, while bicycles capable of propulsion by electric power alone face additional registration and regulatory requirements as mopeds. Requirements include electric power generation by a motor that cannot be easily modified, along with a power assist mechanism that operates safely and smoothly. In December 2008, The assist ratio was updated as follow:
A new electric cyclist will likely experience two conflicts of thought: 1). Will the general public accept my use of this power assist technology, or Will they ridicule and reject me as being lazy? 2). Will I stand out to law enforcement by the look of my bike or riding a bit faster than other cyclist on hills and roads? Grappling with these two thoughts will tempt most folks to try and remain unnoticed and ride more responsibly. After I became an advocate of e-transportation on two wheels, enjoying the benefits of power assist commuting, I eventually was a bit put off by this federal law, especially the 20mph limitation. Is 20 mph really practical and justified? Is it not true that many active young people on typical road bicycles are able to actively ride in the 20-25mph range? I discovered that ebikes, with larger tires and disk brakes, can comfortably and safety cruise in that range of speed. The standard 2001 Federal law of 20mph, eventually became a practical limitation for an ebike commuter of over 20 miles a day, and caused me to get a bike beyond the federal limits, making me more alert and sensitive when riding in the presence of the police.
Cargo bikes and city bikes are common in the e-bike space, but until recently we haven’t seen that many performance road bikes. The Giant Road E+1 is a pedal-assist performance road bike that’s made for more than just commuting; the powerful motor can crank you up to 28 mph very quickly on the highest setting so you can rip the flats, join your local group ride, or blast through the mountains with far less effort than a traditional road bike. It won’t feel like a 16-pound race bike when you lean it into high-speed turns, but the endurance-oriented geometry allows for an aggressive position on the bike and keeps it nimble and agile at high speed.
A new electric cyclist will likely experience two conflicts of thought: 1). Will the general public accept my use of this power assist technology, or Will they ridicule and reject me as being lazy? 2). Will I stand out to law enforcement by the look of my bike or riding a bit faster than other cyclist on hills and roads? Grappling with these two thoughts will tempt most folks to try and remain unnoticed and ride more responsibly. After I became an advocate of e-transportation on two wheels, enjoying the benefits of power assist commuting, I eventually was a bit put off by this federal law, especially the 20mph limitation. Is 20 mph really practical and justified? Is it not true that many active young people on typical road bicycles are able to actively ride in the 20-25mph range? I discovered that ebikes, with larger tires and disk brakes, can comfortably and safety cruise in that range of speed. The standard 2001 Federal law of 20mph, eventually became a practical limitation for an ebike commuter of over 20 miles a day, and caused me to get a bike beyond the federal limits, making me more alert and sensitive when riding in the presence of the police.
The Wavecrest Tidalforce M-750 was based on The original military experimental M-313 model had a 1000 watt electric hub motor mounted into the rear wheel of a folding Montague Bicycles Paratrooper Bicycle frame and a 36 volt battery pack mounted into the front wheel hub. The later commercial versions had speed restrictions to comply with federal law with 750 watt restrictions (500 watts maximum in the Canadian version) but had 1000 watt unresricted speed as an add on option. The M-313/M-750X was the first electric bike to be made and tested by Wavecrest labs. It is based on a design developed for the Defense Advanced Research Projects Agency (DARPA) that was meant to allow zero-heat long distance troop movements for the United States Marine Corps in Afghanistan.
To operate the bike, you have to pedal for a second or so before the thumb throttle becomes active. This is often a cost and energy-saving measure designed into electric bicycles and scooters. Being able to start the motor from rest requires extra sensors and higher battery power. Starting the motor while it is in motion removes the need to install extra sensors in the motor (and thus removes one more possible failure or maintenance issue) and also eeks more range out of the battery by putting the energy intensive initial startup responsibility solely on the rider.
There is however still confusion over the various legislations involving Electric Bicycles. This stems from the fact that while places like the US and Canada offer some Federal regulation, the legality of road use is left to the various States or Provinces and then complicated further by municipal laws and restrictions. Further more there are a range of classifications and terms describing them, "Power-assisted bicycle" (Canada) or "Power assisted cycle" (United Kingdom) or ”Electric pedal assisted cycles” (European Union) or simply "electric bicycles", and as such in some cases have varying laws according to their respective classifications in some places.
Since 30 May 2012, Australia has an additional new e-bike category using the European Union model of a pedelec as per the CE EN15194 standard. This means the e-bike can have a motor of 250W of continuous rated power which can only be activated by pedalling (if above 6 km/h) and must cut out over 25 km/h – if so it is classed as a normal bicycle. The state of Victoria is the first to amend their local road rules, see below.
In the early 1860s, Frenchmen Pierre Michaux and Pierre Lallement took bicycle design in a new direction by adding a mechanical crank drive with pedals on an enlarged front wheel (the velocipede). This was the first in mass production. Another French inventor named Douglas Grasso had a failed prototype of Pierre Lallement's bicycle several years earlier. Several inventions followed using rear-wheel drive, the best known being the rod-driven velocipede by Scotsman Thomas McCall in 1869. In that same year, bicycle wheels with wire spokes were patented by Eugène Meyer of Paris.[22] The French vélocipède, made of iron and wood, developed into the "penny-farthing" (historically known as an "ordinary bicycle", a retronym, since there was then no other kind).[23] It featured a tubular steel frame on which were mounted wire-spoked wheels with solid rubber tires. These bicycles were difficult to ride due to their high seat and poor weight distribution. In 1868 Rowley Turner, a sales agent of the Coventry Sewing Machine Company (which soon became the Coventry Machinists Company), brought a Michaux cycle to Coventry, England. His uncle, Josiah Turner, and business partner James Starley, used this as a basis for the 'Coventry Model' in what became Britain's first cycle factory.[24]
The other shout-out goes to Paul Bogaert who decided to close the Bike Doctor after 27 years and instead cycle tour the world with his wife. Paul had an early role in Vancouver bicycle advocacy and at bringing cycle riding to a less elitist/athletic and more everyday commuter crowd through their shop.  They were among the early shops to embrace family friendly cargo bikes and  appreciated the role that electric would play in making cycling more broadly appealing.

On the topic of visibility, there are a lot of things you can do to make yourself easier to see. You can throw on a reflective vest, for example, which has the added benefit of protecting your work clothes from flying dirt and debris. You can also add lights and reflectors to the bike itself, or strap illuminated bands to your arms and ankles. Both Gestalt theory and several biking visibility studies suggest that moving light sources like the reflectors on pedals that go up and down, are more visible to drivers because our visual systems are designed to pick up on movement (that of prey and predators evolutionarily), making reflective biking shoes a great idea.
Unrelated to the show but also of local interest. The BC government is soliciting input on what is meant by "active transportation" which could hopefully help to direct policy and regulation governing not just ebikes but all kinds of human scaled transport. If you think electric skateboards should be on their radar or faster S-Pedalec class ebikes then this is a chance to have your voice heard. Electric bicycles have been an entirely grass roots phenomenon for most of their trajectory and it's encouraging to see the entire scope of personal mobility finally being acknowledged and discussed at this level.
Hi Levi, I’m not super familiar with Minnesota or the age limits on ebikes but Pedego just launched one specifically for younger riders (it goes a little slower). Many ebikes let you program a top speed and I feel like this is one area where you can decide as a parent. When I was 13 I had a moped and fixed up a goped with my Grandpa on his farm so… I guess it might be a family decision?
But electric bicycles—e-bikes—are new territory for me. Broadly speaking, there are two basic options in e-bike land: power-on-demand and pedal-assist. With the former, the rider can control the speed with a throttle instead of just pedaling. Think moped but with an electric motor instead of internal combustion. Pedal-assist, by contrast, requires the rider to do some of the work. The electric motor won't engage unless the rider is pedaling. 
×